Optimized partitioning of a wavelength distributed data interfacering network

A fiber optic ring network, such as fiber distributed data interface (FDDI), can be operated over multiple wavelengths on its existing fiber plant consisting of point-to-point fiber links. Using wavelength division multiplexing (WDM) technology, FDDI nodes can be partitioned to operate over multiple subnetworks, with each subnetwork operating independently on a different wavelength, and inter-subnetwork traffic forwarding performed by a bridge. For this multiwavelength version of FDDI, which we refer to as wavelength distributed data interface (WDDI), we examine the necessary upgrades to the architecture of a FDDI node, including its possibility to serve as a bridge. The main motivation behind this study is that, as network traffic scales beyond (the single-wavelength) FDDI's information-carrying capacity, its multiwavelength version, WDDI, can gracefully accommodate such traffic growth. A number of design choices exist in constructing a good WDDI network. Specifically, we investigate algorithms using which, based on prevailing traffic conditions, partitioning of nodes into subnetworks can be performed in an optimized fashion. Our algorithms partition the nodes into subrings, such that the total traffic flow in the network and/or the network-wide average packet delay is minimized     

Calculation of shift of avalanche transit time phase delay due tooptically injected carriers in indium phosphide avalanche diodes

A computer method for the calculation of the phase shift due to optically injected carriers in an InP avalanche transit time diode has been suggested using the numerically simulated negative resistance profiles in the depletion layer of the diode. The results show that the phase shift due to hole injection is larger than that due to electron injection which explains the pronounced effect of photogenerated hole leakage current in modulating the microwave properties of InP diodes     

Radiation-Induced graft copolymerization of methacrylic acid onto polypropylene fibers. V. Mechanical properties

Mechanical properties of polypropylene-g-poly(methacrylic acid) fibers, prepared by graft copolymerization of methacrylic acid onto polypropylene fiber using simultaneous gamma ray irradiation technique, were evaluated. In general, an improvement in the mechanical behavior of the polypropylene fiber by grafting was observed. Denier and initial modulus of the fiber showed a linear increase with the percent graft, and elongation showed an opposite trend. The results have been explained in terms of reinforcing effect of poly(methacrylic acid) grafts and reduction in the segmental mobility of the polymeric chains. Tenacity also increases up to certain graft level, beyond which a sharp decrease occurs, probably due to the influence on the compactness of the macromolecular chains with the further grafting.     

Embedded deterministic test for low-cost manufacturing

You have probably heard that BIST takes too long and its fault coverage is low, and that deterministic test requires too many patterns. This article shows how on-chip compression and decompression techniques provide high fault coverage with low test times.     

Simplified steady-state model of an SCR-inverter-basedload-commutated commutatorless series motor

This paper presents a simplified analytical model of a silicon-controlled-rectifier based, load-commutated inverter driven, commutatorless series motor to predict its speed-current, torque-current and torque-speed characteristics. The model has been formulated, keeping in view the steady state equivalent circuit of a conventional DC series motor. The proposed analytical expressions relating torque and current with speed are found to follow an inverse law and that relating torque and current is found to be parabolic, as is expected in a "series" machine. The drive has been implemented, loaded with a DC generator and experimentally similar characteristics have been obtained, as predicted by the analytical model. The characteristics obtained experimentally are seen to follow the ones, predicted by the analytical model closely     

Effect of sillimanite beach sand composition on mullitization and properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> system

Mullite was developed by reaction sintering of sillimanite beach sand and calcined alumina. Two varieties of sillimanite beach sand viz. S and Z having different compositions were selected. Synthesis and properties of mullite were very much dependent on the sillimanite beach sand composition. Presence of higher amount of impurities in the Z-variety of sillimanite sand favours the densification by liquid phase formation. Presence of zircon in Z-variety increases the hardness and fracture toughness. Alumina addition improves the mechanical/thermomechanical properties of the samples. Mullite retains the usual orthorhombic habit of sillimanite. Rounded to sub rounded zirconia dispersed within the mullite matrix of the sample ZA is noticed.