Simulation of leachate migration in leaky aquifers

A two-dimensional cross-section finite difference model is presented to simulate density dependent leachate migration in leaky aquifers. Unlike existing models, a new approach is adopted to couple the groundwater-flow equation and the hydrodynamic dispersion equation with the elimination of the intermediate step of calculating velocities. The concept of the reference density is employed, permitting increased accuracy (over pressure-based models) in the representation of the transport process. The model is then used to study the effect of several hydraulic and transport parameters on the flow pattern and plume migration which are found to be very sensitive to most of these parameters. Equiconcentration and equipotential lines are overlapped to provide a better understanding of the coupling effect.     

Survival of rotavirus SA-11 on vegetables

Survival of rotavirus on lettuce, radishes, and carrots was studied to evaluate the potential of rotavirus transmission by vegetables irrigated with wastewater. The vegetables were contaminated with rotavirus SA-11 and stored at 4°C and room temperature in covered and uncovered containers to simulate post harvest conditions. Virus decay rates were greater on radishes and carrots than lettuce. Decay rates of rotavirus on lettuce, radish, and carrot ranged from ?0·057 to ?0·479 (log₁₀ pfu/day). Rotavirus SA-11 survived on lettuce, radish, and carrot for 25 to 30 days at 4°C but at room temperature survival was very different for the various vegetables varying from 5 to 25 days. Greatest survival was always observed on the lettuce. These data suggest that rotaviruses can survive long enough on contaminated vegetables as to be transmitted by this vehicle.     

Thermal and thermoelastic properties of fast extrusion furnace (FEF) carbon black loaded SBR vulcanizates

The effect of FEF carbon black as filler on the thermal capacity c, diffusivity a, and thermal conductivity λ, of styrene butadiene rubber (SBR) composites in the temperature range 300–420 K was studied. The filler strongly increases the thermal diffusivity, whilst strongly decreasing the thermal capacity and the thermal conductivity (except at high FEF content ≥80 phr). The influence of the filler on the thermoelastic behaviour of the same composites was also investigated. It was found that the thermoelastic temperature change (ΔT) increased with carbon black concentration as well as the entropy change per unit extension.     

Radiation polymerization of acrylonitrile in a viscous system with styrene

Radiation polymerization of acrylonitrile in a viscous system with styrene was performed at ambient temperature by using γ‐rays. It is found that the overall rate of polymerization was accelerated after critical conversion due to the gel effect. As the molar fraction of styrene in monomer feed (f_St) is increased, both the total polymer conversion and molar fraction of acrylonitrile in the copolymer feed (F_AN) were decreased. The monomer reactivity ratios for acrylonitrile and styerne were determined to be r₁ (AN) = 0.25 and r₂ (St) = 2.0, respectively. The copolymers obtained were characterized by Fourier transformed infrared spectra (FTIR), X‐ray diffraction (XRD), scanning electron microscopy (SEM), ¹H‐NMR, and pyrolysis mass spectrometry (PMS). It was found that the slight addition of styrene to acrylonitrile strongly changes crystallinity, morphology, and thermal decomposition of the resulting polymer. ¹H‐NMR measurment of AN/St copolymer showed the appearance of aromatic proton signals and shifted the resonance of the methylene proton to lower chemical shifts. The mass spectra of AN/St copolymers showed fragments of pyrolysates corresponding to oligonitriles with styrene end groups. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 268–275, 2002; DOI 10.1002/app.10324     

Performance analysis of a solar-assisted swimming pool heating system

This paper deals with feasibility studies for a solar-assisted heating system for the University of Miami's Aquatic Center using the simulation program TRNSYS. The Aquatic Center is composed of an outdoor olympic size swimming pool and locker room building. The solar heating is accomplished by employing hot water generated by heat exchange with the solar collector working fluid. Two thermal storage tanks are employed for the collector and domestic use. The performance of the system is analyzed from both thermodynamic and economic standpoints and general conclusions are reached.     

SiGe: An attractive material for post-CMOS processing of MEMS

This work gives an overview of the different developments for silicon germanium (Si_1−xGe_x) from a MEMS post-processing perspective. First, the maximum processing temperature that does not introduce any damage or degradation into the standard characteristics of the CMOS driving electronics is specified. Then, the optimal type of silicon and germanium gas sources and deposition technique that results in an economical process are identified. Next, the selection criteria for a low thermal budget doping method and doping species are discussed. Finally, the advantage and disadvantage for the different approaches implemented for enhancing the physical properties of poly Si_1−xGe_x at a CMOS backend compatible temperature are highlighted. It is shown that the optimal method depends on the application requirements and the CMOS technology used for realizing the driving electronics.     

The Impact of Metastable Intermolrecular Nanocomposite Particles on Kinetic Decomposition of Heterocyclic Nitramines Using Advanced Solid‐Phase Decomposition Models

Journal of Inorganic and Organometallic Polymers and Materials - Surface oxygen of oxide catalyst has low coordination number; they are negatively charged. Surface oxygen can act active site for...     

Effect of Zn and Pb as alloying elements on the electrochemical behavior of brass in NaCl solutions

The electrochemical behavior of brasses with various Zn content (5.5–38 mass%) and brass (Cu–38Zn) with different Pb contents (1–3.4 mass%) in 0.6 M NaCl was investigated. The effects of temperature, immersion time, and concentration of chloride ions on the behavior of the different alloys were studied. The pitting corrosion behavior of Cu–Zn alloys and leaded–brass alloys in 0.6 M NaCl solution was also investigated. Open-circuit potential measurements (OCP), polarization techniques and electrochemical impedance spectroscopy (EIS) were used. The results show that the increase in the Zn content increases the corrosion rate of the brass alloys in chloride solutions, while the increase of Pb content in Cu–38Zn–Pb decreases the corrosion rate of the alloy. Long immersion time of the alloys in the aqueous electrolyte improves their stability due to the formation of passive film on the alloy surface. The breakdown potential is shifted to more negative direction with increasing the Zn content, whereas it shifts towards positive values with increasing Pb content. Equivalent circuit model for the electrode/electrolyte interface under different conditions was proposed to illustrate the electrochemical processes taking place at the interface. The electrochemical behavior of the different alloys was discussed in view of the fitting results.     

Recycling of pharmaceutical waste gelatin for controlled‐release applications. I. A 2,4‐dicholorphenoxy acetic acid based system

Gelatin is a natural macromolecular protein. It contains a wide variety of amino acids in its polymer structure, and it is colorless to yellowish, water‐soluble, and tasteless. It is used as a dispersing agent, sizing medium, and coating for photographic films and in pharmaceutical formulations. In this study, biodegradable mulching, based on waste gelatin from pharmaceutical gelatin scraps (derived from pharmaceutical soft gelatin capsule production), was formulated via the casting of water solutions or suspensions into flexible and consistent films. Gelatin was blended with synthetic materials such as poly(vinyl alcohol) and other natural wastes such as sugar cane bagasse and sawdust. To all formulations, 2,4‐dichlorophenoxy acetic acid (2,4‐D) was added as a herbicide. The morphology and mechanical properties of the samples were investigated with scanning electron microscopy and tensile testing, respectively. The results showed that the produced films had controlled‐release properties. The effects of various additives and crosslinking on the films and the release of the herbicide 2,4‐D from the films were also investigated. The introduction of synthetic and natural additives reduced the release rate of 2,4‐D. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2313–2319, 2004     

Difference between mechanical alloying and mechanical disordering in the amorphization reaction of Al50Ta50 in a rod mill

Amorphous Al₅₀Ta₆₀ alloy powders have been synthesized by mechanical alloying (MA) from elemental powders of aluminium and tantalum, and mechanical disordering (MD) from crystalline intermetallic compound powders of AlTa respectively using the rod milling technique. The mechanically alloyed and the mechanically disordered alloy powders were characterized by X-ray diffraction, scanning electron microscopy, electron probe microanalysis, transmission electron microscopy, differential thermal analysis, differential scanning calorimetry and chemical analysis. The results have shown that the crystal-to amorphous transformation in the MD process occurs through one stage, while the crystallineto-amorphous formation in the MA process occurs through three stages. At the early and intermediate stages of the MA time, heating the alloy powders to 700 K leads to the formation of an amorphous phase by a solid-state amorphizing reaction. At the final stage of the MA time, the amorphous phase is crystallized through a single sharp exothermic peak. Contrary to this, amorphous alloy powders produced by MD are crystallized through two broad exothermic peaks.