A cathode readout gas sampling calorimeter with conductive plastic tubes

We constructed and tested a prototype gas sampling electromagnetic calorimeter of the Pb-proportional tube sandwich type. The calorimeter uses conductive plastic tubes and cathode pad readout with a tower structure which resulted in reasonable energy and spatial resolutions for electrons in the momentum range 0.5–4.0 GeV/c; $\text{σ}{}_{\mathrm{E}}\text{E =}\text{21\%}\text{(E(}\text{GeV}\text{)}\text{)}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{, σ}{}_{\mathrm{x}}\text{= 6}\text{mm}\text{(at 3 GeV}$/c). This paper describes the test and the performance studied under various conditions.     

[110]-surface strained-SOI CMOS devices

We have newly developed [110]-surface strained-silicon-on-insulator (SOI) n- and p-MOSFETs on [110]-surface relaxed-SiGe-on-insulator substrates with the Ge content of 25%, fabricated by applying the Ge condensation technique to SiGe layers grown on [110]-surface SOI wafers. We have demonstrated that the electron and the hole mobility enhancement of [110]-surface strained-SOI devices amounts to 23% and 50%, respectively, against the mobilities of [110]-surface unstrained MOSFETs. As a result, the electron and the hole mobility ratios of [110]-surface strained-SOI MOSFETs to the universal mobility of (100)-surface bulk-MOSFETs increase up to 81% and 203%, respectively. Therefore, the current drive imbalance between n- and p-MOS can be reduced. Moreover, both the electron and the hole mobilities of the [110]-surface strained-SOIs strongly depend on the drain current flow direction, which is qualitatively explained by the anisotropic effective mass characteristics of the carriers on a [110]-surface Si. As a result, the [110]-surface strained-SOI technology with optimization of the current flow directions of n- and p-MOS is promising for realizing higher speed scaled CMOS.     

Improved direct bonding method of Nd:YVO4 and YVO4 laser crystals

We succeeded in the fabrication of bonded laser crystals composed of a neodymium-doped YVO₄ laser crystal (Nd:YVO₄) and its host crystals YVO₄ by a newly developed dry etching technique using an argon ion beam. The optical distortion caused by the bonded interface of size 5 mm × 6 mm was estimated to be 0.05λ at 633 nm. From the comparison of laser performance pumped by a laser diode, the bonded crystals could increase the laser output power by nearly twice that of the non-bonded crystals with the same degree of polarization of 99.2%. To analyze the mechanism of the enhanced reduction of the thermal load in the bonded crystals, numerical simulations with a finite-element method were also performed.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Effect of ecabet sodium on Helicobacter pylori adhesion to gastric epithelial cells

STUDY OBJECTIVES: To determine the rates of alcohol-related morbidity and mortality in a cohort of intoxicated ED patients 5 years after presentation and to compare them with those of non-intoxicated ED patients. METHODS: The study group comprised 150 consecutive ED patients who presented with intoxication (blood alcohol level higher than 100 mg/dL) in June 1986 and 50 control patients matched for age, sex, ED arrival time, and date. The setting was an urban university hospital ED. Morbidity and mortality over a 5-year follow-up period were measured using hospital ED and admission records from all state Level I trauma centers and computerized statewide databases. RESULTS: The 5-year mortality rate among alcohol-intoxicated patients was 2.4 times that of the comparison group (95% confidence interval, .3 to 18.9). The 5-year death rate among intoxicated patients aged 40 to 69 years was especially high (19%). Thirty-seven percent of the intoxicated patients made at least one alcohol-related ED revisit during the follow-up period, compared with 6% of the comparison group (P < .001). Intoxicated patients were more likely to revisit EDs because of suicidal behavior or domestic violence (P = .001). Admission to an alcohol detoxification unit during the follow-up period occurred in 24% of the intoxicated patients, compared with 10% of the sober controls (P = .03). At least one arrest for drunk driving occurred in 47% of the intoxicated group; the rate was lower, but still substantial, in the comparison group (20%, P < .001). CONCLUSION: A single alcohol-related ED visit is an important predictor of continued problem drinking, alcohol-impaired driving and, possibly, premature death.     

Influence of third monomer on the crystal phase transition behavior of ethylene-tetrafluoroethylene copolymer

Crystal phase transition between the low- and high-temperature phases has been investigated for ethylene (E)-tetrafluoroethylene (TFE) alternating copolymer (ETFE) containing the third monomeric species by the temperature dependent measurements of wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) and differential scanning calorimetry. Nonafluoro-1-hexene (NFH) and hexafluoropropylene (HFP) were chosen as the third monomers, where they are different in the side-branch length, -(CF₂)₃CF₃ and -CF₃, respectively. In the case of E/TFE/NFH copolymer (ET-C4F9), the crystal phase transition temperature of the original ETFE two-components copolymer was not very much affected by the existence of NFH in the range of NFH content from 0.7 to 3 mol%. Contrarily, the crystal phase transition temperature of E/TFE/HFP copolymer (ET-CF3) was found to decrease drastically with increasing HFP content. The melting temperature and the higher-order structure were also affected sensitively depending on the HFP content. This difference in phase transition behavior between ET-C4F9 and ET-CF3 copolymers is reasonably interpreted as follows: the short side groups (-CF₃) of HFP monomeric unit are included in the crystal lattice of E/TFE chains and the unit cell is expanded gradually with an increment of the HFP content, resulting in the decrease in phase transition point because of easier thermal motion of the chains. On the other hand, the long side groups [-(CF₂)₃CF₃] of NFH monomeric units are excluded out of the crystal lattice and located on the lamellar surfaces or in the amorphous region and do not affect very much the phase transition temperature even when the NFH content is increased. In association with such a change in crystal structure, the long period of stacked lamellar structure was found to decrease remarkably in the case of NFH, whereas it does not change very much for HFP, consistent with the interpretation of the above-mentioned WAXD data.     

Responses of plasma norepinephrine and heart rate during exercise in patients after Fontan operation and patients with residual right ventricular outflow tract obstruction after definitive reconstruction

In a fetal autopsy series, we have explored the occurrence of renal tubular dysgenesis in twins. Renal tubular dysgenesis was found exclusively among those monozygotic twins with evidence of twin transfusion syndrome, particularly in those donor twins with oligohydramnios and growth restriction. We infer that hypotension in the donor twin of the twin transfusion syndrome pair is responsible for the failure of proximal convoluted tubule differentiation, and the disturbance of renal function is manifested as oligohydramnios prenatally, and either oliguria or tubular dysfunction postnatally.     

The combined method: a novel access technique for fetal endoscopic surgery

BACKGROUND/PURPOSE: To develop practical and less invasive techniques for fetal endoscopic surgery, new methods of lifting the uterine wall to allow fetal surgery without maternal laparotomy were developed and assessed. METHODS: Fetal endoscopic surgical procedures, including tracheostomy and umbilical vascular cannulation, were performed using one of the three methods to enter the uterus without maternal laparotomy in pregnant goats (n = 6; 105 to 115 days' gestation): (1) direct uterine lifting with an air-cushion device; (2) indirect uterine lifting, in which the uterine wall was fixed to the maternal abdominal wall using balloon tip ports inserted percutaneously by Seldinger's method, then the maternal abdomen was lifted mechanically; and (3) combined method, in which low pressure CO2 (5 mm Hg for initial inflation and 2 mm Hg for maintenance) was insufflated into the uterus in addition to the indirect uterine lifting cited above. RESULTS: The direct uterine lifting caused massive injury of myometrium and uterine membranes. The creation of intrauterine space and the protection of the membranes were not accomplished effectively by the indirect uterine lifting only. The combined method provided the adequate intrauterine space and excellent endoscopic visibility for completion of the endoscopic procedures with minimal uterine injury. CONCLUSION: The fetal endoscopic surgery may be accomplished simply and safely by the combined method, a novel technique of uterine lifting to allow fetal surgery without maternal laparotomy.