Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

An interactive multiple-response simulation optimization method

This study proposes a new interactive multicriteria method for determining the best levels of the decision variables needed to optimize a stochastic computer simulation with multiple response variables. The method, called the Pairwise Comparison Stochastic Cutting Plane (PCSCP) method, combines good features from interactive multiple objective mathematical programming and response surface methodology. The major characteristics of the PCSCP method are: (1) it interacts progressively with the decision-maker (DM) to obtain her preferences, (2) it uses experimental design to explore the decision space adequately while reducing the burden on the DM, and (3) it uses the preference information provided by the DM and the sampling error in the responses to reduce the decision space. The mechanics of the method are illustrated with a numerical example. Some computational studies evaluating the method are also reported.     

Parasitic Bipolar Junction Transistors in a Floating-Gate MOSFET for Fluorescence Detection

In this letter, we examined whether the parasitic bipolar junction transistors (BJTs) in the MOSFET fabricated by the standard CMOS process can play a role as a fluorescence detector. To suppress the action of two vertical parasitic BJTs, the gate and n-well were tied in the parasitic BJTs, and the body node was connected to the drain. The proposed device was compared with the inherent and the parasitic diodes in the MOSFET. It had 100 times higher photocurrents than the diodes in the MOSFET. In addition, it was applied for the detection of the fluorescent signal, and could detect near 10 nM of Alexa 546. Therefore, CMOS-process-compatible parasitic BJTs can be used as a photodetector in an integrated fluorescence detector.     

Robust Geodesic Regression

International Journal of Computer Vision - This paper studies robust regression for data on Riemannian manifolds. Geodesic regression is the generalization of linear regression to a setting with a...     

Development of a sequential robust–tolerance design model for a destructive quality characteristic

Robust design (RD) and tolerance design (TD) have received much attention from researchers and practitioners for more than two decades, and a number of methodologies for modeling and optimizing the RD and TD processes have been studied. However, there is ample room for improvement. Because most existing research considers RD and TD as separate research fields, the primary objective of this paper is to develop a sequential robust–tolerance design method to jointly determine the best factor settings and the closed-form solutions for the optimal specification limits. We then apply the proposed method to a destructive quality characteristic. Finally, a case study and sensitivity analyses are performed for verification purposes, and further studies are discussed.     

Fabrication of Er3+/Pr3+ Co-doped soda-lime glass thin films using RF magnetron sputtering method and optical property characterization

Er^3+/Pr³⁺ co-doped soda-lime glass thin films have been fabricated using RF magnetron sputtering method and their structural and optical properties have been studied. Deposition rate, crystallinity, and composition of glass thin films were investigated by scanning electron microscopy, transmission electron microscopy, and electron probe micro area analysis. Refractive index, birefringence and binding characteristics have been investigated using a prism coupler and X-ray photoelectron spectroscopy. Er³⁺/Pr³⁺ co-doped soda lime glass thin films were prepared by changing substrate temperature (room temp. ∼550^∘C), RF power (90 W–130 W), and Ar/O₂ gas flow ratio at processing pressure of 4 mTorr. Glass thin films could be obtained at the optimized processing condition at 350^∘C, RF power of 130 W, and gas flow of Ar:O₂ = 40:0 with maximum deposition rate of 1.6 μm/h. Refractive index and birefringence increased from 1.5614 to 1.5838 and from 0.000154 to 0.000552, respectively, as the content of Pr³⁺ increased. Binding energy of Pr3d also increased as the content of Pr³⁺ increased.     

ANALYSIS OF THREE-DIMENSIONAL MACHINING USING AN EXTENDED OBLIQUE MACHINING THEORY

This paper presents an extended oblique machining theory applicable to the analysis of 3-D machining. Existing theories are evaluated to identify suitable formulations which are used with necessary modifications for predicting various quantities pertaining to cutting conditions of three dimensional machining. Actual chip flow angles extracted from measured forces, to account for the nose radius effect, are used, instead of available models, to predict important quantities such as shear plane angle, effective rake angle and shear flow angle. Experiments are conducted in the realms of conventional and high speed machining using AISI 4140 steel and aluminum 7075-T6 respectively with uncoated carbide inserts, and various process conditions pertaining to the cutting mechanics are calculated. The extended oblique machining theory is experimentally validated in predicting temperatures at the tool-chip interface and shear plane for conventional machining. Simulation results from the finite element modeling are used for verifying the shear stress and shear plane temperature predicted by the extended oblique machining theory.     

Procedural Synthesis using Vortex Particle Method for Fluid Simulation

We propose a fast and effective technique to improve sub‐grid visual details of the grid based fluid simulation. Our method procedurally synthesizes the flow fields coming from the incompressible Navier‐Stokes solver and the vorticity fields generated by vortex particle method for sub‐grid turbulence. We are able to efficiently animate smoke which is highly turbulent and swirling with small scale details. Since this technique does not solve the linear system in high‐resolution grids, it can perform fluid simulation more rapidly. We can easily estimate the influence of turbulent and swirling effect to the fluid flow.     

Rayleigh waves in magneto-thermoelastic solids with thermal relaxation

Following a linear theory of magneto-thermo-elasticity with thermal relaxation, the propagation of Rayleigh waves in a semi-infinite body permeated by an uniform magnetostatic field parallel to the boundary surface is investigated. It is assumed that the elastic medium under consideration is a homogeneous, isotropic, electrically and thermally conducting one. The roots of the frequency equation are calculated numerically. The approximate solution for small thermoelastic and magnetoelastic coupling is obtained and compared with the exact solution.