Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Highly reliable a‐IGZO TFTs on a plastic substrate for flexible AMOLED displays

We have successfully reduced threshold voltage shifts of amorphous In–Ga–Zn–O thin‐film transistors (a‐IGZO TFTs) on transparent polyimide films against bias‐temperature stress below 100 mV, which is equivalent to those on glass substrates. This high reliability was achieved by dense IGZO thin films and annealing temperature below 300 °C. We have reduced bulk defects of IGZO thin films and interface defects between gate insulator and IGZO thin film by optimizing deposition conditions of IGZO thin films and annealing conditions. Furthermore, a 3.0‐in. flexible active‐matrix organic light‐emitting diode was demonstrated with the highly reliable a‐IGZO TFT backplane on polyimide film. The polyimide film coating process is compatible with mass‐production lines. We believe that flexible organic light‐emitting diode displays can be mass produced using a‐IGZO TFT backplane on polyimide films.     

Kinetics of the methanation of carbon dioxide over a supported Ni-La2O3 catalyst

The kinetics of the methanation of carbon dioxide was investigated using an alumina supported Ni-La₂O₂ catalyst in a differential and integral reactor. In the differential reactor the molar ratio of H₂ to CO₂ was varied from 0.6 to 30. In the integral reactor the rates were measured with up to 90% conversion. Both reactor tests were carried out at temperatures between 513 and 593 K. The experimental results were described by a Langmuir-Hinshelwood type equation. The kinetics can be explained by assuming equilibrium of dissociative carbon dioxide and hydrogen adsorption, and assuming hydrogenation of surface carbon as the rate determining step.     

Preparation of π-conjugated polymers consisting of 2-decylbenzimidazole and thiophene units and chemical properties of the polymers

Polycondensation by Stille coupling of 2-decyl-4,7-dibromobenzimidazoles and N-methyl-2-decyl-4,7-dibromobenzimidazole with 2,5-bis(trimethylstannyl)thiophene and 5,5′-bis(trimethylstannyl)-2,2′-bithiophene gave the corresponding π-conjugated polymers, poly(2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 1b, poly(2-decylbenzimidazole-4,7-diyl-bithiophene-2,5-diyl) 1c and poly(N-methyl-2-decylbenzimidazole-4,7-diyl-thiophene-2,5-diyl) 2b, in 98-99% yields. The polymers 1b and 2b were fully soluble in CF₃COOH, and partially soluble in DMF (about 60 and 40% for 1b and 2b, respectively) and NMP (about 70 and 40%, respectively). The NMP soluble part of 1b and DMF soluble part of 2b gave values of 0.36 and 0.24 dl g⁻¹ in NMP and DMF, respectively. The DMF soluble part of 1b, 1c and 2b showed absorption peaks at about 458, 465 and 388 nm, respectively, in DMF. In an alkaline medium the absorption peaks of 1b and 1c are shifted to a longer wavelength by 92-101 nm; the observed shifts in the acidic medium and alkaline medium were much larger than those observed with usual benzimidazoles with low molecular weights. Packing structures of 1b, 1c and 2b are discussed based on their XRD patterns.     

Phase evolution and <110>-orientation mechanism in RTGG-processed BaTiO3 ceramics with electrical properties

The <110>-oriented BaTiO₃ ceramics were fabricated using BaCO₃ matrix and H_1.08Ti_1.73O₄.nH₂O (HTO) template particles, and the mechanism of BaTiO₃ phase formation was investigated. The dielectric, ferroelectric, and piezoelectric properties were also investigated. The transformation of the HTO phase into the TiO₂ bronze or TiO₂ (B) phase was observed at 600°C, where the BaTiO₃ nucleation was accompanied by the formation of a Ba₂TiO₄ phase. The TiO₂ phase reacted with the Ba₂TiO₄ phase at 800°C to give a BaTiO₃ phase, whereas its reaction with the BaTiO₃ resulted in the formation of BaTi₂O₅ phase that got decomposed into BaTiO₃ and Ba₆Ti₁₇O₄₀ phase at sintering temperature ≥1300°C. Sintering with samples’ embedding in BaTiO₃ powders prevented the formation of the Ba₆Ti₁₇O₄₀ secondary phase. The crystallographic orientation along the <110> direction (F₁₁₀) was developed by the epitaxial grain growth mechanism. In addition to the contribution of the grain-size increment for enhancing the F₁₁₀, the preservation of the platelike structure was also found to have a significant impact. The ceramics prepared by the embedded sintering (grain size ≈12.4 µm and F₁₁₀ = 83%) exhibited the room-temperature dielectric constant of 1708 and piezoelectric strain constant of 445 pm/V, which are higher than those of the BaTiO₃ ceramics with randomly oriented grains.     

A novel radial orientation treatment of nematic liquid crystals using magnetic field lines with permanent magnet and applying the assisted electric field

Recently, there has been considerable research on optical devices, such as liquid crystal (LC) lenses and special optical plates, using LCs. In such devices, relatively small LC cells are frequently used, or unique LC orientations are required. As an LC orientation process, we focused on the LC director's orientation induced by the magnetic force line distribution of a small neodymium magnet. We propose a simple method for obtaining radial orientation, which is rather difficult to obtain using the ordinary rubbing method. The initial orientation in the LC cell is a vertical orientation cell with almost zero azimuth anchoring. With the proposed method, the reorientation process is performed with an assisting electric field and a small permanent magnet, unlike the conventional magnetic field orientation process that requires a large electromagnet. Furthermore, a polymer stabilization treatment is used to fix the obtained radial orientation pattern in the LC cell. After the treatment, the applying voltage can control the tilt angle of the director in weak polymer treatment, and a completely fixed orientation pattern can be obtained that in strong.     

Stick-slip motion control based on cutter location data for an orthogonal-type robot

In this article, a new desktop orthogonal-type robot, which has the capacity of stick-slip motion control based on cutter location data, is presented for lapping small metallic molds with a curved surface. The robot consists of three single-axis devices with a high position resolution of 1 μm. A thin wooden stick tool with a ball-end shape is attached to the tip of the z-axis. In order to improve the lapping performance, a novel stick-slip motion control method is developed in the control system. The small stick-slip motion is orthogonally generated in the direction of the tool’s movement. The effectiveness of stick-slip motion control is examined through an actual lapping test of an LED lens cavity.     

Recurrent infomax generates cell assemblies, neuronal avalanches, and simple cell-like selectivity

Recently multineuronal recording has allowed us to observe patterned firings, synchronization, oscillation, and global state transitions in the recurrent networks of central nervous systems. We propose a learning algorithm based on the process of information maximization in a recurrent network, which we call recurrent infomax (RI). RI maximizes information retention and thereby minimizes information loss through time in a network. We find that feeding in external inputs consisting of information obtained from photographs of natural scenes into an RI-based model of a recurrent network results in the appearance of Gabor-like selectivity quite similar to that existing in simple cells of the primary visual cortex. We find that without external input, this network exhibits cell assembly-like and synfire chain-like spontaneous activity as well as a critical neuronal avalanche. In addition, we find that RI embeds externally input temporal firing patterns to the network so that it spontaneously reproduces these patterns after learning. RI provides a simple framework to explain a wide range of phenomena observed in in vivo and in vitro neuronal networks, and it will provide a novel understanding of experimental results for multineuronal activity and plasticity from an information-theoretic point of view.