Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Photochemical identification of transmembrane segment IVS6 as the binding region of semotiadil, a new modulator for the L-type voltage-dependent Ca2+ channel

To identify the binding domain of a new Ca2+ antagonist semotiadil on L-type Ca2+ channels from skeletal muscle, photolabeling was carried out by using an azidophenyl derivative of [3H]semotiadil. Photoincorporation was observed in several polypeptides of membrane triad preparations; the only specific photoincorporation was in the alpha1 subunit of the Ca2+ channel. After solubilization and purification, the photolabeled alpha1 subunit was subjected to proteolytic and CNBr cleavage followed by antibody mapping. Specific labeling was associated solely with the region of transmembrane segment S6 in repeat IV. Quantitative immunoprecipitation was found in the tryptic and the Lys-C/Glu-C fragments of 6.6 and 6.1 kDa, respectively. Further CNBr cleavage of the Lys-C digests produced two smaller fragments of 3.4 and 1.8 kDa that were included in the tryptic and Lys-C/Glu-C fragments. The smallest labeled fragments were: Tyr1350-Met1366 and Leu1367-Met1381 containing IVS6, a possible pore-forming region. The data suggest that semotiadil binds to a region that is overlapped with but not identical to those for phenylalkylamines, dihydropyridines and benzothiazepines. The present study also provides evidence that region IV represents an important component of a binding pocket for Ca2+ antagonists.     

Rates for intramolecular excimer formation of poly(α-methylstyrene) measured by using picosecond pulse radiolysis

Summary The rate constants for intramolecular excimer formation, k_DM, of poly(α-methylstyrene) with different molecular weight were determined by using picosecond pulse radiolysis. Values of k_DM for poly(α-methylstyrene) are a little smaller than those for polystyrene with nearly same molecular weight. It appears to be mainly due to steric hindrance by methyl substituent of main chain.     

Temperature measurements of polymer melts in the heating barrel during injection molding. Part I. Temperature distribution along the screw axis in the reservoir

A new procedure has been developed to measure the temperature distribution of the polymer melts along the screw axis during injection by using a small sheath thermocouple. At the same time, the effects of molding conditions on temperature distribution has been studied. The temperature distribution of the polymer melt along the screw axis during injection can be obtained from the difference between the standard temperature profile and the temperature profile of the polymer melt with unknown and non-uniform temperature measured under the same rate of injection. The temperature of a polymer melt within a shot is not uniform. The difference between the maximum and the minimum temperature within a shot may exceed 10°C in some cases. There are two major factors which govern the effects of molding conditions on the temperature distribution of the polymer melts during injection. The first is the amount of shear heating in the metering zone. The second is the amount of heat absorbed into the polymer in the compression and feed zones.     

Control of the electron temperature by varying the resonance zone width in ECR plasma

The electron temperature (T_e) in an electron cyclotron resonance plasma is clarified to depend on the spatial profiles of the microwave-power absorption by both the electromagnetic-waves measurement and the simulation of microwave power absorption. It is found that T_e is controlled by varying the magnetic field configuration and/or the microwave frequency since the power absorption profile is influenced by the effective resonance width. In fact, T_e is observed to decrease with decreasing the magnetic field gradient at the resonance point for N₂, Ar and O₂/Ar plasma.     

Structures of spider toxins: hydroxyindole-3-acetylpolyamines and a new generalized structure of type-E compounds obtained from the venom of the Joro spider, Nephila clavata

Facile structure determination of acylpolyamines, glutamatergic nerve blocker obtained from the venom of the Joro spider (Nephila clavata) was carried out with the use of micro-column LC/MS and high energy collision induced dissociation (CID) mass spectrometry. 6-hydroxyindole-3-acetyl was proposed previously as a putative partial structure, for the acyl moiety of hydroxyindole-type polyamines (NPTX-1 to -6). The NMR data obtained for NPTX-6, NPTX-687 and hydroxyindole-3-acetic acid which was released by acid hydrolysis of Nephila clavata crude venom extracts proved that the lipophilic head is the 4-hydroxyindole-3-acetic acid. Various hydroxyindole-3-acetyl polyamines were found in N. Clavata venom and characterized by mass spectrometry. As a result, type-E, a new class of generalized acylpolyamine structure was proposed in addition to the previously reported polyamine backbones type-A to -D.     

Application of wavelet transform for extracting edges of paddy fields from remotely sensed images

For geographical information systems (GIS) to be useful in the management of Japanese paddy fields, it is vital to be able to prepare base maps that define sections of field. We attempted to prepare a base map by detecting the edges of submerged paddy fields from a SPOT image with the use of multi-resolution wavelet transform. The raw image of SPOT band 3 was decomposed into a low frequency approximation image and a set of high frequency detailed images to five levels, and then reconstructed. The reconstructed image at the fifth level was obtained from all of the high frequency images except for the low frequency approximation image. The image reconstructed up to full scale was then applied to a zero-crossing scheme and three post-processings—line thinning, removal of isolated pixels, and connection of pixels with their neighbours—in order to obtain clear edges. The spatial features of the image indicating the edges obtained by multi-resolution wavelet transform were compared quantitatively with those obtained by using a difference of Gaussian (DOG) filter. The multi-resolution wavelet transform was better than the DOG filter in that the base map obtained by the wavelet transform method represented a ‘field block’, which is typically composed of 10 holdings of paddy field, more precisely than with the DOG filter, and in that the number of open polygons on this map was smaller, indicating that the wavelet transform method is more suitable for producing the base map in GIS for the management of paddy fields.