Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

Analytical Modeling of Surface Potential and Drain Current of Hetero-Dielectric DG TFET and Its Analog and Radio-Frequency Performance Evaluation

Semiconductors - In the present paper, analytical modeling of surface potential and drain current for hetero-dielectric double gate tunnel FET (HDG-TFET) has been done. The two dimensional (2D)...     

A prospective study of closure techniques of abdominal incisions in infants and children

In a prospective study of layered versus mass closure of abdominal incisions in infants and children, 34 cases underwent wound closure by layered and mass closure technique on an alternate basis. All the patients were assessed for their nutritional status and haemoglobin level pre-operatively, and wound complications were compared with respect to closure technique, nutritional status and normal haemoglobin level. Presence of protein energy malnutrition and anaemia did not increase the risk of wound complications with either of the technique.     

Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.     

Analysis of a soliton-based logic module for a ring network

We analyze and numerically study the code-matching logic module that is the central element in a proposed soliton-based ring network system running at peak rates of 100 Gb/s. The proposed network is packet-switched, and fast logic is required to route each packet. That is the function of the code-matching logic module, and four soliton logic gates that can perform fast logic are the key devices in its design. The behavior of the code-matching logic module is governed by a large set of parameters, and we simulate it by varying many of these parameters. The physical effects that occur in these devices and their significance are analyzed. The results indicate that the logic module will work but within a restricted parameter range     

Structural and electrical measurements of CdZnSe composite

TheI—Vcharacterization and the electrical resistivity of selenium rich Se₈₅Cd_15-xZn_x (x = 0, 3, 7, 11 and 15) system at room temperature have been studied. Samples were obtained using melt cooling technique. So prepared samples were then characterized in terms of their crystal structure and lattice parameter using X-ray diffraction method. The materials were found to be poly crystalline in nature, having zinc blend structure over the whole range of zinc concentration. The measurements ofI—V bdcharacteristics have been carried out at different temperatures from room to 140°C. The electrical resistivity of the samples with composition at room temperature has been found to vary between maximum 2.7 x 10⁸ Ωm and minimum 7.3 x 10⁵ Ωm and shows a maximum at 3 at. wt.% of Zn. The carrier activation energy of the samples with composition has also been determined and found to vary from 0.026 eV to 0.111 eV.