Preparation of SiC particles coated with alumina hydrate: Effect of reaction condition on particle coalescence

Alumina-hydrate-coated SiC particles were prepared via a homogeneous precipitation method using urea, and the conditions for uniform coating and less coalescence of the particles were investigated. Coalescence of coated particles could be said to occur by collision and agglomeration followed by deposition of alumina hydrate on the agglomerated particles. Coalescence of coated particles was suppressed by use of low reaction temperature, low concentration of aluminium sulfate, high concentration of urea, intensive stirring, and a flow reactor.     

Evaluation of advanced fuzzy logic PSS on analog network simulatorand actual installation on hydro generators

This paper presents the experimental evaluation of an advanced fuzzy logic PSS on the analog network simulator at the Research Laboratory of Kyushu Electric Power Co., Inc. The proposed power system stabilizer (PSS) is set up by using a personal computer with A/D and D/A conversion interfaces. The personal computer based PSS was set on the analog network simulator to evaluate the effectiveness of the advanced fuzzy logic control scheme, and to provide sufficient data for the actual installation of the proposed PSS on hydro-units in the Kyushu Electric Power System. This paper also describes the actual installation of the proposed PSS on hydro-units in the Kyushu Electric Power System for the long term evaluation of the proposed PSS using its prototypes     

Development of 170 GHz/500 kW gyrotron

A development of 170GHz/500kW level gyrotron was carried out as R&D work of ITER. The oscillation mode is TE_31,8. In a short pulse experiment, the maximum power of 750kW was achieved at 85kV/40A. The efficiency was 22%. In the depressed collector operation, 500kW/36%/50ms was obtained. The maximum efficiency of 40% was obtained at P_RF=470kW whereas the power decrease by the electron trapping was observed. Pulse extension was done up to 10s at P_RF=170kW with the depressed collector operation. The power was limited by the temperature increase of the output window.     

Experimental study on a quasi-optical mode converter for transforming the whispering-gallery mode into a circularly polarized hollow radiation beam

An experiment was carried out for transforming the 120 GHz-TE_12.2 whispering-gallery mode (WGM) into a circularly polarized hollow radiation beam. A hollow beam was formed by reflecting the WGM, which was radiated from a 16 mm radius circular waveguide cut, with an annular mirror having suitable local normal vectors. The experimentally observed field intensity profiles of the reflected wave were in good agreement with calculated results.     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.     

On the modelling of scalar and mass transport in combustor flows

The results of a numerical study of swirling and non-swirling combustor flows with and without density variations are presented. Constant-density arguments are used to justify closure assumptions invoked for the transport equations for turbulent momentum and scalar fluxes, which are written in terms of density-weighted variables. Comparisons are carried out with measurements obtained from three different axisymmetric model combustors. The three experiments cover recirculating flow, swirling flow and variable-density, swirling flow inside model combustors. Together, they offer wide ranging flow conditions to test the validity of the models. Results show that the Reynolds stress/flux models do a credible job of predicting constant-density, swirling and non-swirling combustor flows with passive scalar transport. However, their improvements over algebraic stress/flux models are marginal. The extension of the constant-density models to variable-density flow calculations shows that the models are equally valid for such flows. Therefore, the present results argue well for the adoption of constant-density models for variable-density flows until a successfully validated variable-density model is available.     

Effects of brefeldin-A on Golgi morphology in human cultured fibroblasts observed in three-dimensional stereo scanning electron microscopy

Brefeldin A (BFA) has been reported to cause disassembly of the Golgi. We have used three-dimensional (3-D) high-resolution scanning electron microscopy (HRSEM) to investigate these effects in human skin fibroblast cells. The spontaneous reassembly during prolonged exposure to BFA and some effects of forskolin were observed. A BFA concentration of 5μg/ml caused Golgi complexes to become vesicular, resulting in a progressive decrease in the size of the Golgi. Morphologic changes were visible within 2 min of BFA incubation, and by 30 min no identifiable Golgi could be found. Spontaneous reassembly of the Golgi apparatus upon the removal of the BFA or with continued long-term exposure with BFA could not be confirmed. Preliminary experiments with forskolin were not effective in reversing or inhibiting the effects of BFA in human fibroblast cells grown in culture. This inability for spontaneous reassembly and nonreversal by forskolin may reflect a differential effect of BFA in various cell types. HRSEM has proven to be useful for observing 3-D morphologic effects of BFA in Golgi.     

Photodegradation mechanism and stabilization of polyphenylene oxide and rigid‐rod polymers

Poly(2,4‐dimethyl‐1,4‐phenylene oxide) (PPO), poly(benzo[1,2‐d:5,4‐d′]bisoxazole‐2,6‐diyl‐1,4‐phenylene) (PBO) and poly(benzo[1,2‐d:4,5‐d′]bisthiazole‐2,6‐diyl‐1,4‐phenylene) (PBZT), which are polymers with extended conjugated structures, undergo a self‐sensitized photo‐induced electron‐transfer reaction. A second component is not required. This article presents many similar observations on these polymers when they are exposed to light and evidence to support the proposed photo‐induced electron‐transfer mechanism. Methods to stabilize these polymers against photo‐oxidation are also described. Workers investigating other conjugated polymeric systems may find the experimental methods, observations and polymer stabilization approaches discussed in this review useful. Copyright © 2005 Society of Chemical Industry