Electrocatalytic Reduction of CO2 to Ethylene by Molecular Cu‐Complex Immobilized on Graphitized Mesoporous Carbon

The electrochemical reduction of carbon dioxide (CO₂) to hydrocarbons is a challenging task because of the issues in controlling the efficiency and selectivity of the products. Among the various transition metals, copper has attracted attention as it yields more reduced and C2 products even while using mononuclear copper center as catalysts. In addition, it is found that reversible formation of copper nanoparticle acts as the real catalytically active site for the conversion of CO₂ to reduced products. Here, it is demonstrated that the dinuclear molecular copper complex immobilized over graphitized mesoporous carbon can act as catalysts for the conversion of CO₂ to hydrocarbons (methane and ethylene) up to 60%. Interestingly, high selectivity toward C2 product (40% faradaic efficiency) is achieved by a molecular complex based hybrid material from CO₂ in 0.1 m KCl. In addition, the role of local pH, porous structure, and carbon support in limiting the mass transport to achieve the highly reduced products is demonstrated. Although the spectroscopic analysis of the catalysts exhibits molecular nature of the complex after 2 h bulk electrolysis, morphological study reveals that the newly generated copper cluster is the real active site during the catalytic reactions.     

Selection of network and learning parameters for an adaptive neural robotic control scheme

This paper presents the results of a study in the design of a neural network based adaptive robotic control scheme. The neural network used here is a two hidden layer feedforward network and the learning scheme is the well-known backpropagation algorithm. The neural network essentially provides the inverse of the plant and acts in conjunction with a standard PD controller in the feedback loop. The objective of the controller is to accurately control the end position of a single link manipulator in the presence of large payload variations, variations in the link length and also variations in the damping constant. Based on results of this study, guidelines are presented in selecting the number of neurons in the hidden layers and also the parameters for the learning scheme used for training the network. Results also indicate that increasing the number of neurons in the hidden layer will improve the convergence speed of learning scheme up to a certain limit beyond which the addition of neurons will cause oscillations and instability. Guidelines for selecting the proper learning rate, momentum and fast backpropagation constant that ensure stability and convergence are presented. Also, a relationship between the r.m.s. error and the number of iterations used in training the neural network is established.     

ESD–RF co-design methodology for the state of the art RF-CMOS blocks

This paper describes an approach to design ESD protection for integrated low noise amplifier (LNA) circuits used in narrowband transceiver front-ends. The RF constraints on the implementation of ESD protection devices are relaxed by co-designing the RF and the ESD blocks, considering them as one single circuit to optimise. The method is applied for the design of 0.25 μm CMOS LNA. Circuit protection levels higher than 3 kV HBM stress are achieved using conventional highly capacitive ggNMOS snapback devices. The methodology can be extended to other RF-CMOS circuits requiring ESD protection by merging the ESD devices in the functionality of the corresponding matching blocks.     

Effects of flux enhancing polymer on the characteristics of sludge in membrane bioreactor process.

A newly developed membrane performance enhancer (MPE) was used to prevent membrane fouling in a membrane bioreactor (MBR) process. It transpired that 1,000 mg/l of MPE reduced polysaccharide levels from 41 mg/I to 21 mg/I on average under the experimental condition. Repeated experiments also confirmed that 50-1,000 mg/l of MPE could reduce membrane fouling significantly and increase the intervals between membrane cleanings. Depending on MPE dosages and experimental conditions, trans-membrane pressure (TMP) increase was suppressed for 20-30 days, while baseline TMP surged within a few days. In addition, MPE allowed MBR operation even at 50,000 mg/l of total solid and reduced permeate COD. However, no evidence of toxicity for sludge was found from respiratory works.     

Intraoperative neurological monitoring

Intraoperative neurological monitoring (INM) is the evaluation of the nervous system within the operating room (OR) environment. In this paper, the INM system is tested in a clinical setting in comparison with conventional somatosensory evoked potential (SEP) monitoring. The study results demonstrate the capability of the INM system in extracting clearer and more stable SEP signals. The high SNR of SEP signals collected in various clinical environments, including the OR, makes the INM system a robust platform for continuous monitoring. While the current use of EP monitoring is limited to intermittent analysis by a highly trained clinical neurophysiologist, the authors believe in changing this paradigm by developing continuous monitoring systems, such as the INM system, capable of automated quantitative EP analysis. This noninvasive monitoring modality will allow for a wider range of use in clinical practice. Based on volunteer and clinical patient studies, the INM monitoring system demonstrates much greater reliability and accuracy via the artifact rejection and denoising strategies. It provides more strategic filtering options for different situations under which the clinical SEP response signal could be greatly contaminated and distorted. Furthermore, the INM system offers a promising approach to signal extraction in real-time monitoring during SEP research.     

Prototype test on X-bracing panels using cold-formed lipped angles

The behavior and suitability of cold-formed lipped angle members for X-bracing with redundant have been studied. For the purpose, two full-scale panel tests were carried out. The first panel was designed so that the compression member would fail by buckling in flexural mode and the second panel in flexural-torsional mode. The members were designed using ASCE Manual No. 52. Theoretical aspects of least radius of gyration and buckling behavior of this bracing system have been discussed. The investigation on first panel, revealed that the member would buckle only in the flexural-torsional mode although flexural buckling would govern the design. The second panel test result showed that, the buckling mode and strength of the system for lipped angle sections can be predicted reasonably well.