A new write/erase method to improve the read disturbcharacteristics based on the decay phenomena of stress leakage currentfor flash memories

This paper describes a new write/erase method for flash memory to improve the read disturb characteristics by means of drastically reducing the stress leakage current in the tunnel oxide. This new write/erase operation method is based on the newly discovered three decay characteristics of the stress leakage current. The features of the proposed write/erase method are as follows: 1) the polarity of the additional pulse after applying write/erase pulse is the same as that of the control gate voltage in the read operation; 2) the voltage of the additional pulse is higher than that of a control gate in a read operation, and lower than that of a control gate in a write operation; and 3) an additional pulse is applied to the control gate just after a completion of the write/erase operation. With the proposed write/erase method, the degradation of the read disturb life time after 10⁶ write/erase cycles can be drastically reduced by 50% in comparison with the conventional bipolarity write/erase method used for NAND type flash memory. Furthermore, the degradation can he drastically reduced by 90% in comparison with the conventional unipolarity write/erase method fur NOR-, AND-, and DINOR-type flash memory. This proposed write/erase operation method has superior potential for applications to 256 Mb flash memories and beyond     

Crystal orientation of β-phase isotactic polypropylene induced by magnetic orientation of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide

Melt crystallization of isotactic polypropylene (iPP), containing crystallites of N,N′-dicyclohexyl-2,6-naphthalenedicarboxamide (DCNDCA) as a nucleating agent of the the β-phase iPP crystal, is carried out under a magnetic field (6 T) to obtain the alignment of the iPP crystal induced by magnetic alignment of DCNDCA. In a previous paper, DCNDCA was reported to undergo magnetic alignment in a liquid suspension. The obtained iPP sample exhibits alignment of the β-phase crystal with the c-axis aligned perpendicular to the magnetic field. The comparison of this alignment of iPP with the reported magnetic alignment of DCNDCA indicates that the β-phase crystal grows epitaxially on the DCNDCA crystal. The (330)_β plane of the iPP crystal lies on the bc-plane of the DCNDCA crystal in which the direction of the c-axis of the iPP coincides with the direction of the b-axis of the DCNDCA crystal.     

Fracture toughness measurement with fatigue-precracked single edge-notched beam specimens of WC-Co hard metal

The plain-strain fracture toughness of WC-8%Co hard metal, K _IC, was measured using single edge-notched beam (SENB) specimens with fatigue precrack. The fatigue precrack was introduced with compressive fatigue cycling in four-point bending at room temperature. Since stable fatigue-crack propagation was obtained from the notch tip, it was easy to control the fatigue-precrack length. A reasonable K _IC value of 13.3 MPa m^1/2 was obtained with the fatigue-precracked SENB specimens in four-point bending. The compressive fatigue-precracking technique in four-point bending was simple and convenient, and is therefore applicable to precracking in a variety of brittle materials prior to fracture-toughness measurements.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

In Situ Synthesis and Microstructures of Tungsten Carbide-Nanoparticle-Reinforced Silicon Nitride-Matrix Composites

A W₂C-nanoparticle-reinforced Si₃N₄-matrix composite was fabricated by sintering porous Si₃N₄ that had been infiltrated with a tungsten solution. During the sintering procedure, nanometer-sized W₂C particles grew in situ from the reaction between the tungsten and carbon sources considered to originate mainly from residual binder. The W₂C particles resided in the grain-boundary junctions of the Si₃N₄, had an average diameter of ∼60 nm, and were polyhedral in shape. Because the residual carbon, which normally would obstruct sintering, reacted with the tungsten to form W₂C particles in the composite, the sinterability of the Si₃N₄ was improved, and a W₂C–Si₃N₄ composite with almost full density was obtained. The flexural strength of the W₂C–Si₃N₄ composite was 1212 MPa, ∼34% higher than that of standard sintered Si₃N₄.     

Mechanochemically synthesized ZIF-8 nanoparticles blended into 6FDA-TrMPD membranes for C3H6/C3H8 separation

The mixed matrix membranes (MMMs) consisting zeolitic-imidazolate framework-8 (ZIF-8) nanoparticles in a polymer have been of considerable interest in separation applications. The fillers used are mostly synthesized using the solvothermal method. In this study, the ZIF-8 nanoparticles were synthesized using a solvent-less and salt-free mechanochemical method and were added to 6FDA-TrMPD polyimide to prepare MMMs. The single gas permeation of C₃H₆ and C₃H₈ through the MMMs was investigated. The C₃H₆ permeability and C₃H₆/C₃H₈ ideal selectivity of a 20 wt% mechano-synthesized ZIF-8/6FDA-TrMPD MMM were 70% and 32% higher than those of the neat polymer membrane at 0.1 MPa and 308 K, respectively. The C₃H₆/C₃H₈ separation performance of the mechano-synthesized ZIF-8 MMM was similar to that of the conventional solvothermal-synthesized ZIF-8 MMM. This separation performance was in good agreement with the Maxwell model. Temperature and pressure dependence analyses confirmed that the mechano-synthesized ZIF-8 nanoparticles acted as molecular sieves in the MMMs for the C₃H₆ and C₃H₈ permeation.     

Two-step design of critical control systems using disturbance cancellation integral controllers

An efficient critical control system design is proposed in this paper. The key idea is to decompose the design problem into two simpler design steps by the technique used in the classical loop transfer recovery method (LTR). The disturbance cancellation integral controller is used as a basic controller. Since the standard loop transfer recovery method cannot be applied to the disturbance cancellation controller, the nonstandard version recently found is used for the decomposition. Exogenous inputs with constraints both on the amplitude and rate of change are considered. The majorant approach is taken to obtain the analytical sufficient matching conditions. A numerical design example is presented to illustrate the effectiveness of the proposed design.     

Freestream and vortex preservation properties of high-order WENO and WCNS on curvilinear grids

Freestream and vortex preservation properties of a weighted essentially nonoscillatory scheme (WENO) and a weighted compact nonlinear scheme (WCNS) on curvilinear grids are investigated. While the numerical technique used for the compact difference scheme can be applied to WCNS, applying it to WENO is difficult. This difference is caused by difference in the formulation of numerical fluxes. WENO computed in the generalized coordinate system does not work well for either freestream or vortex preservation, whereas WENO computed in the Cartesian coordinate system works well for both freestream and vortex preservation, but its resolution is lower than that of WCNS. In addition, WENO in the Cartesian coordinate system costs three times as much as WENO or WCNS in the generalized coordinate system. Therefore, WENO in the Cartesian coordinate system is not suitable for solving Euler equations on a curvilinear grid. On the other hand, WCNS computed in the generalized coordinate system works well for freestream and vortex preservation when used with the numerical technique proposed for the compact difference scheme. The results show that WCNS with this numerical technique can be used for an arbitrary grid system. In this paper, the excellent freestream and vortex preservation properties of WCNS when used with the numerical technique, compared with those of WENO, are shown for the first time.