Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Semiconductor photonic functional devices

Recent advances in semiconductor photonic functional devices based on the nonlinearities of laser diodes (LDs) are reviewed. Because the current research is driven primarily by the needs of optical fiber communications systems, most devices are made of InGaAsP and operate at wavelengths of between 1.3 and 1.55 μm, the wavelength window in which optical fibers have their most favorable properties. Minimum loss is at 1.55 μm, and zero dispersion is at 1.3 μm. AlGaAs devices operating at around 0.85 μm have also been reported. Two types of optical bistability-absorptive and dispersive-are explained, and devices based on them are described. Switching characteristics of bistable devices are discussed. Tunable wavelength converters and filters are also examined. Applications to all-optical communication and to optical switching systems are considered. Directions for future development are indicated     

Head-to-head polymers: 33. Bromination of cis-1,4-polybutadiene to head-to-head poly(vinyl bromide)

Cis-1,4-polybutadiene (PB) in a 0.5% solution of a solvent mixture of dichloromethane and 1,2-dibromoethane or tetrahydrofuran was quantitatively brominated with elemental bromine at 0°C under careful exclusion of oxygen to head-to-head poly(vinyl bromide). Partially brominated PB has a structure of random or block sequences of butadiene units in the polymer depending on the bromination solvent but shows no stereospecificity in the CHBrCHBr-dyads. Partially brominated PB with block structure showed a microphase-separated morphology over a wide range of composition. Microphase separation is less pronounced for the more random structure of butadiene units. I.r and ¹³C n.m.r. spectroscopy of the partially brominated PB was used to follow the progress of the bromination.     

A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

The heat transfer and pressure drop characteristics of finned tube banks in forced convection (effects of fin height on pressure drop characteristics)

In recent years the requirement for the reduction of energy consumption has been increasing to solve the problems of global warming and the shortage of petroleum resources. For example, in the power generation field, as thermal power generation occupied 60% of the power generation demand, considerable improvement of the thermal efficiency is required. This paper describes the pressure drop characteristics of finned tube banks used for heat exchangers in thermal power generation that were clarified by testing serrated finned tube banks with different fin heights for improved heat transfer and conventional spiral finned tube banks with different fin heights, and an equation to predict pressure drop which is necessary for the heat exchanger design is proposed. © 2006 Wiley Periodicals, Inc. Heat Trans Asian Res, 35(3): 179–193, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20112