Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

InxGa1−xAs ohmic contacts to n-type GaAs with a tungsten nitride barrier

Significant reduction of the contact resistance of In_0.7Ga_0.3As/Ni/W contacts (which were previously developed by sputtering in our laboratory) was achieved by depositing a W₂N barrier layer between the Ni layer and W layer. The In_0.7Ga_0.3 As/Ni/W₂N/W contact prepared by the radio-frequency sputtering technique showed the lowest contact resistance of 0.2 Ωmm after annealing at 550°C for 10 s. This contact also provided a smooth surface, good reproducibility, and excellent thermal stability at 400°C. The polycrystalline W₂N layer was found to suppress the In diffusion to the contact surface, leading to improvement of the surface morphology and an increase in the total area of the In_xGa−As between metal and the GaAs substrate. These improvements are believed to reduce the contact resistance.     

Graphite formation on Ni film by chemical vapor deposition

Thin film formation of graphite by chemical vapor deposition using 2-methyl-1,2′-naphthyl ketone as a starting material was carried out on Ni film substrates. On Ni films directly deposited on quartz glass, the graphite films were obtained when the Ni film thickness was above 1 000 Å and above 5 000 Å at 700 °C and 1 000 °C, respectively. Depositions on thinner Ni film substrates comprise amorphous carbon (a-C) or graphite tubes which was owing to the thermal coagulation of the Ni film into droplets. On the other hand, graphite film was obtained on the Ni film with thickness 10 Å when a-C was inserted between the Ni film and the quartz glass. The coagulation of the Ni film is considered to be avoided by inserting a-C layer.     

Permeation of Zidovudine and Probenecid from Oily Bases Containing Alcohols Through Rat Skin

Permeation of zidovudine (3'-azido-3'-deoxythymidine, AZT) and probenecid from oily bases containing an alcohol through rat skin was examined. Isopropyl myristate (IPM), as an oily vehicle, showed a penetration enhancing effect for AZT and probenecid. Ethanol, n-propanol, and n-butanol were used as additives in IPM and were examined for their own permeation and the enhancing effect on the permeation of AZT and probenecid. The skin permeation of AZT and probenecid from IPM was enhanced by addition of the alcohol in IPM. The degree of the enhancement was decreased with increasing lipophilicity of the alcohol used. me permeation rate of the drug from those systems was shown to be governed by penetration-enhancing effects of the oily base and alcohol, and the penetration of the alcohol itself through the skin.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Recovery of monomers and fillers from high-temperature-vulcanized silicone rubbers—combined effects of solvent, base and fillers

The depolymerization of high-temperature-vulcanized (HTV) silicone rubbers containing filler silica and alumina into cyclosiloxane monomers and spontaneous recovery of fillers were studied. First, HTV silicone rubber was treated with different types of solvents in the presence of KOH to find that a triad mixture of diethylamine, methanol and hexane was appropriate not only to dissolve the silicone rubber to a suspension but also to separate fillers completely by filtration. The filtrate was distilled to remove solvent first and then give pure cyclosiloxane monomers in 76–84% yields. Second, the rubbers were treated with other types of triad mixture of solvents and bases, e.g. tetramethylammonium hydroxide, hexane and diethylamine. After filtration, residue was again treated with the amine and hexane to recover clean fillers in 83–93% yields. Cyclosiloxane monomers were also obtained from the combined filtrates in 67–78% yields.     

A study of suppression of vapor explosions by adding inversely soluble polymers

The mechanism of the suppression of vapor explosions by adding inversely soluble polymers in water is studied. Vapor explosion experiments and quench experiment are conducted using a silver test piece. Polymetric solution (polyethylene oxide), of concentrations from 0 to 500 wppm, whose normalized viscosity (by water) varies from 1.00 to 2.00, is used. No vapor explosion is observed in the aqueous polymer solution at a concentration higher than 200 wppm. Quench experiments using the silver test piece submerged in the polymer solution and water are performed in order to examine the stability of film boiling. The suppression of the vapor film collapse is attributed to the precipitation of polyethylene as a gel around the vapor film. © 2002 Wiley Periodicals, Inc. Heat Trans Asian Res, 31(4): 297–306, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.10037     

Virtualized Reality: Perspectives on 4D Digitization of Dynamic Events

Digitally recording dynamic events, such as sporting events, for experiencing in a spatio-temporally distant and arbitrary setting requires 4D capture: three dimensions for their geometry and appearance over the fourth dimension of time. Today's computer vision techniques make 4D capture possible. The virtualized reality system serves as an example on the general problem of digitizing dynamic events. In this article, we present the virtualized reality system's details from a historical perspective