NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.     

Thickness dependence of H2 gas sensor in amorphous SnQx films prepared by ion-beam sputtering

Amorphous SnO_x films were deposited by ion-beam sputtering on sintered alumina substrates. Amorphous film sensors were prepared by annealing the films at 300° C for 2 h in air. The thickness dependence of resistivity and hydrogen gas sensitivity were measured at 150° C over the thickness range 1 to 700 nm. A resistivity maximum was observed in ultrathin films. Resistivity increased by three orders of magnitude with increasing film thickness from 0.9 to 7.4 nm and then decreased by five orders of magnitude from 7.4 to 35 nm. Ultrathin film sensors showed sensitivity maxima around a thickness of 10 nm. Sensitivity and resistivity of ultrathin films were significantly influenced by the thermal expansion coefficient and the surface state of the substrate.     

Properties of indium oxide/tin oxide multilayered films prepared by ion-beam sputtering

The preparation and characterization of indium oxide (InO _x )/tin oxide (SnO _y ) multilayered films deposited by ion-beam sputtering are described and compared with indium tin oxide (ITO) films. The structure and the optoelectrical properties of the films are studied in relation to the layered structures and the post-deposition annealing. Low-angle X-ray diffraction analysis showed that most films retained the regular layered structures even after annealing at 500° C for 16 h. As an example, we obtained a resistivity of 6×10^–4 cm and a transparency of about 85% in the visible range at a thickness of 110 nm in a multilayered film of InO _x (2.0 nm)/SnO _y (0.2 nm)×50 pairs when annealed at 300° C for 0.5 h in air. Hall coefficient measurements showed that this film had a mobility of 17 cm² V^–1 sec^–1 and a carrier concentration (electron density) of 5×10²⁰ cm^–3.     

Revolving Vernier Mechanism Controls Size of Linear Homomultimer

A new kind of the Vernier mechanism that is able to control the size of linear assembly of DNA origami nanostructures is proposed. The mechanism is realized by mechanical design of DNA origami, which consists of a hollow cylinder and a rotatable shaft in it connected through the same scaffold. This nanostructure stacks with each other by the shape complementarity at its top and bottom surfaces of the cylinder, while the number of stacking is limited by twisting angle of the shaft. Experiments have shown that the size distribution of multimeric assembly of the origami depends on the twisting angle of the shaft; the average lengths of the multimer are decamer, hexamer, and tetramer for 0°, 10°, and 20° twist, respectively. In summary, it is possible to affect the number of polymerization by adjusting the precise shape and movability of a molecular structure.     

Bacteriological, pharmacokinetic and clinical evaluation of azithromycin in the pediatric field]

Azithromycin (AZM), a new macrolide antibiotic, in fine granules and in capsules was studied for pharmacokinetic and clinical evaluation in the pediatric patients. Antibacterial activity of AZM against 43 clinical isolates: AZM exhibited slightly lower activity against Gram-positive bacteria and 2-8-fold higher activity against Gram-negative bacteria than erythromycin or clarithromycin. Plasma or urine samples were collected from eight patients receiving the drug in fine granular form, and two patients receiving it in capsules for the determination of drug levels. The elimination half-lives of AZM after administration at dose of 10 mg/kg/day for 3 days were 50.0 and 51.2 hours for fine granules, and 41.5 hours for capsules. AUC0-infinity was 11.7 and 24.3 micrograms.hr/ml for fine granules, and 8.3 micrograms.hr/ml for capsules. The cumulative excretion rates up to 120 hours after the start of treatment were 8.24 and 13.84% for fine granules, and 3.83% for capsules. AZM was administered to 123 patients once daily at 3.7-20.0 mg/kg body weight over 3 to 5 days with reference to the standard dose of 10 mg/kg. The drug was used to treat patients with pharyngitis, tonsillitis, scarlet fever, pneumonia, mycoplasmal pneumonia, chlamydial pneumonia, otitis media, pertussis, intestinal infection, and SSTI. The effectiveness of AZM was evaluated in 109 cases. The drug was rated "excellent" in 65.1% of the patients and "good" in 29.4%, resulting in an efficacy rate of 94.5%. Furthermore, AZM eradicated 43 of 46 (93.5%) bacteria that had been identified before the treatment. Three patients complained of side effects of urticaria (1 case) and diarrhea (2 cases). Abnormal laboratory changes were reported as follows: decreased leukocyte (3 cases), increased eosinophil (5), increased platelet (2), increased eosinophil and platelet, elevated GPT (1), and elevated GOT and GPT (1). The abnormalities, however, were mild enough to raise no clinically significant problems. In conclusion, AZM in once daily regimen was effective and safe in treatment of pediatric infections.     

Electrochemical analysis of zincate treatments for Al and Al alloy films

Electrochemical behavior of Al and Al alloy films in zincate solution was investigated to elucidate the effect of the zincate pretreatment for electroless NiP deposition, which is used for under bump metallization for LSI interconnects. The immersion potential for AlCu and AlSiCu, immediately reached to constant, which was almost equal potential to zinc reference electrode. The corrosion current for the AlCu and AlSiCu films was larger than that of the Al and AlSi films in the zincate solution. It was also confirmed that the deposited Zn at the surface of AlCu and AlSiCu films possessed smaller grain size and larger amount of nucleation, resulted in the formation of flat NiP films.     

Effect of the addition of silver compounds during the pyrolysis of manganese nitrate on tantalum anodic oxide film

A study of the pyrolysis of an aqueous solution of manganese nitrate in the presence of silver compounds has been carried out. Thermal analysis showed that the MnO₂ formation temperature and the transformation temperature from MnO₂ to Mn₂O₃ shifted towards a lower temperature in the presence of silver acetate. A large particle-size and high crystallinity MnO₂ was formed; this may be a useful method of making an excellent tantalum capacitor with high capacitance.