Polarity Effect and Electromagnetic Radiation of Partial Discharge Accompanying Growth of Electrical Tree

We have investigated the characteristics of radiated electromagnetic (EM) waves from positive and negative partial discharges (PD) in epoxy resin and cross‐linked polyethylene. We found that there is a correlation among the EM level from PD, the positive PD current, and electrical trees. Therefore, the growth of an electrical tree produces a lot of positive PD. We have also investigated the characteristics of the frequency region of EM waves from PD in air, insulating oil, and liquid epoxy in addition to the above insulators. EM waves were detected in the frequency region of 40 MHz to 300 MHz from positive and negative PD in epoxy resin and cross‐linked polyethylene. EM waves were also detected in the frequency region of 40 MHz to 150 MHz from positive and negative PD in air. In the case of insulating oil and liquid epoxy, EM waves were detected in the frequency regions of 40 MHz to 150 MHz from positive PD, and 40 MHz to 250 MHz from negative PD. The frequency region differed depending on the material and the discharge polarity. Our investigation indicates that the cause is differences in electric field strength at the time of PD occurrence.     

Pinpoint injection of microtools for minimally invasive micromanipulation of microbe by laser trap

This paper reports transportation of the target microbe by the laser trapped microtools with minimum laser irradiation to the target. The size of a microtool (MT) is around micrometer. The MTs are manipulated by the focused laser under the microscope to manipulate the target microbe. Here we propose a pinpoint injection method of MTs at the desired location in the microchamber, which is filled with liquid. At first, we classified the injection method of the MTs in four categories. Here we employed a new method to install the MTs inside the microchamber. We developed a MT holding chip to install the MTs. The MTs were injected in the microchamber, and were manipulated successfully by the laser scanning micromanipulator to transport the target microbe for separation. The proposed method is useful for the pinpoint injection of MTs and separation by the indirect micromanipulation.     

Reduction of noise figure in semiconductor laser amplifiers with Ga1-xInxAs/GaInAsP/InP strained quantum wellstructures

The noise characteristics of semiconductor laser amplifiers (SLAs) in the Ga_1-xIn_xAs/GaInAsP/InP strained quantum well (QW) system are theoretically calculated and analyzed using density-matrix theory and taking into account the effects of band mixing on both the valence subbands and the transition dipole moments. The numerical results show that a reduced noise figure can be obtained in both tensile and compressively strained QW structures due to the increase in differential gain and the decrease in transparent carrier density. From a comparison among compressively strained (x=0.70), unstrained (x=0.53), and tensile strained (x=0.40) QW SLAs at a fixed carrier density and optical confinement factor, it is found that the noise figure of the tensile strained QW reaches its lowest value of 3.4 dB at average input optical power of -20 dB     

Recovery of fluorocarbons in Japan as a measure for abating global warming

The objective of this study is to evaluate the potential for recovering fluorocarbons as measures for the abatement of global warming. In this study, we focused on the three different kinds of fluorocarbons: CFCs, HCFCs and HFCs, and targeted refrigerant use because of the availability of relevant data. We first estimated future fluorocarbon emissions from the targeted appliances; we next compared those emissions in the units of CO₂ equivalent to the level of CO₂ emissions in 1990 from a quantitative point of view. As the result of this study, it was found that fluorocarbon emissions in 1999 and 2010 would be equal to approximately 7 and 3% of the level of CO₂ emissions in 1990 respectively. Moreover, if we implement a 100% recovery rate in every recovery route, we can reduce a large amount of emissions which correspond to approximately 2–5% of the level of CO₂ emissions in 1990, even if we take into account the energy-related CO₂ emissions by the transportation and decomposition of fluorocarbons.     

An Analysis of Scheduling Policies In Multiechelon Production Systems

Results of a simulation study of the economics of frequency of rescheduling Material Requirements Planning (MRP) systems are presented for a single-product, two-stage system in which demand is uncertain. The results indicate that for systems with moderate demand uncertainty, frequent rescheduling to maintain customer service may be uneconomical when compared with the alternative of more stable schedules in conjunction with safety stock. This result arises primarily because the cost of “emergency” production setups which occur when rescheduling is frequent exceeds the cost of safety stock required to “protect” stable schedules.     

Temporal Specificity of Extinction in Autoshaping.

Three experiments investigated the effects of varying the conditioned stimulus (CS) duration between training and extinction. Ring doves (Streptopelia risoria) were autoshaped on a fixed CS-unconditioned stimulus (US) interval and extinguished with CS presentations that were longer, shorter, or the same as the training duration. During a subsequent test session, the training CS duration was reintroduced. Results suggest that the cessation of responding during an extinction session is controlled by generalization of excitation between the training and extinction CSs and by the number of nonreinforced CS presentations. Transfer of extinction to the training CS is controlled by the similarity between the extinction and training CSs. Extinction learning is temporally specific. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

The small GTP-binding protein Rho1 is a multifunctional protein that regulates actin localization, cell polarity, and septum formation in the fission yeast Schizosaccharomyces pombe

BACKGROUND: The small GTP-binding protein Rho has been shown to regulate the formation of the actin cytoskeleton in animal cells. We have previously isolated two rho genes, rho1+ and rho2+, from the fission yeast Schizosaccharomyces pombe in order to investigate the function of Rho using genetic techniques. In this paper, we report the cellular function of Rho1. RESULTS: We found that Rho1 is essential for cell viability and cell polarity using gene disruption and by exogenous expression of botulinum C3 ADP-ribosyltransferase. In cells expressing either a constitutively active Rho1 or a dominant-negative Rho1, actin patches were delocalized. Both the cell wall and secondary septum were thick and stratified in cells expressing the constitutively active Rho1, while the cell wall of cells expressing the dominant-negative Rho1 seemed to be loosely organized. Furthermore, inactivation of Rho1 is apparently required for the separation of daughter cells. Cell fractionation studies suggested that Rho1 is predominantly membrane-bound. Moreover, we observed that Rho1 is localized to the cell periphery and to the septum. CONCLUSIONS: Rho1 is involved in actin patch localization, the control of cell polarity, the regulation of septation, and cell wall synthesis.     

HEURISTIC APPROACHES FOR LOADING PROBLEMS IN FLEXIBLE MANUFACTURING SYSTEMS

Flexible manufacturing systems (FMSs) are able to process a wide variety of operations, but the specific mix of operations that can be performed at any point in time depends upon the combination of tools loaded onto the machines. The machines have tool magazines with finite capacities. We consider the problem of assigning operations and their associated tools to machines (or groups of machines) to maximize the throughput for a specified steady-state mix of orders. Since this objective is difficult to deal with directly, we use an intermediate objective of meeting workload targets for each machine group as closely as possible. A certain form of this intermediate objective has been shown to correlate highly with the original objective.

Since it is computationally intractable to find optimal solutions for problems with more than 20 operations, fast heuristic algorithms are developed. These algorithms are adapted from multi-dimensional bin-packing algorithms. Computational results are reported.