Soft X-ray image storage in poly (methylmethacrylate)

Images stored in resist for soft X-ray lithography or microradiography were found to show a background noise which limits the resolution. This is due to the statistically variable spatial distribution of the photons incident on the resist surface. An estimate of the fundamental noise-limited resolution has been made from the experimental measurement of photon flux incident on the surface and the accurate development rate curves. Monochromatic radiation from a synchrotron source was used.     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Ortho-deuterium Raman laser using the S0(2) rotationaltransition in the mid-infrared region

Based on a calculation for the Raman gain coefficient of the S₀(2) transition in ortho-D₂, we have demonstrated the generation of first Stokes waves in the 15-16-μm spectral region. Use of ortho-D enriched by a catalytic converter enabled us to realize efficient conversion at room temperature. Stokes energies as high as 400 mJ were obtained     

A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

填充热丝激光窄间隙焊接的实验研究

将填充热丝应用到高光束质量、长焦距的光纤激光窄间隙焊接中,不锈钢母材通过激光加热,镍基焊丝通过电流加热,有效利用复合热源的优势,提高了焊丝过渡稳定性和熔覆效率。通过高速摄像机对送丝过程进行在线观察,分析工艺参数对焊丝过渡的影响。研究不锈钢和镍基合金异种金属窄间隙焊接接头的凝固组织,并对焊缝金属进行元素分布扫描。研究发现,由焊丝电流和送丝速度等工艺参数决定的送丝稳定性是影响填充热丝激光焊接质量的最主要因素。对于窄间隙焊接,采用与间隙宽度相当的离焦光斑激光热导焊,可形成较好的侧壁熔合,由熔融金属曲面和侧壁构成的激光反射是侧壁熔合的主要原因。焊缝冷却速度较快,焊缝金属的凝固组织呈明显的对生生长,在坡口侧壁附近其生长方向与侧壁近似垂直,焊缝不存在宏观偏析。在间隙底部直角处容易出现未熔合现象,采用底部圆弧过渡的U型坡口后,可较好地解决底部未熔合问题,获得了无宏观缺陷的焊接接头。     

90-nm process-variation adaptive embedded SRAM modules with power-line-floating write technique

The power consumption of a low-power system-on-a-chip (SoC) has a large impact on the battery life of mobile appliances. General SoCs have large on-chip SRAMs, which consume a large proportion of the whole LSI power. To achieve a low-power SoC, we have developed embedded SRAM modules, which use some low-power SRAM techniques. One technique involves expanding the write margin; another is a power-line-floating write technique, which enables low-voltage write operation. The power-line-floating write technique makes it possible to lower the minimum operating supply voltage by 100 mV. The other techniques involve using a process-variation-adaptive write replica circuit and reducing leakage current. These techniques reduce active power during write operations by 18% and reduce active leakage of the word-line driver by 64%. The prototype SRAM modules achieve 0.8-V operation, and a 512-kb SRAM module achieves 48.4-/spl mu/A active leakage and 7.8-/spl mu/A standby leakage with worst-leakage devices.     

A general cone-beam reconstruction algorithm

Considering the characteristics of the X-ray microscope system being developed at SUNY at Buffalo and the limitations of available cone-beam reconstruction algorithms, a general cone-beam reconstruction algorithm and several special versions of it are proposed and validated by simulation. The cone-beam algorithm allows various scanning loci, handles reconstruction of rod-shaped specimens which are common in practice, and facilitates near real-time reconstruction by providing the same computational efficiency and parallelism as L.A. Feldkamp et al.'s (1984) algorithm. Although the present cone-beam algorithm is not exact, it consistently gives satisfactory reconstructed images. Furthermore, it has several nice properties if the scanning locus meets some conditions. First, reconstruction within a midplane is exact using a planar scanning locus. Second, the vertical integral of a reconstructed image is equal to that of the actual image. Third, reconstruction is exact if an actual image is independent of rotation axis coordinate z. Also, the general algorithm can uniformize and reduce z-axis artifacts, if a helix-like scanning locus is used.     

A molten metal jet impingement on a flat spreading surface

ABSTRACT

In the event of a severe accident, past experiences such as Three Mile Island and Fukushima Daichi have shown that the reactor core of a light-water nuclear reactor, if not properly safeguarded, could go through a meltdown. This will be followed by the formation of a corium, a mix of molten fuel elements, and liquid metals from the Reactor Pressure Vessel (RPV). In the worst-case scenario, a melt through from the RPV can occur and lead to the spreading of the corium, in the form of a molten element’s jet impinging on a flat concrete structure of the Primary Containment Vessel (PCV). To enhance the decommissioning and the safety procedure, scope of the present article is to deepen the understanding of the phenomena involved in the mentioned scenario, mainly jet-instability and molten material spreading. In the present study, experiments were carried out, by using corium simulant materials such as Copper and Tin, to investigate the link between the instability of the gravity-driven molten metal jet and the impinging followed by its spreading over a flat area.     

Interfacial tension of demixed polymer solutions near the critical temperature: polystyrene + methylcyclohexane

Interfacial tension between demixed solutions of polystyrene + methylcyclohexane has been measured near the critical temperature as a function of temperature using polystyrenes with molecular weights 9000 ～ 1.26 × 10⁶. The critical exponent for the interfacial tension was determined to be about 1.30 for the lower molecular weight systems. However, for higher molecular weights the exponent could not be obtained because the system departed from critical behaviour. Magnitudes of the interfacial tension were proportional to about N^?0.44, where N is the polymerization index. Experimental results were compared with the recently-proposed theories and found to be in qualitative agreement. The tricritical theory of polymer solutions was also compared with the experimental results.     

Spray Pyrolysis of Fe3O4–BaTiO3 Composite Particles

Fe₃O₄–BaTiO₃ composite particles were successfully prepared by ultrasonic spray pyrolysis. A mixture of iron(III) nitrate, barium acetate and titanium tetrachloride aqueous solution were atomized into the mist, and the mist was dried and pyrolyzed in N₂ (90%) and H₂ (10%) atmosphere. Fe₃O₄–BaTiO₃ composite particle was obtained between 900° and 950°C while the coexistence of FeO was detected at 1000°C. Transmission electron microscope observation revealed that the composite particle is consisted of nanocrystalline having primary particle size of 35 nm. Lattice parameter of the Fe₃O₄–BaTiO₃ nanocomposite particle was 0.8404 nm that is larger than that of pure Fe₃O₄. Coercivity of the nanocomposite particle (390 Oe) was much larger than that of pure Fe₃O₄ (140 Oe). These results suggest that slight diffusion of Ba into Fe₃O₄ occurred.