Neural mechanism of pupillary dilation elicited by electro-acupuncture stimulation in anesthetized rats

The neural mechanisms to reflex dilation elicited by electro-acupuncture stimulation were investigated in anesthetized rats. Two needles, with 160 microns diameter and about 5 mm apart, were inserted into the skin and underlying muscle of a hindpaw. Repetitive 20 Hz, 0.5 ms electrical pulses at various intensities were used for stimulation for 30s. The pupil size was magnified about 44 times via a microscope and was continuously recorded on a videotape. Electro-acupuncture stimulation at more than 0.5 up to 6 mA induced stimulus intensity-dependent pupil dilation. These responses were abolished by the severance of the sciatic and saphenous nerve of the stimulated hindlimb. Compound action potentials were recorded from the distal cut end of the tibial of a saphenous nerve following electro-acupuncture stimulation of the hindpaw. The mean threshold of the compound action potentials of the myelinated fibers in saphenous nerves was 0.18 mA, while that of unmyelinated fibers was 3.0 mA. The mean threshold of the compound action potentials of the myelinated fibers in the tibial nerve was 0.20 mA of unmyelinated fibers was 3.3 mA. Severance of bilateral trunks did not affect the response, while severance of the third cranial nerves abolished the responses. In conclusion, electro-acupuncture stimulation applied to the hindpaws of the anesthetized rats induced excitation of myelinated or of both myelinated and unmyelinated afferent fibers of the tibial and saphenous nerve, and involved a reflex response of pupil dilation through the third cranial parasympathetic efferent nerve.     

Markedly compressible behaviors of gellan hydrogels in a constrained geometry at ultraslow strain rates

The fracture behaviors of gellan hydrogels under compression remarkably depend on the strain rate as well as the boundary conditions for lateral expansion. In the geometry with no constraint for lateral expansion (conventional uniaxial compression), the gels rupture at relatively small strains independently of the compression rates. In contrast, when the gels are compressed extremely slowly (at a strain rate of ca. 10⁻⁵ s⁻¹) in the geometry prohibiting the lateral expansion at their top and bottom surfaces, they are remarkably compressible down to 2% of the initial height without macroscopic fracture and they are accompanied by a large amount of water release. In such markedly compressed gels, many microscopic cracks are formed around the central layer, where strain concentration occurs due to the nonuniform deformation arising from the constrained geometry. In the highly compressible case, the formation of macroscopic cracks is prevented by the localization of microscopic cracks as well as the enhancement in mechanical toughness by a significant increase in polymer concentration due to water release.     

Geochemical characteristics of the Yufuin outflow plume, Beppu hydrothermal system, Japan

Thermal water at Yufuin (Kyushu Island, Japan) is tapped through about 820 shallow wells and used mainly for hot-spring bathing purposes. Chemical and isotopic data for fluids from wells and fumaroles in Yufuin and Beppu indicate that the thermal activity at Yufuin represents a dilute, westward-flowing hydrothermal outflow plume from the Beppu hydrothermal system. Two other (eastward-flowing) outflow plumes have long been recognized at Beppu, but the Yufuin outflow plume is first recognized here. The Yufuin outflow plume is apparently a mixture of two end-member fluids: (1) deep high-temperature (250–300°C) fluid from the Beppu system having high chloride concentration (1400–1600 mg/L) and a δ¹⁸O value near −6.0%, and (2) meteoric water having low chloride concentration (≤7 mg/L) and a δ¹⁸O value near −9.2%.A permeable conduit for the vertical and lateral transport of deep fluid from the Beppu system is provided by the Yufuin Fault zone, which extends westward from the southern flank of Mt. Tsurumi volcano to the town of Yufuin. Stable isotope ratios and chloride concentrations for shallow groundwaters near the eastern end of the fault, at an elevation near 700 m, are consistent with those required for the low-chloride meteoric end-member of the Yufuin thermal waters. Recharge of this meteoric water, as well as mixing with the Beppu deep fluid, may occur along the Yufuin Fault. Enthalpy-chloride relations indicate additional conductive heating of the Yufuin waters, in the amount of 350–500 kJ/kg beyond that which can be accounted for by mixing between Beppu deep fluid and meteoric water. This could be a result of conductive heating with convection to a depth of 1–2 km. Estimates of the magnitude of the heat source for the Beppu hydrothermal system should take into account the heat being discharged at Yufuin.     

A feasibility study of a direct-mapping parallel processing method to solve linear equations in load-flow calculation

With the growing size and complexity of power systems, system analysis—such as transients calculation—takes much time. Hence, fast calculation methods are required. Although parallel processing is a hopeful method, there have been difficulties in the parallel solution of linear equations which appear in power-flow calculations by the Newton-Raphson method. This paper aims at the fast calculation of the power-flow problem by means of parallel processing. In order to improve the suitability to the parallel solution of the differential equation in transients calculation, we assume the use of a direct-mapping parallel processing machine to map directly the network of a power system onto a network of processors. Under this assumption, we propose a new parallel-processing-oriented method in which the linear equation is solved by linear iterations between nodes with Aitken acceleration. We simulate the method on three model power systems and compare this Parallel Iterative Method (PIN) with a Parallel Direct Method (PDM) which uses the banded matrix according to the number of operations required. As a result, we can expect that PIM may solve linear equations faster than PDM with m processors, although the PIM might be inferior to the PDM with m × m processors, where m denotes the half-band width of the banded matrix.     

Carcinosarcoma of the rectosigmoid colon: report of a case

We report an unusual case of carcinosarcoma of the colon. An 80-year-old woman was admitted to our hospital with lower abdominal pain. Computed tomography showed a large pelvic mass, 18cm in maximal diameter, and barium enema and colonoscopy both showed a type-2 tumor in the sigmoid colon. We performed Hartmann's procedure with resection of the ileocolic segment. Immunohistochemical stains of the resected specimen revealed that most of the tumor consisted of spindle cell sarcoma with neural and muscle differentiation, while only the superficial area of an ulcerated lesion contained adenocarcinoma positive for carcinoembryonic antigen. The patient died of a fast-growing recurrent pelvic tumor 6 months postoperatively. Our experience of this case and our review of eight other cases in the English literature indicate that wide resection provides the best chance of cure, but careful postoperative follow-up is essential.     

Slit flow of molten polyethylene filled with plastic flakes

The processability of polyethylene in sheet-extrusion or calendering may be improved by the addition of plastic flakes. The effects of plastic flake parameters and flow conditions on the viscosity and the die swell of the suspension were determined, and the structure in flow (morphology or dispersion state) and applications were discussed. Flakes of biaxially oriented polystyrene, high-impact polystyrene, polypropylene, polyamide or polypropylene spheres were dry-blended with polyethylene. The viscosity was determined by means of a slit or a capillary rheometer. The quenched extrudate was annealed and its die swell was measured. Flakes of biaxially oriented polystyrene shrunk into rod-like form during heating, but other plastics retained the flake-form. The relative viscosity and the swell ratio of the suspensions depended on the type of plastic and operating conditions. The rheological behavior of suspensions qualitatively suggested that polypropylene flakes deformed or crowded (including stacking), polyamide flakes deformed slightly, and polystyrene flakes were difficult to buckle, but crowded slightly. The thickness of extrudates can be controlled easily by flake addition due to decreased die swell, while the output would be reduced to some extent.     

Properties of networks obtained by internal plasticization of epoxy resin with aromatic and aliphatic glycidyl compounds

In order to improve the fracture properties of p, p′-diaminodiphenylmethane-cured epoxy resin, various kinds of aromatic and aliphatic glycidyl compounds were investigated as a modifier at an amount of 30 wt %. Several compounds promoted the fracture toughness. In any glycidyl compounds, however, heat resistance was decreased by the modification. The dynamic mechanical properties of the modified epoxy resins were measured. The crosslinking density ρ was calculated from the theory of rubber elasticity, and the mechanical properties of the resins were discussed in regard to the crosslinking density. Tensile strength was scarcely affected by the crosslinking density. Elongation at break and Izod impact strength increased remarkably with decrease in crosslinking density. The fracture toughness K_Ic- increased with decrease in crosslinking density except at small ρ.     

Rinsing effect of alkaline electrolyzed water on nickel surfaces

The improvement in the surface cleanliness of electroplated nickel by rinsing in alkaline electrolyzed water (AEW) was determined. When the nickel plated sample was rinsed with the AEW, it was found that the amount of residual sulfate ion on the surface of a sample decreased approximately by half compared to one rinsed only with de-ionized pure water. Because nanosize hydrogen bubbles are present in the AEW, and the zeta-potential has a negative value, we then surmised that the mechanism of rinsing was as follows: The sulfate ions are selectively absorbed on the nanosize colloidal hydrogen bubbles, or substituted for anions absorbed on the hydrogen bubbles. The sulfate ions absorbed on the nickel surface then become detached. The detached sulfate ions are absorbed on the surface of the hydrogen bubbles, and negatively charge the hydrogen bubbles. It can be considered that any detached sulfate ions do not re-adhere due to the electrical repulsion force of the negatively charged nickel surface. Thus the sample is efficiently rinsed.