Two-step sinter-crystallization of K2O–CaO–P2O5–SiO2 (45S5-K) bioactive glass

Bioactive glasses and glass-ceramics (GCs) effectively regenerate bone tissue, however most GCs show improved mechanical properties. In this work, we developed and tested a rarely studied bioactive glass composition (24.4K₂O-26.9CaO-46.1SiO₂-2.6P₂O₅ mol%, identified as 45S5-K) with different particle sizes and heating rates to obtain a sintered GC that combines good fracture strength, low elastic modulus, and bioactivity. We analyzed the influence of the sintering processing conditions in the elastic modulus, Vickers microhardness, density, and crystal phase formation in the GC. The best GC shows improved properties compared with its parent glass. This glass achieves a good densification degree with a two-step viscous flow sintering approach and the resulting GC shows as high bioactivity as that of the standard 45S5 Bioglass®. Furthermore, the GC elastic modulus (56 GPa) is relatively low, minimizing stress shielding. Therefore, we unveiled the glass sintering behavior with concurrent crystallization of this complex bioactive glass composition and developed a potential GC for bone regeneration.     

High‐intensity sweeteners in espresso coffee: ideal and equivalent sweetness and time–intensity analysis

The efficient substitution of sucrose by a sweetener in beverages requires the application of some sensory techniques. First, one must determine the concentrations of the sweeteners under study, equivalent in sweetness to the ideal sucrose concentration. In addition, it is fundamental to determine which is most similar to sucrose. The objectives of this study were to determine the ideal sweetness for espresso coffee and the equivalent concentrations in sweetness of different sweeteners, as well as characterise the time–intensity profile of each sweetener in relation to sweetness. The sweeteners evaluated were sucralose, aspartame, neotame, a cyclamate/saccharin mixture (2:1) and stevia. The sucrose concentration considered ideal by consumers was 12.5% (w/v), and the equivalent concentrations of the sweeteners were 0.0159% for sucralose, 0.0549% for aspartame, 0.0016% for neotame, 0.0359% for the cyclamate/saccharin mixture and 0.0998% for stevia. The time–intensity analysis indicated that possibly the sweeteners neotame, aspartame and sucralose would be the best substitutes for sucrose.     

Carcinoembryonic antigen in diagnosis and monitoring of colorectal cancer]

Female SJL mice are more susceptible than male mice to experimental autoimmune encephalomyelitis (EAE) induced by myelin basic protein (MBP)-specific T lymphocytes. In the present study, we examined mechanisms involved in this gender-related difference in disease susceptibility. MBP-specific T lymphocytes derived from spleens of males during the effector phase of adoptive EAE produced significantly higher levels of IL-10, an anti-inflammatory cytokine in EAE. A protective effect of testosterone was then shown. Females implanted with dihydrotestosterone pellets demonstrated a significantly less severe course of EAE as compared with females implanted with placebo pellets. Finally, MBP-specific T lymphocytes derived from dihydrotestosterone-implanted females produced significantly higher levels of IL-10 than those from placebo. Together these data indicate that testosterone exerts a protective effect in EAE that is mediated at least in part by enhanced production of IL-10 by autoantigen-specific T lymphocytes.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

The impacts of a GTL plant on Brazil's oil products supply and refinery expansion

This paper assesses the impacts of a GTL plant on the expansion of Brazil's oil refining segment. The GTL plant (50,000 bpd) was sized to start up operations in 2015, producing diesel and naphtha through the indirect route (FT-synthesis). This plant will consume the non-associated natural gas production from the recent discoveries at the Santos Basin (around 419 Bm³), and the associated gas production from the Campos Basin. Both basins are located in the Southeast of Brazil, the most populated, rich and industrialized region of the country. Two different criteria for refinery expansion were simulated in order to meet oil product demand scenarios. Findings show that depending on the refinery expansion criteria considered GTL will play a fundamental hole to meet the oil product demand forecast to Brazil in the next 10 years.     

Silicon-to-steel bonding using rapid thermal annealing

This paper presents the rapid, low-temperature bonding between silicon and steel using the rapid thermal annealing process. Three different thin-film adhesion layer systems including silver, gold, and nickel were utilized as the intermediate bonding material to assist the eutectic Pb/Sn bonding between silicon and steel. The bonding temperature was set at 220/spl deg/C for 20 s, with a 20-s ramp-up time. Five experiments were conducted to determine the strength of the bond, including static tensile and compressive four-point bend tests, axial extension tests, tensile bending fatigue tests, and corrosion resistance tests. The test results have shown that the gold adhesion layer is the most robust, demonstrating minimal creep during fatigue tests, no delamination during the tensile or compressive four-point bend tests, and acceptable strength during the axial extension tests. Additionally, all adhesion layers have withstood four months of submersion in various high-temperature solutions and lubricants without failure. Simulations of the axial stresses and strains that developed during the four-point bend and axial extension tests were performed and showed that the presence of the silicon die provides a local reinforcement of the bond as observed in the experimental tests.     

Dynamic vulcanisation of EPDM/PE-based thermoplastic vulcanisates studied along the extruder axis

Simple blending and dynamic vulcanisation of EPDM/PE blends using the resol/SnCl₂ system was studied in an extruder using a series of sampling devices. The melting of the PE pellets occurs just in front of and in the first kneading zone. Upon complete melting of the PE phase, the EPDM/PE blends reach very quickly their final morphology. Crosslinking of the EPDM phase to high levels occurs already when the PE phase is not yet fully molten. The higher the EPDM content, the higher the viscous dissipation, the higher the melt temperature and, consequently, the higher the crosslinking rate. For the EPDM/PE (50/50; w/w) TPV a transition from continuous via co-continuous to fully dispersed EPDM is observed, which is driven by crosslinking. Although the degree of crosslinking of the EPDM rubber is very high, this does not prevent phase inversion of the blend. The EPDM/PE interface is rather blurred, because PE crystalline lamellae are growing into the EPDM domains, probably because of the high compatibility between PE and EPDM (60 wt% of ethene). This study shows that dynamic vulcanisation in extruders proceeds quite differently from that in batch kneaders, where melting, mixing and crosslinking are separated in time. In extruders mass and heat transport, melting of the thermoplastic, morphology development (including dispersion and phase inversion), distribution and dissolution of (crosslinking) chemicals and crosslinking of the rubber do not occur as independent phenomena, but mutually and/or continuously interact.