Swelling properties of chemically modified oil palm empty fruit bunch based polyurethane composites

In this study, the diffusion of various types of solvent in oil palm empty fruit bunch/polyurethane composites, produced from chemically modified empty fruit bunches, was investigated. The solubility parameters and polymer–solvent interaction parameters of the produced composites were determined. The void contents of the composites were also determined before swelling tests to eliminate the free solvent present in the system. From the results obtained, we found that the diffusion of the solvents was dependent on the compatible group available and the voids present in the system. The solubility parameters of the empty fruit bunch/polyurethane composites with different degrees of chemical modification were 11.6 and 11.7 (cal/cm^?3)^1/2. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Reliability of railway traffic personnel

The paper describes an analysis of reliability of railway traffic personnel. The human tasks critical to system safety are identified. Human error probability is chosen as a measure of human reliability in performing these tasks. The probabilities of some critical errors are estimated using the field data collected in the Slovenian railway traffic system. As stress conditions strongly affect the human performance, a simple model of the dependence of human error probability on stress levels is proposed.     

Polyurethane composites based on oil palm empty fruit bunches: Effect of isocyanate/hydroxyl ratio and chemical modification of empty fruit bunches with toluene diisocyanate and hexamethylene diisocyanate on mechanical properties

This study focuses on the effect of isocyanate (NCO)/hydroxyl (OH) group ratios and chemical modification of oil palm empty fruit bunches (EFBs) with toluene diisocyanate (TDI) and hexamethylene diisocyanate (HMDI) on the mechanical properties of EFB–polyurethane (PU) composites. The tensile, flexural, and impact properties are affected by the NCO/OH ratios. The tensile strengths, flexural strengths, and toughness increase as the NCO/OH increases; however, the modulus decreases. The reduction in the modulus is attributable to the increased flexibility of the PU linkages. Chemical modification of the EFBs increases the tensile strength, flexural strength, and toughness; however, the modulus is lowered as the percentage of treated EFB is increased. Impact strength results show that the strength increases as the NCO/OH ratio is increased. At NCO/OH ratios of 1.0 and 1.1, the composites with HMDI‐treated fibers exhibit higher impact strength than those with TDI‐treated and untreated fibers, respectively. This may be due to the longer and more flexible chain length of HMDI as compared to TDI, which enables the composites to absorb more energy before failure. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Modification of oil palm empty fruit bunches with maleic anhydride: The effect on the tensile and dimensional stability properties of empty fruit bunch/polypropylene composites

Oil palm empty fruit bunch (EFB)‐filled polypropylene (PP) composites were produced. The EFB filler was chemically modified with maleic anhydride (MAH). The effects of the filler size and chemical modification of EFBs on the tensile and dimensional stability properties of EFB–PP composites were studied. The composites with MAH‐treated EFBs showed higher tensile strengths than those with untreated EFBs. This was attributed to the enhanced compatibility between the MAH‐treated EFBs and PP matrix, as shown in a scanning electron microscopy study. Fourier transform infrared analysis showed evidence of C?C and C?O bonds from MAH at 1630 and 1730 cm^?1, respectively. The MAH‐treated PP composites showed lower water absorption and thickness swelling than those with untreated EFBs. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 827–835, 2003     

Synthesis and analysis of PbO-modified Bi-Sr-Ca-Cu-O superconductors

High T _c superconducting materials based on a PbO-modified Bi-Sr-Ca-Cu-O system with various ratios between the oxides were prepared by calcination at 800 °C and firing at 855 °C. From X-ray powder diffraction analysis data, the ratio of low- and high-temperature phases was calculated. The material with the nominal composition Bi₂Pb_0.5Sr₂Ca_2.5Cu_3.5O _x was chosen for further experimental work. Samples fired at 800 °C contain mostly the low-temperature phase (2212). Higher firing temperatures lead to the formation of the high T _c phase (2223) with T _c(R=0) over 100 K. Some samples were cold pressed and refired which increased the specific density to over 80% of the theoretical density. The composition of samples was investigated by X-ray powder diffraction analysis and by energy dispersive X-ray spectroscopy. The main phase in the material fired at 800 °C, is the low T _c phase 2212, and secondary phases are Ca₂PbO₄, unreacted CuO and traces of 2223 phase. At higher firing temperatures, the main phase is the high-temperature phase 2223. The material is still heterogeneous and contains Ca₂PbO₄.     

WSDL and UDDI extensions for version support in web services

Versioning is an important aspect of web service development, which has not been adequately addressed so far. In this article, we propose extensions to WSDL and UDDI to support versioning of web service interfaces at development-time and run-time. We address service-level and operation-level versioning, service endpoint mapping, and version sequencing. We also propose annotation extensions for developing versioned web services in Java. We have tested the proposed solution for versioning in two real-world environments and identified considerable improvements in service development and maintenance efficiency, improved service reuse, and simplified governance.     

Electrochemical routes for environmentally friendly recycling of rare-earth-based (Sm–Co) permanent magnets

Journal of Applied Electrochemistry - The consumption of critical raw materials, especially those in permanent magnets of Nd–Fe–B and Sm–Co-type, has significantly grown in the...     

The effect of hexamethylene diisocyanate modified ALCELL lignin as a coupling agent on the flexural properties of oil palm empty fruit bunch – polypropylene composites

ALCELL lignin has been employed as a coupling agent in oil palm empty fruit bunch (EFB)–polypropylene (PP) composites. The lignin has been chemically modified with hexamethylene diisocyanate (HMDI). Evidence for the reaction between HMDI and lignin has been observed by using Fourier transform infrared (FTIR) analysis. The effect of lignin as a coupling agent on the flexural properties has been studied. The results show that the HMDI‐modified lignin is able to impart greater compatibility between EFB and PP. This is reflected in the greater flexural strength shown by the composites with HMDI‐modified lignin than those with the unmodified lignin. Scanning electron microscopy studies show that HMDI‐modification of lignin results in a better blending and compatibility between lignin and PP matrix. The glass transition temperature of lignin increases as the level of HMDI modification is increased. © 2001 Society of Chemical Industry     

Preliminary studies on the use of modified ALCELL lignin as a coupling agent in the biofiber composites

ALCELL lignin has been employed as a coupling agent in empty fruit bunch fiber (EFBF)–polypropylene (PP) composites. The lignin has been chemically modified with toluene diisocyanate (TDI) to various weight loadings. The evidence of the reaction between TDI and lignin has been observed by using Fourier transform infrared (FTIR) analysis. The effect of lignin as a coupling agent on mechanical properties has been studied. The results show that the TDI‐modified lignin is able to impart greater compatibility between EFBF and PP. This is reflected in the greater mechanical properties shown by the composites with TDI‐modified lignin than in those with the unmodified lignin. Scanning electron microscopy (SEM) studies showed that TDI modification of lignin resulted in a better blending and compatibility between lignin and PP matrix. The glass‐transition temperature of the lignin increases as the WPG is increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1333–1340, 2001