Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.     

Ideal amplifier spacing for reduction of Gordon-Haus jitter indispersion-managed soliton communications

Based on a variational analysis, the authors demonstrate that the noise-induced Gordon-Haus timing jitter in a dispersion-managed soliton transmission system can be substantially reduced by appropriate placement of the amplifiers     

Measurements of single chain form factors by small-angle neutron scattering from polystyrene blends containing high concentrations of labelled molecules

A series of small angle neutron scattering measurements on blends of normal polystyrene (PSH) and labelled (deuterated) polystyrene (PSD) have been made with concentrations of PSD from 5 to 50 mol %. It is shown that the single chain form factor of the polymer in bulk can be obtained from a single concentration measurement for any concentration of labelled molecules, providing the molecular weights of the parent and labelled molecules are the same and the molecular weight distributions are narrow.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Gordon-Haus timing jitter reduction in dispersion-managed solitoncommunications

An analytic theory is presented which demonstrates that the noise induced Gordon-Haus timing jitter in arbitrary dispersion-managed transmission systems is reduced by the power-enhancement factor required to support a dispersion-managed solitons provided the path-average soliton period is much greater than the dispersion-map period. The analysis further predicts the behaviour of the amplitude, width, and quadratic chirp fluctuations due to the amplified spontaneous emission (ASE) noise     

Channel-carrier mobility parameters for 4H SiC MOSFETs

In this paper, mobility parameters for enhancement-mode N-channel 4H SiC MOSFETs are extracted and implemented into 2-D device simulation program and SPICE circuit simulator. The experimental data were obtained from lateral N-channel 4H SiC MOSFETs with nitrided oxide–semiconductor interfaces, exhibiting normal mobility behavior. The presence of increasing interface-trap density (D_it) toward the edge of the conduction band is included during the 2-D device simulation. Using measured distribution of interface-trap density for simulation of the transfer characteristics leads to a good agreement with the experimental transfer characteristic.     

Simple approximations of the DC flux influence on the core losspower electronic ferrites and their use in design of magnetic components

The effect of DC flux on the core loss is examined for the practical range of power and frequency. Relevant core loss equations are derived and applied to an optimization algorithm to determine the minimum core loss at a given ratio of s (DC flux density to AC peak flux density). It has been found that the curves of hysteresis loss density versus the ratio of s exhibit a peak at a critical ratio. Below or above this critical ratio, the loss density decreases drastically. On the other hand, the curves of eddy-current loss density versus the ratio of s exhibits a minimum point at a critical ratio. Below or above this critical ratio, the loss density increases gradually     

A Web‐based and Group Learning Environment for Introductory Environmental Engineering

The use of computer‐based technology is becoming more prevalent in the classroom. As a part of an educational research project sponsored by the GE Foundation, strategies for augmenting a course, Introduction to Environmental Engineering (CE 280), were investigated including cross‐disciplinary experiences in teamwork, design, and the use of advanced teaching technologies such as the web. Interactive tools to assist student learning were developed and refined. Efforts have focused on developing an extensive website, web‐based quizzes and homework assignments, and tutorials. Base groups were used to provide both intellectual and emotional support to students. This paper summarizes the development of this course and the impact of rapid feedback on the progression of student understanding.