Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

Mode Matching Analysis of a Tapered Coaxial Tip in a Parallel-Plate Waveguide

A tapered coaxial tip in a parallel plate waveguide is investigated. A boundary-value problem of electromagnetic scattering from a tapered coaxial monopole is solved rigorously based on the Fourier transform, eigenfunction expansion, and mode matching. Scattering parameters are represented in a series and computed to understand the behavior of the scattering in terms of the coaxial tip geometry.     

用于实时数据传输的滑动帧方法及其实现

根据某雷达系统对测量信号的快速传输要求,提出采用滑动帧的处理方法并在FPGA中实现,克服了传统帧处理难以满足快速传输要求的不足。阐述了滑动帧结构的构造思想,详述了滑动帧结构的特点及具体功能模块的实现。根据实际应用需求构造了滑动帧结构处理器,试验和应用结果表明设计可行有效,能充分满足实时数据传输的要求。     

公司大门工程建设施工

大门小品建筑属多项目综合性工程。本文作者从管理者的角度 ,通过对公司大门及附属工程施工质量控制的总结 ,说明了质量控制应贯穿于工程施工的全过程     

论王光祈的“少年中国”理想

王光祈的“少年中国”理想，是以“少年意大利”为基础，汲取五四时期社会主义思潮的积极成分而形成的。创造“少年中国”在“人”的方面，是从改造中国少年入手，同时注重青年学生与平民的改造，注重劳动阶级、智识阶级与资产阶级的改造与联合；在“事”的方面，积极开展社会事业和社会活动，且必须经过社会分工与国际分工。可见，他的这种理想是典型的社会改革主张，在早期带有无政府主义色彩，自始至终具有强烈的民族主义情感。     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

���þ��ܰ�ȫ�Բ�������������

本文通过对在用钻机井架的现场实际测试,建立数据库、测评模型,对实测的数据用计算机技术进行分析,提出了初始弯曲应力;数据正态分布检验——x～2检验;建立回归方程;在给定置信度下测评当前承载能力的技术概念。解决了在用钻机A型井架的安全性评估问题,是一种较为合理、可靠、科学的测评技术和方法。     

Integrated scheduling of flexible manufacturing systems employingautomated guided vehicles

Centralized and distributed automated guided vehicle system (AGVS) models for materials handling, and the model for part processing are integrated into a single coherent model. This formulation can be used to collectively schedule and control the entire flexible manufacturing system (FMS) as opposed to the traditional separate scheduling of part processing and material handling. The two AGVS models are based on Petri nets and can be directly used in the scheduling method that uses Petri nets for formulation and heuristic search for solution. This method employs a global search to seek the optimal operation of an entire FMS. Scheduling examples are presented and the method compares favorably with the results simulated using heuristic dispatch rules