Spatiotemporal Magnetocaloric Microenvironment for Guiding the Fate of Biodegradable Polymer Implants

The degradation behavior of implants is significantly important for bone repair. However, it is still unprocurable to spatiotemporally regulate the degradation of the implants to match bone ingrowth. In this paper, a magneto-controlled biodegradation model is established to explore the degradation behavior of magnetic scaffolds in a magnetothermal microenvironment generated by an alternating magnetic field (AMF). The results demonstrate that the scaffolds can be heated by magnetic nanoparticles (NPs) under AMF, which dramatically accelerated scaffold degradation. Especially, magnetic NPs modified by oleic acid with a better interface compatibility exhibit a greater heating efficiency to further facilitate the degradation. Furthermore, the molecular dynamics simulations reveal that the enhanced motion correlation between magnetic NPs and polymer matrix can accelerate the energy transfer. As a proof-of-concept, the feasibility of magneto-controlled degradation for implants is demonstrated, and an optimizing strategy for better heating efficiency of nanomaterials is provided, which may have great instructive significance for clinical medicine.     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

ASYMPTOTIC PROPERTIES OF THE SAMPLE AUTOCORRELATIONS AND PARTIAL AUTOCORRELATIONS OF A MULTIPLICATIVE ARIMA PROCESS

Abstract. We shall investigate the asymptotic behaviour of the sample autocorrelations and partial autocorrelations of a multiplicative ARIMA process and derive their limiting distributions. Some simulations are presented to illustrate the results obtained.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Real-time measurement of pointing action by using DSP

This paper presents an approach of measuring in real-time the vector of finger that is pointing to an object. DSP is used in the operation processing unit in order to do the real-time processing. The steps include the extraction of flesh-colored regions from an image, the labeling of the flesh-colored regions, and the detection of two characteristic positions on the finger so that the direction that the finger is pointing at will be calculated. The entire process takes about 29 msec, which makes it possible to have the frame rate of 34 fps. With this frame rate, this measurement approach is considered real-time and promising to be merged into other application systems. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

A demonstrative study for the wind and solar hybrid power system

In March 1995, a small scale wind and solar hybrid power system was installed at Ashikaga Institute of Technology. Until now, the authors have acquired the data of the output of the hybrid power plant along with wind speed, wind direction, and the solar radiation, in order to demonstrate a complementary relationship between solar energy and wind energy.After nine months operation of the system, the authors confirmed that there exists a complementary relationship between solar energy and wind energy. We also found, however, that the power output by wind does not have much prospect compared to that by solar cell especially in summer season in Ashikaga area.     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

Paraneoplastic neurologic syndromes. 2. Lambert-Eaton myasthenic syndrome. 1) The molecular structure of calcium channel and immunology

The effect of divalent cations on the inactivation of Escherichia coli by high hydrostatic pressure was investigated. The presence of 0.5 mmol l-1 of CaCl2, MgCl2, MnCl2 and FeCl2 reduced pressure inactivation of E. coli MG1655, while 0.5 mmol l-1 of ZnCl2, NiCl2, CuCl2 and CoCl2 increased inactivation. Baroprotection by Ca2+ was found to be dose-dependent up to at least 80 mmol l-1 and was studied in more detail in terms of inactivation kinetics. Logarithmic survivor plots against time deviated from first order kinetics, suggesting that MG1655 cultures were heterogeneous with regard to pressure resistance. All cultures were shown to contain a small proportion of cells that were only slowly inactivated. Addition of Ca2+ increased the proportion of these tolerant cells in the cultures up to 1000-fold at 80 mmol l-1, but did not affect their inactivation rate. The addition of EDTA resulted in the opposite effect, lowering the proportion of pressure-tolerant cells in the cultures. Three pressure-resistant mutants of E. coli MG1655 were found to be more resistant to EDTA under pressure compared with MG1655, and were unaffected by Ca2+ under pressure. In addition, these mutants had a 30-40% lower Ca2+ content than MG1655. Based on these results, it is postulated that pressure killing of E. coli MG1655 is mediated primarily by the destabilization of Ca(2+)-binding components, and that the mutations underlying pressure resistance have resulted in pressure-stable targets with reduced Ca(2+)-binding affinity.     

Preparation of rod-shaped BaTiO3 powder

Rod-shaped BaTiO₃ powder particles have been prepared from rod-shaped TiO₂ ·nH₂O and BaCO₃ in molten chloride. The morphology of BaTiO₃ particles was studied referring to the effects of the chemical species of the starting titanium compound, amount of chloride, particle size of the titanium compound and reaction conditions, and the preparation condition of rod-shaped BaTiO₃ has been determined: i.e., large TiO₂ ·nH₂O particles were heated at 700°C in molten salt with an equal amount of BaTiO₃. This condition was effective in suppressing the formation of BaTiO₃ by a solution-precipitation process as well as the deformation of either TiO₂ ·nH₂O or BaTiO₃, which are responsible for the formation of equiaxed BaTiO₃ particles. The obtained rod-shaped BaTiO₃ particles had a cubic symmetry. Electron diffraction analysis showed that the following topotactic relation is retained; 0 1 0_{potassium tetratitanate} 0 1 0_{hydrated titania} 1 0 0_anatase 1 0 0_{barium titanate}     

Formation of Small-Sized CdSxSe1-x Crystals in Sol-Gel-Derived SiO2 Glasses

Silica glasses doped with small-sized CdS_x-Se_1-x crystals were prepared by the sol-gel method. Gels synthesized by the hydrolysis of Si(OC₂H₅)₄, in the presence of CdSeO₄ with NH₄SCN dissolved in HNO₃ or NH₄OH, were heated in H₂-N₂ atmosphere. The pH value of solutions for CdSeO⁴ and NH⁴SCN primarily determined the fraction of anions in CdS^xSe^1-x crystals. The anion content in crystals was dependent on the pH value of the solvent and/or heat-treatment temperature, and the sulfur fraction changed from 0.1 to 0.6. The optical absorption spectra were red-shifted as the selenium content and the crystal size increased, and the emission spectra showed a sharp band near the absorption edge position and a broad tail extending into the long wavelength. The optical band gap energies increased reciprocally proportional to the square of the crystal size.