Membrane separation of indigenous noroviruses from sewage sludge and treated wastewater.

In this study, feasibility of membrane separation for the removal of indigenous noroviruses (NVs) is evaluated. The indigenous NV gene was never detected from ultrafiltration (UF) permeates of sewage sludge and treated wastewater. Indigenous NV gene was also not detected from permeates of sewage sludge and treated wastewater by microfiltration (MF) with a pore size of 0.1 microm (MF0.1). Even though the pore size of MF (0.1 microm) was much larger than the diameter of virus particle (approximately 30-40nm), more than 4-log10 reduction value (LRV) at maximum was achieved by membrane separation with MF0.1. NV genes were often detected from permeates of sewage sludge and treated wastewater by MF with a pore size of 0.45 microm (MF0.45), although the maximum log10 reduction values were more than 3.59 for sewage sludge and more than 2.90 for treated wastewater. It is important to verify factors determining the removal efficiency of viruses with MF membranes.     

Effect of light source spectral modulation on wavelength interrogation in fiber Bragg grating sensors and its reduction

In the fiber Bragg grating sensing using a superluminescent diode as the light source and an arrayed waveguide grating as the wavelength interrogator, the wavelength measurement error due to the spectral modulation of the superluminescent diode is theoretically formulated and quantitatively analyzed by computer simulation. It is shown that the wavelength measurement errors produced with the use of real superluminescent diodes are in very good agreement with the theoretical results. In order to reduce the wavelength measurement error due to the spectral modulation of superluminescent diode, two different types of remedies are proposed that utilize the temperature switching of superluminescent diode and that adjust the bandwidths of fiber Bragg grating and arrayed waveguide grating, and their efficacies are experimentally demonstrated together with good quantitative agreement with the theoretical calculation.     

Geochemical characteristics of the Yufuin outflow plume, Beppu hydrothermal system, Japan

Thermal water at Yufuin (Kyushu Island, Japan) is tapped through about 820 shallow wells and used mainly for hot-spring bathing purposes. Chemical and isotopic data for fluids from wells and fumaroles in Yufuin and Beppu indicate that the thermal activity at Yufuin represents a dilute, westward-flowing hydrothermal outflow plume from the Beppu hydrothermal system. Two other (eastward-flowing) outflow plumes have long been recognized at Beppu, but the Yufuin outflow plume is first recognized here. The Yufuin outflow plume is apparently a mixture of two end-member fluids: (1) deep high-temperature (250–300°C) fluid from the Beppu system having high chloride concentration (1400–1600 mg/L) and a δ¹⁸O value near −6.0%, and (2) meteoric water having low chloride concentration (≤7 mg/L) and a δ¹⁸O value near −9.2%.A permeable conduit for the vertical and lateral transport of deep fluid from the Beppu system is provided by the Yufuin Fault zone, which extends westward from the southern flank of Mt. Tsurumi volcano to the town of Yufuin. Stable isotope ratios and chloride concentrations for shallow groundwaters near the eastern end of the fault, at an elevation near 700 m, are consistent with those required for the low-chloride meteoric end-member of the Yufuin thermal waters. Recharge of this meteoric water, as well as mixing with the Beppu deep fluid, may occur along the Yufuin Fault. Enthalpy-chloride relations indicate additional conductive heating of the Yufuin waters, in the amount of 350–500 kJ/kg beyond that which can be accounted for by mixing between Beppu deep fluid and meteoric water. This could be a result of conductive heating with convection to a depth of 1–2 km. Estimates of the magnitude of the heat source for the Beppu hydrothermal system should take into account the heat being discharged at Yufuin.     

Ulcerative colitis with skip lesions at the mouth of the appendix: a clinical study

OBJECTIVE: We examined the clinical characteristics of ulcerative colitis patients who demonstrated endoscopically discontinuous lesions at the mouth of the appendix. METHODS: Of patients with initial or recurrent active ulcerative colitis who underwent total colonoscopy during the past 3 yr at Osaka City General Hospital, we selected those who had skip lesions in the mouth of the appendix before treatment, and examined their gender, age, disease type, sites of lesions, inflammatory reaction, severity of disease, effects of treatment, and posttreatment course. RESULTS: Discontinuous lesions at the mouth of the appendix were found in 10 patients, who had the following common clinical features: the major lesion was usually present in the lower part of the large bowel including the rectum, many of the patients had suffered an initial attack only, all patients had mild disease, and many of the patients responded quite satisfactorily to treatment with salicylazosulfapyridine. CONCLUSION: Numerous patients with ulcerative colitis with discontinuous lesions at the mouth of the appendix were observed and their clinical characteristics were examined. Determination of the clinical significance of skip lesions in the appendix will contribute to elucidation of the pathogenesis of ulcerative colitis.     

Feedback control of decoupled bending and torsional vibrations of flexible beams

In this article, we consider a flexible beam with a rigid body, of which the bending vibration and the torsional vibration are decoupled. Therefore we need two control motors to suppress the vibrations. Each set of dynamic equations is treated in the form of an appropriate Hilbert space. A stabilizing feedback control law of each rotation motor will be established on the basis of modal analysis. A set of experiments has been carried out, and the results demonstrate the effectiveness of the dynamic model and the proposed control law. © 1994 John Wiley & Sons, Inc.     

High-efficiency finishing process for metal mold by large-area electron beam irradiation

A new finishing process for metal molds by large-area electron beam (EB) irradiation is proposed in this study. In the large-area EB irradiation equipment used here, an EB with high-energy density is irradiated without focusing the beam, and so the EB with a maximum diameter of 60 mm can be used for melting or evaporating metal surface instantly. Experimental results show that the surface roughness decreases from 6 μmRz to less than 1 μmRz in just a few minutes under proper machining conditions. The corrosion resistance of metal mold surface also could be greatly improved by large-area EB irradiation. Furthermore, the surface roughness of tilting surface close to 90° could be well improved. Therefore, large-area EB irradiation method has a possibility to become a high-efficiency finishing process for metal molds.     

Stabilization of bioethanol recovery with silicone rubber‐coated ethanol‐permselective silicalite membranes by controlling the pH of acidic feed solution

In order to produce highly concentrated bioethanol by pervaporation using an ethanol‐permselective silicalite membrane, techniques to suppress adsorption of succinic acid, which is a chief by‐product of ethanol fermentation and causes the deterioration in pervaporation performance, onto the silicalite crystals was investigated. The amount adsorbed increased as the pH of the aqueous succinic acid solution decreased. The pervaporation performance also decreased with decreasing pH when the ternary mixtures of ethanol/water/succinic acid were separated. Using silicalite membranes individually coated with two types of silicone rubber, pervaporation performance was significantly improved in the pH range of 5 to 7, when compared with that of non‐coated silicalite membranes in ternary mixtures of ethanol/water/succinic acid. Moreover, when using a silicalite membrane double‐coated with the two types of silicone rubber, pervaporation performance was stabilized at lower pH values. In the separation of bioethanol by pervaporation using the double‐coated silicalite membrane, removal of accumulated substances having an ultraviolet absorption maximum at approximately 260 nm from the fermentation broth proved to be vital for efficient pervaporation. Copyright © 2005 Society of Chemical Industry     

The temperature dependence of luminescence from a long-lasting phosphor exposed to ionizing radiation

The temperature dependence of luminescence from a long-lasting phosphor (LLP), SrAl₂O₄ : Eu²⁺,Dy³⁺, exposed to ionizing radiation has been measured to understand the LLP luminescence mechanism. Evaluation of the decay constants of the LLP exposed to -, β- or γ-rays at temperatures from 200 to 390 K showed that the decay constant is divided into four components ranging from 10⁻⁴ to 10⁻¹ s⁻¹ with activation energies of 0.02–0.35 eV.

Total luminous intensity from the LLP with changing irradiation temperature has its maximum value around the room temperature. Irradiation at elevated temperature (390 K) has the total luminescence pattern with monotonous decrease as temperature rises. As a result of evaluating the temperature dependence of luminescence, the luminescence mechanism is considered as follows:

Full-size image