Effect of puffer volume and operating force on dielectric recovery performance in thermal puffer-type gas circuit breaker

In order to investigate the influence of puffer volume V/sub P/ and operating force to dielectric performance of GCB at current interruption, we calculated the prospective dielectric withstand voltage V/sub W/ between arcing contacts. The withstand voltage was calculated by the electric field strength appeared on arcing contacts and the allowable electric field strength E/sub W//sup */ of hot gas due to thermal puffer action. We could clarify that large initial puffer volume V/sub P/ can increase withstand voltage V/sub W/ at current breaking point and also that an optimum point exists in operating force F. For example, it was found that in case of the operating force of 1000 kgf, the puffer volume V/sub P/ of 1.2 liter would be best choice in the interrupting condition of i=50 kA and arcing time of 1.35 cycle.     

Two patients with polymyositis or dermatomyositis complicated with massive pleural effusion

Two patients with polymyositis (PM) or dermatomyositis (DM) complicated with massive pleural effusion are reported here. Both patients presented a high-grade fever, pleural effusion prominent on the right, and good response to steroid therapy. In a 50-year-old woman with PM, combined process of pleural inflammation, cardiomyopathy and coexisting hypothyroidism were considered to be responsible for the accumulation of the massive pleural effusion. However, in a 34-year-old man with DM, pleural inflammation associated with interstitial pneumonia or pleural microvasculopathy in DM was considered to be responsible for the accumulation of the massive pleural effusion.     

Adsorption of urea,creatinine, and uric acid from three solution types using spherical activated carbon and its recyclability

In this paper, we propose that the urinary toxins from the wastewater be adsorbed on an adsorbent such as spherical activated carbon and the latter be regenerated by subjecting it to high temperatures to recycle activated carbon and also to recycle the water used in dialysis. We studied the adsorption of artificial waste dialysate, which is a mixed solution of urea, creatinine, and uric acid, and the separate solutions for each of these and found that their extents of adsorption onto the spherical activated carbon material were nearly identical. The amount of adsorption was approximately 1.4 mg·g^-1 for urea, 18 mg·g^-1 for creatinine, and 20 mg·g^-1 for uric acid. The urea, creatinine, and uric acid adsorbed onto the spherical activated carbon decomposed on heat treatment at 500℃, and the adsorption capacity of the spherical activated carbon was regenerated. Our study successfully demonstrated that the spherical activated carbon can be recycled in the waste dialysate treatment process.     

The behavior of a swarm of particles moving in a viscous fluid

A significant bulk flow is thought to occur if a part of the body of a suspension, which has a different density from the density of the remainder of the suspension, is large enough in space however slight the difference may be. As a typical case, the slow motion of a swarm of particles in a viscous fluid was studied both theoretically and experimentally. Under a certain condition, the suspended particles formed a drop of suspension, in which the suspended particles and fluid moved as one body in the same way. The falling velocity of a spherical swarm of particles, which was called a drop of suspension, was measured and compared with a new theoretical prediction presented in this paper.It may be also noted that the theoretical model may be applicable to the flow due to density difference by means of replacement of the continuous mass by the damped mass which is regarded as consisting of particles.     

Sintering of Ceria-Doped Tetragonal Zirconia Crystallized in Organic Solvents, Water, and Air

Amorphous CeO₂–ZrO₂ gels were prepared by coprecipitation in ammonia solutions. The onset of crystallization of the gels, from calcining in air, was 420°C, while 200° to 250°C in the presence of water and organic solvents such as methanol and ethanol. The sintering behaviors of CeO₂–ZrO₂ powders were sensitive to the crystallizing conditions, since hard agglomerates formed when the precipitated gels were crystallized by normal calcination in air, whereas soft agglomerates formed when they were crystallized in water or organic solvents. CeO₂–ZrO₂ powders crystallized in methanol and water at 250°C were sintered to full theoretical density at 1150° and 1400°C, respectively, whereas that crystallized by calcination in air at 450°C was sintered to only 95.2% of theoretical density, even at 1500°C.     

Liquefaction of wood in the presence of phenol using phosphoric acid as a catalyst and the flow properties of the liquefied wood

The liquefaction of wood in the presence of phenol using phosphoric acid as a catalyst and the flow properties of the obtained liquefied wood were investigated. It was found that phosphoric acid is a satisfactory catalyst for liquefying wood. The amount of phenol that reacts with the liquefied wood components (i.e., combined phenol) increases with an increase in liquefaction temperature, liquefaction time, catalyst content, or liquid ratio. By removing the free phenol, the resulting liquefied woods become novolaclike resins. The measurements of the flow properties of these liquefied woods reveal that the melts of liquefied woods behave as pseudoplastics and their flows obey the Ostwald de Waele power law equation. The amount of combined phenol within the liquefied wood and the presence of filler in the liquefied wood have great influence on their flow properties. The flowing temperature, activation energy, and zero shear viscosity of the liquefied woods show tendencies to increase with an increase in combined phenol. © 1994 John Wiley & Sons, Inc.     

Morphological study by TEM on uniaxially oriented thin films of PET, PEN and their blends

Uniaxially oriented thin films of poly(ethylene terephthalate) (PET), poly(ethylene 2,6-naphthalene dicarboxylate) (PEN) and their blends were prepared by applying shear strain to their respective melts, and the resulting morphologies were studied by transmission electron microscopy. Selected-area electron diffraction of each film revealed well-defined uniaxial orientation of polymer chains in the shearing direction. In the uniaxially oriented thin film of PEN, stacked-lamellar structure with the average long period of 27 nm consisting of a crystalline region about 15 nm thick and an amorphous one about 12 nm thick was found here and there in the dark-field image: PEN-type. On the other hand, stacked-lamellar structure was rarely observed in the case of PET: PET-type. In PET/PEN blends, the morphologies changed from the PET-type to the PEN-type with increasing content of PEN.     

A multi-objective strategy in genetic algorithms for gene selection of gene expression data

A microarray machine offers the capacity to measure the expression levels of thousands of genes simultaneously. It is used to collect information from tissue and cell samples regarding gene expression differences that could be useful for cancer classification. However, the urgent problems in the use of gene expression data are the availability of a huge number of genes relative to the small number of available samples, and the fact that many of the genes are not relevant to the classification. It has been shown that selecting a small subset of genes can lead to improved accuracy in the classification. Hence, this paper proposes a solution to the problems by using a multiobjective strategy in a genetic algorithm. This approach was tried on two benchmark gene expression data sets. It obtained encouraging results on those data sets as compared with an approach that used a single-objective strategy in a genetic algorithm. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008