A comparative study on structural,morphological and photocatalytic properties of anodically grown ZnO nanowires under varying parameters

Journal of Materials Science: Materials in Electronics - In this study, zinc oxide (ZnO) nanowires (NWs) were successfully produced on Zn plates through electrochemical anodization in potassium...     

Tribological properties and studies in SBF of Ta2O5/TiN/TiO2 monolayer and bilayer coatings on biomedical Ti6Al4V alloy

In this study, Ta₂O₅, TiN, and TiO₂ are coated with magnetron sputtering method as monolayer and bilayer on Ti6Al4V alloy used in biomedical applications. The deposited coatings are characterized, and their mechanical properties are determined by nanoindentation tests. As a result of the pin-on disc wear test performed in dry environment and room temperature, in vitro corrosion test was applied to the samples with high wear resistance, and the information about the tribological properties was obtained. Experimental results show that the existence of the intermediate layer has also significant effect on the corrosion resistance of the coatings. The biocompatibility of the Ta₂O₅/TiO₂ coating was examined by keeping it in simulated body fluid (SBF) due to its noticeable wear and corrosion resistance properties, the growth of apatite, which is described as an indicator of biocompatibility, occurred on the sample surface after 7 day.

     

Production,characterization and optimization of thermoelectric module and investigation of doping effects on thermoelectric performances

The objective of this study is to produce the thermoelectric (TE) module called as a Peltier module or element using new and promising materials that work at high temperature for generation of electricity with thermoelectric energy conversion from waste heat at high temperatures. Peltier modules used commercially nowadays can work at relatively low temperatures and their efficiency increase in proportion to the temperature difference between the surfaces of the modules. They consist of a pair of p- and n-type semiconductor. In this study, calcium cobalt oxide was chosen as a p-type semiconductor whilst zinc oxide was chosen as n-type semiconductor. Pure and aluminum-doped zinc oxide and silver-doped calcium cobalt oxide powders were synthesized via sol–gel processing successfully. The obtained powders were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), fourier transform infrared (FTIR), differential thermal analysis-thermogravimetry (DTA-TG), and scanning electron microscopy (SEM). In addition, the particle size distribution of the powders obtained via sol–gel processing was determined using a particle size analyzer. One and two leg oxide thermo-electric modules consisting of one pair of p-type 0.03 percent silver doped calcium cobalt oxide and n-type 0.02 percent aluminum doped zinc oxide bulks of 25 square millimeter cross-section and 3 millimeter heights were constructed. The thermoelectric module constructed was tested at high temperatures, and compared to other similar oxide modules reported in literature. Ultimately, the thermal stress and alteration of thermal stress depending on the leg length and side length of semiconductors were calculated using the finite element analysis (FEA) model in ANSYS 15.0 software. According to the results of the analysis, TE module was optimized in terms of mechanical behavior.     

Graphene and carbon black filled conductive nanocomposite films for heating element applications

Graphene has ultra-high electrical and thermal conductivity, which makes graphene as the most encouraging fillers for thermally conductive composites. Graphene and/or carbon black filled conductive polymer composite (CPC) films used as heating element are smarter than the traditional heating elements due to less environmental pollution, ease of application on many surfaces and possess the merits of lightweight. In this study, we investigated mainly the production, characterization and industrial application of graphene/carbon black reinforced styrene acrylic copolymer emulsion matrix composite films deposited on polyvinyl chloride for flexible heating element. After that, the films were dried at room temperature for 24 h in air. Structural and surface properties of the CPC films were characterized by X-ray diffraction and scanning electron microscopy. Temperature, time and voltage relation of the produced composite films were investigated. Heating and electrical properties of the CPC films were determined by using a thermal camera and 4-point probe measurement system, respectively. The electrical resistivity of the CPC films decreases from ~?10⁸ to 10¹ Ω cm with increasing the filler content or using a combination of two fillers. Graphene and carbon black filled conductive polymer composites to be considered as candidates for flexible heating element applications exhibited good electrical and heating properties thanks to synergistic effect of fillers.     

A Comparison on Physical,Structural, and Photocatalytical Properties of TiO2 Nanopowders Produced Using Sol‐Gel and Flame Spray Pyrolysis

In this study, nanoscale photocatalyst TiO₂ powders were synthesized via sol‐gel and flame spray pyrolysis (FSP). Phase structures and ratios were analyzed by X‐ray diffractometer (XRD). Size, specific surface area, and morphologies were determined using particle size analyzer, Brunauer‐Emmett‐Teller theory, and scanning electron microscope, respectively. Anatase phase with some rutile together was obtained in XRD analysis. The degradation rates of aqueous methylene blue (MB) by TiO₂ nanopowders were calculated using UV–vis spectrophotometer. It was found that MB decomposition was successfully achieved with significantly high efficiencies for both sol‐gel and FSP‐derived powders with small differences.     

The effects of growth conditions on the surface properties and photocatalytic activities of anatase TiO<Subscript>2</Subscript> films prepared via electrochemical anodizing and annealing methods

In the present work, nanostructured TiO₂ films were prepared by electrochemical anodization process of titanium in fluoride-containing electrolytes using an innovative approach. After anodization, the TiO₂ films were annealed at 480?°C for 2 h in air in order to acquire anatase phase transformation and increase its crystallinity. The effects of anodization voltage, electrolyte concentration and anodization time on the formation of TiO₂ films and the photocatalytic degradation of methylene blue (MB) were discussed in details. The phase structure and surface morphology of the samples characterized by means of X-ray diffraction and scanning electron microscope. The as-prepared nanostructured TiO₂ film anodized in 0.5% HF electrolyte at 15 V for 240 min showed excellent photocatalytic degradation of MB and is promising for environmental purification.     

Effects of annealing on the structural and magnetic properties of flame spray pyrolyzed MnFe2O4 nanoparticles

In this study, manganese ferrite (MnFe₂O₄) nanoparticles were produced through flame spray pyrolysis (FSP). To investigate the effects of heat treatment, the nanoparticles were annealed between 400 and 650°C for 4 h in air in a comparative manner. The structural, chemical, morphological, and magnetic properties of the nanoparticles were evaluated using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), dynamic light scattering (DLS), and vibrating sample magnetometry (VSM), respectively. The XRD results showed that the nanoparticles synthesized by the FSP method exhibited the MnFe₂O₄ spinel ferrite structure. The annealing process led to the decomposition of MnFe₂O₄ into various phases. According to the morphological analysis, the as-synthesized particles were hemispherical–cubic in shape and had an average particle size of less than 100 nm. In addition, the chemical bond structures of the nanoparticles were confirmed in detail by XPS elemental analysis. The highest saturation magnetization was recorded as 33.50 emu/g for the as-produced nanoparticles. The saturation magnetization of the nanoparticles decreased with increasing annealing temperature, while coercivity increased.