Effect of Milling on Slip Casting of Partially Stabilized Zirconia

Specimens of partially stabilized zirconia were slip cast from aqueous suspensions and sintered at 1500°C for 3 h. The relative density of the cast specimens and the firing shrinkage of the sintered specimens depend on the milling time for the suspension. Vickers hardness and K_IC values of 11.46±s0.07 GN/m² and 6.10 ±0.04 MN.m^3/2, respectively, were obtained for all sintered specimens. The dispersion of the suspension is important in increasing the relative density of the cast specimens.     

A novel technique for a DC brushless motor without position sensors

A dc brushless motor is a kind of synchronous motor driven by an inverter and requires sensors to detect the rotor position. As one of the methods, the induced voltages of a brushless motor have been utilized in practice. However, there are some problems in this method, e.g., the motor can obtain insufficient torque due to the low induced voltages in a low-speed range. This paper proposes a new method which controls the inverter angular frequency ω₁ by using inherent characteristics wherein the torque current i_r is almost proportional to the internal phase angle φ where the primary flux of a synchronous motor is controlled to be constant. If the parameters of a motor are given exactly, the speed regulation is quite small and the transient characteristics with high response and high starting torque are obtained. Furthermore, it is possible to operate a synchronous motor in the field-weakening range. Here, the principle of the control method and the performance characteristics of a dc brushless motor having no position sensors are discussed. The simulation and the experimental results of the tested machine show that the proposed method is very useful for practical applications.     

Adaptive covariate acquisition for minimizing total cost of classification

Machine Learning - In some applications, acquiring covariates comes at a cost which is not negligible. For example in the medical domain, in order to classify whether a patient has diabetes or not,...     

Microscopic structure of athabasca oil sand

A refined structural model for in situ oil sands is proposed in terms of the mutual arrangement of sand grains, fines, water and bitumen. In the Athabasca deposit, the sand grains consist mainly of quartz and their packing is such that the porosity is about 35%. In rich oil sand, 10–15% of the pore space is occupied by connate water whereas the remainder is occupied by bitumen. For lower grade oil sands, a direct correlation exists between the water content and the amount of fines (particles smaller than 44 μm) and an inverse correlation exists between the bitumen content and the amount of fines. These relationships are successfully explained in terms of the irreducible water saturation in a porous medium and the double layer interaction between sand and bitumen surfaces.     

Potential bile acid metabolites. 24. An efficient synthesis of carboxyl-linked glucosides and their chemical properties

A facile and efficient synthesis of the carboxyl-linked glucosides of bile acids is described. Direct esterification of unprotected bile acids with 2,3,4,6-tetra-O-benzyl-d-glucopyranose in pyridine in the presence of 2-chloro-1,3,5-trinitrobenzene as a coupling agent afforded a mixture of the α- and β-anomers (ca. 1∶3) of the 1-O-acyl-d-glucoside benzyl ethers of bile acids, which was separated effectively on a C₁₈ reversedphase chromatography column (isolated yields of α- and β-anomers are 4–9% and 12–19%, respectively). Subsequent hydrogenolysis of the α- and β-acyl glucoside benzyl ethers on a 10% Pd−C catalyst in acetic acid/methanol/EtOAc (1∶2∶2, by vol) at 35°C under atmospheric pressure gave the corresponding free esters in good yields (79–89%). Chemical specificities such as facile hydrolysis and transesterification of the acyl glucosides in various solvents were also discussed.     

Reprint of “Suppressing propylene carbonate decomposition by coating graphite electrode foil with silver”

A method has been developed to suppress the decomposition of propylene carbonate (PC) by coating graphite electrode foil with a layer of silver. Results from electrochemical impedance measurements show that the Ag-coated graphite electrode presents lower charge transfer resistance and faster diffusion of lithium ions in comparison with the virginal one. Cyclic voltammograms and discharge-charge measurements suggest that the decomposition of propylene carbonate and co-intercalation of solvated lithium ions are prevented, and lithium ions can reversibly intercalate into and deintercalate from the Ag-coated graphite electrode. These results indicate that Ag-coating is a good way to improve the electrochemical performance of graphitic carbon in PC-based electrolyte solutions.     

Control of secondary flow in concentrically traveling flow on centrifugal microfluidics

This paper reports a fundamental study of the stripe laminar flow pattern on a centrifugal microfluidic device with the goal of realizing a sedimentation-based, continuous mode particle separation technique. Microfluidic channels were designed with a concentrically integrated microchannel, and the patterning of the flow in the channel was investigated. A significant secondary flow was observed as a preliminary result. We conclude that the origin of this secondary flow was not the Dean force, because it was observed in a straight microchannel, but was not observed in curved channel during the spinning of the system at rest. The transition of the pattern was investigated using a simulation and experiment, and the flow pattern’s dependence on the rotational speed was determined, which suggested that the origin of the secondary flow was the Coriolis force. The significance of the secondary flow was controlled by adjusting the rotational speed of the disk, and the flow rate and laminar flow patterns were controlled by the stripe flow pattern.     

Application of an ultrahigh-resolution scanning electron microscope (UHS-T1) to biological specimens

In 1985 we developed an ultrahigh-resolution scanning electron microscope with a resolution of 0.5 nm. It is equipped with a field emission gun and an objective lens with a very short focal length. In this study we report a survey of some different preparation techniques and biological specimens using the new scanning electron microscope. Intracellular structures such as cell organelles were observed surprisingly sharper than those observed by ordinary scanning electron microscopes. However, at magnifications over 250,000 X, platinum particles could be discerned as scattered pebbles on the surface of all structures in coated materials. Using an uncoated but conductively stained specimen, we successfully observed ribosomes on a rough endoplasmic reticulum at a direct magnification of 1 million. In these images some protrusions were recognized on the ribosomes. Ferritin and immunoglobulin G were used as samples of biological macromolecules. These samples were observed without metal coating and conductive staining. The ferritin particles appeared as rounded bodies without any substructure on the surface and immunoglobulin G as complexes of three-unit bodies. In the latter the central body might correspond to the Fc fragment and two side ones to Fab fragments. We assume that ultrahigh-resolution scanning electron microscopy is an effective means for observation of the cell fine structures and biological macromolecules. It will open a new research field in biomedicine.     

Stereocomplex crystallization and spherulite growth behavior of poly(l-lactide)-b-poly(d-lactide) stereodiblock copolymers

The non-isothermally and isothermally crystallized stereodiblock copolymers of poly(l-lactide) (PLLA) and poly(d-lactide) (PDLA) with equimolar l-lactyl and d-lactyl units and different number-average molecular weights (M_n) of 3.9 × 10³, 9.3 × 10³, and 1.1 × 10⁴ g mol⁻¹, which are abbreviated as PLLA-b-PDLA copolymers, contained only stereocomplex crystallites as crystalline species, causing higher melting temperatures of the PLLA-b-PDLA copolymers compared to those of PLLA homopolymers. In the case of non-isothermal crystallization, the cold crystallization temperatures of the PLLA-b-PDLA copolymers during heating and cooling were respectively lower and higher than those of PLLA homopolymers, indicating accelerated crystallization of PLLA-b-PDLA copolymers. In the case of isothermal crystallization, in the crystallizable temperature range, the crystallinity (X_c) values of the PLLA-b-PDLA copolymers were lower than those of the PLLA homopolymers, and were susceptible to the effect of crystallization temperature in contrast to that of homopolymers. The radial growth rate of the spherulites (G) of the PLLA-b-PDLA copolymers was the highest at the middle M_n of 9.3 × 10³ g mol⁻¹. This trend is different from that of the PLLA homopolymers where the G values increased monotonically with a decrease in M_n, but seems to be caused by the upper critical M_n values of PLLA and PDLA chains as in the case of PLLA/PDLA blends (in other papers), above which homo-crystallites are formed in addition to stereocomplex crystallites. The disturbed crystallization of PLLA-b-PDLA copolymers compared to that of the PLLA/PDLA blend is attributable to the segmental connection between the PLLA and PDLA chains, which interrupted the free movement of those chains of the PLLA-b-PDLA copolymers during crystallization. The crystallite growth mechanism of the PLLA-b-PDLA copolymers was different from that of the PLLA/PDLA blend.     

Electrochemical reaction of the SiMn/C composite for anode in lithium ion batteries

The SiMn-graphite composite powder was prepared by mechanical ball milling and its electrochemical performances were evaluated as the candidate anode materials for lithium ion batteries. It is found that the cyclic performance of the composite materials is improved significantly compared to SiMn alloy and pure silicon. The heat treatment of the electrodes is beneficial for enhancing the cyclic stabilities. The SiMn-20 wt.% graphite composite electrode after annealing at 200 °C has an initial reversible capacity of 463 mAh g⁻¹ and a charge-discharge efficiency of 70%. Moreover, the reversible capacity maintains 426 mAh g⁻¹ after 30 cycles with a coulomb efficiency of over 97%. The phase structure and morphology of the composite were analyzed by X-ray diffraction (XRD) and scanning electron microscopy. The lithiation/delithiation behavior was investigated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. The composite materials appear to be promising candidates as negative electrodes for lithium rechargeable batteries.