Effect of Cobalt and Nickel Doping on Structural and Magnetic Properties of Iron Oxide Nanoparticles

Two series samples of Iron Oxide nanoparticles doped with nickel and cobalt with different doping values (x?=?0.01; 0.03; 0.05 and 0.07), were successfully synthesized by using sol–gel method, and then they were characterized by X-ray diffraction, scanning electron and vibrating sample magnetometer (VSM). X-ray diffraction analysis of two series samples showed the formation α-Fe₂O₃ nanoparticles, accompanied by two phases iron spinels, CoFe₂O₄ and NiFe₂O₄. In addition, the variations in grain size were observed for both two series. The observation by scanning electron microscopy reveals a change in the morphology of the grains of all the samples doped, which confirm the cobalt and nickel effect on the morphology of iron oxide nanoparticles. Magnetic measurements which were measured by VSM showed significant magnetic parameters such as coercivity and magnetization besides the ferromagnetic behavior of both two series doped with Cobalt and Nickel.

     

Study of Undoped and Indium Doped ZnO Thin Films Deposited by Sol Gel Method

Silicon - In this paper, we report the effects of Indium doping concentrations (from 0 to 10wt%) on the structural, morphological, and optical properties of deposited In doped ZnO (IZO) thin films...     

Preparation of Sb:SnO2 thin films and its effect on opto-electrical properties

The present study focuses on pure and antimony (Sb)-doped tin oxide thin film and its influence on their structural, optical, and electrical properties. Both undoped and Sb-doped SnO₂ thin films have been grown by using simple, inexpensive pyrolysis spray technique. The deposition temperature was optimized to 450 °C. X-ray diffractions pattern have revealed that the films are polycrystalline and have tetragonal rutile-type crystal structure. Undoped SnO₂ films grow along (110) preferred orientation, while the Sb-doped SnO₂ films grow along (200) direction. The size of Sb-doped tin oxide crystals changes from 26.3 to 58.0 nm when dopant concentration is changed from 5 to 25 wt%. The transmission spectra revealed that all the samples are transparent in the visible region, and the optical bandgap varies between 3.92 and 3.98 eV. SEM analysis shows that the surface morphology and grain size are affected by the doping rate. All the films exhibit a high transmittance in the visible region and show a sharp fundamental absorption edge at about 0.38–0.40 nm. The maximum electrical conductivity of 362.5 S/cm was obtained for the film doped with 5 wt% Sb. However, the carrier concentration is increased from 0.708?×?10¹⁸ to 4.058?×?10²⁰ cm³. The electrical study reveals that the films have n-type electrical conductivity and depend on Sb concentration. We observed a decrease in sheet resistance and resistivity with the increase in Sb dopant concentration. For the dopant concentration of 5 wt% of Sb in SnO₂, the Rs and ρ were found minimum with the values of 88.55 (Ω cm^?2) and 2.75 (Ω cm), respectively. We observed an increase in carrier concentration and a decrease in mobility with the addition of Sb up to 25 wt%. The highest figure of merit values 2.5?×?10^–3 Ω^?1 is obtained for the 5wt% Sb, which may be considered potential materials for solar cells' transparent windows.

     

Modelling of a hybrid photovoltaic thermal collector based on CdTe

A few years ago, silicon photovoltaic panels had yields of 10 to 18%, which made them interesting because is not profitable enough (too expensive to energy conversion yield too low).But recently, thin film technology appears to increase the efficiency and reduce the cost. For application in hybrid collectors, various types of solar photovoltaic hybrid collectors (PVT) based on new materials for solar cells have been developed as the binary semiconductor, ternary and quaternary materials and organic. CdTe is a the most appropriate binary materials for use in photovoltaic structures in thin layers, this material can produce a high yield of about 15% and is also known by a direct band structure gap of a value of 1.45 eV and a very high absorption coefficient (>105 cm^–1 in the visible). In this work we present the modeling of a hybrid photovoltaic thermal collector based on the thin films solar cells of CdTe, and then we made the determination of the temperature levels of the various layers through the development of the energy balance sheet involves heat exchange between the different components of the collector and to study its electrical and thermal performance, and finally compare their efficiency with it of the PVT collector based on monocrystalline silicon.     

Influence of precursor source on sol–gel deposited ZnO thin films properties

Zinc oxide thin films were deposited by sol gel technique on glass substrates using different precursors (zinc acetate, zinc nitrate and zinc chloride). In the present work we investigate the precursor nature influence on structural, morphological, optical, electrical properties and photocatalytic activity of ZnO thin films. For this purpose we have used X-rays diffraction (XRD), atomic force microscopy (AFM), UV–visible spectroscopy and Hall effect measurements for films characterization. The obtained results indicated that ZnO films properties are strongly influenced by the nature of the used precursor as reactant. Films photocatalytic activity was evaluated by the photo-degradation of methylene blue (MB) dissolved in aqueous solution under UV-A light. The obtained results indicated that ZnO thin films prepared from zinc acetate are more efficient than those prepared from zinc nitrate and zinc chloride.