Multiwalled Nanotubes: Their Formation by Irradiating Graphite with High Doses of Electrons

We report the production of carbon nanotubes by high dose of electron irradiation. The irradiation was performed with a 2 MeV Van de Graaff accelerator, while the irradiation conditions were the following: voltage 1.3 MeV, current 5 µA, dose rate 25 kGy/min, and total dosage 1000 kGy. The samples were analyzed in a high-resolution transmission electron microscope. The main features observed on the samples, were huge nanotubes of several nanometer long and few nanometer wide, which are capped at one end. It is good to point out, that at this level of irradiation, we were not able to find either onion-like or particle structures throughout the material, as it is usual in similar hexagonal structures. This behavior could be attributed to the level of irradiation used to create the nanotubes under investigation.     

Electrochemical determination of rusted steel surface stability

The stability of a rusted steel surface exposed to a 0.11 M sodium sulphate solution has been studied. Electrochemical impedance spectroscopy, polarization resistance and atomic absorption analysis techniques were used in conjunction with mild steel specimens rusted in a rural atmosphere and treated with different concentrations of phosphoric acid. Since most of the impedance diagrams obtained differ from the typical semicircle, it is not clear how to obtain kinetic information on the corrosion process. The polarization resistance technique gives more useful data.     

Deformation and failure mechanism of nano-composite coatings under nano-indentation

Two nano-composite coatings based on nc-TiC particles in an a-C:H matrix are deposited via closed-field unbalanced reactive magnetron sputtering. The compositions of the coatings are varied by changing the acetylene gas flow during the depositions. A Cr/Cr–Ti/Ti–TiC graded interlayer is introduced between substrate and coating. Electron probe micro-analyses (EPMA) show that the Ti content of the coatings varies between 31.7 and 11.5 at.%. The coatings exhibit a hardness (H) of 20.0 and 15.7 GPa, and a Young's modulus (E) of 229.4 and 136.6 GPa, respectively, as measured through nano-indentations. Cube corner indentations are performed to probe the fracture toughness of the coatings through the determination of critical indentation loads (L_r) at which radial cracks start to propagate. Transmission electron microscopy (TEM) observations and energy-filtered TEM are employed to characterize the coatings nanostructures. The variation in Ti content is accompanied by a variation in TiC particle size and volumetric fraction, as well as a change in the columnar structure of the coatings. A focus ion beam (FIB) slicing technique is employed to prepare samples from nano-indented locations of coated Silicon and stainless steel (SS) substrates. TEM inspection of the FIB sliced samples determines that the most brittle phase in the coating is the C-enriched columnar boundary, and identifies the location of failure within the interlayer. As a consequence of the different nanostructure, the coatings exhibit different elastic recovery properties and toughness.     

Microstructure and properties of TiB/Ti-6Al-4V coatings produced with laser treatments

TiB/Ti-6Al-4V metal-matrix composite (MMC) layers were produced on Ti-6Al-4V substrates by laser cladding. A TiB₂/Ti powder mixture was used as a precursor to obtain a dispersion of TiB needles in the Ti alloy matrix, with the aid of an exothermic reaction between TiB₂ and Ti. A eutectic microstructure was obtained that consisted of an extremely homogeneous dispersion of TiB eutectic needles in the Ti alloy matrix, having a volume fraction as high as 0.33. Also, an equilibrium-like microstructure was found, consisting of a dispersion of both primary and eutectic TiB needles inside the Ti alloy matrix. An analysis of the geometry of the layers was performed and proved successful in determining the percentage of B. Further, it correctly predicted the variation of atomic B content as a function of laser power. The relative wear resistance coefficient, defined as the wear coefficient of the uncoated matrix divided by that of coating, shows an improvement by a factor as high as 1500 for the eutectic microstructure. This paper was presented at the 2nd International Surface Engineering Congress sponsored by ASM International, on September 15–17, 2003, in Indianapolis, Indiana, and appeared on pp. 411–18 of the Proceedings.     

Three-dimensional space-vector modulation algorithm for four-leg multilevel converters using abc coordinates

In this paper, a novel three-dimensional (3-D) space-vector algorithm for four-leg multilevel converters is presented. It can be applied to active power filters or neutral-current compensator applications for mitigating harmonics and zero-sequence components using abc coordinates (referred from now on this paper as natural coordinates). This technique greatly simplifies the selection of the 3-D region where a given voltage vector is supposed to be found. Compared to a three-level modulation algorithm for three-leg multilevel converters, this algorithm does not increase its complexity and the calculations of the active vectors with the corresponding switching time that generate the reference voltage vector. In addition, the low-computational cost of the proposed algorithm is always the same and it is independent of the number of levels of the converter.     

Experimental Design Applied for Cost and Efficiency of Antioxidants in Biodiesel

Oxidation stability is a parameter of great importance for biodiesel quality control to both producers and subsequent consumers. To maintain the quality of biodiesel, currently the most effective and economical method is the addition of antioxidants that prevent or retard the biofuel oxidation reaction. In this study, efficiency and cost of synthetic antioxidants added to B100 biodiesel from soybean oil and pork fat were evaluated, using butylhydroxyanisole (BHA), butylhydroxytoluene (BHT) and tert-butylhydroquinone (TBHQ), in pure form or in mixtures, according to a simplex-centroid mixture experimental design. Results demonstrate an increased induction period (IP) in all trials when compared to the control sample, and TBHQ was the only antioxidant alone that met all the specification standards, while BHT and BHA alone met only the American standard specifications. The antioxidant mixture that presented the highest synergistic effect was that of TBHQ and BHA. Multi-response optimization indicated an optimum formulation containing 75 % TBHQ and 25 % BHA with an IP of 7.27 h at 110 °C and the antioxidant mixture cost of 31.31 USD, to be added for a ton of biodiesel. This simplex-centroid mixture experimental design shows an ability to be applied in the biodiesel, oils and fats industry to evaluate the oxidation stability and the occurrence of synergism between different mixtures of synthetic or natural antioxidants and their costs.