Electrospun microporous gelatin–polycaprolactone blend tubular scaffold as a potential vascular biomaterial

The work reported involved the fabrication of an electrospun tubular conduit of a gelatin and polycaprolactone (PCL) blend as an adventitia‐equivalent construct. Gelatin was included as the matrix for increased biocompatibility with the addition of PCL for durability. This is contrary to most of the literature available for biomaterials based on blends of gelatin and PCL where PCL is the major matrix. The work includes the assiduous selection of key electrospinning parameters to obtain smooth bead‐free fibres with a narrow distribution of pore size and fibre diameter. Few reports elucidate the optimization of all electrospinning parameters to fabricate tubular conduits with a focus on obtaining homogeneous pores and fibres. This stepwise investigation would be unique for the fabrication of gelatin–PCL electrospun tubular constructs. The fabricated microfibrous gelatin–PCL constructs had pores of size ca 50–100 μm reportedly conducive for cell infiltration. The measured value of surface roughness of 57.99 ± 17.4 nm is reported to be favourable for protein adhesion and cell adhesion. The elastic modulus was observed to be similar to that of the tunica adventitia of the native artery. Preliminary in vitro and in vivo biocompatibility tests suggest safe applicability as a biomaterial. Minimal cytotoxicity was observed using MTT assay. Subcutaneous implantation of the scaffold demonstrated acute inflammation which decreased by day 15. The findings of this study could enable the fabrication of smooth bead‐free microfibrous gelatin–PCL tubular construct as viable biomaterial which can be included in a bilayer or a trilayer scaffold for vascular tissue engineering. © 2019 Society of Chemical Industry     

Sintering studies of nano-crystalline zinc oxide

Sintering and grain growth of nano-crystalline undoped ZnO has been studied in detail over a wide range of temperature and holding time. Below 800 °C, sintering of over 70% theoretical density is not observed, irrespective of particle size. At 900 °C for 6 h, the nano-crystalline sample sinters to 99% of theoretical density whereas the density for as received sample is 93% of theoretical density. However, at 1300 °C or higher, the densification is found to be much faster and after a few hours becomes independent of holding time. Grain growth studies reveal a similar feature of attaining saturation over holding time. The average saturated grain size is found to be ∼1.5 and ∼2.2 μm at 800 and 900 °C, respectively, while at 1300 °C or higher, it is in between 12 and 13 μm.     

The Einstein relation in nanostructured materials: simplified theory and suggestion for experimental determination

An attempt is made to study the Einstein relation for the diffusivity–mobility ratio (DMR) in quantum wells (QWs) and quantum well wires (QWWs) of tetragonal compounds on the basis of a newly formulated electron energy spectrum taking into account the combined influences of the anisotropies in effective electron mass, the spin–orbit splitting, and the presence of crystal field splitting, respectively. The results for quantum-confined III–V compounds form a special case of our generalized analysis. The DMR has also been studied for QWs and QWWs of II–VI and IV–VI materials. Taking QWs and QWWs of CdGeAs₂, InAs, CdS and PbSe as examples, it was found that the DMR increases with increasing carrier statistics and decreasing film thickness respectively in various oscillatory manners emphasizing the influence of dimensional quantizations and the energy band constants in different cases. An experimental method of determining the DMR in nanostructures with arbitrary dispersion laws has also been suggested and the present simplified analysis is in agreement with the suggested relationship. The well-known results for nanostructures with parabolic energy bands have also been obtained as special cases from this generalized analysis under certain limiting conditions.     

Fatty acids from Macoma sp. of bivalve mollusc

Fatty acids of the total lipids of flesh and hepatopancreas of Macoma sp. have been determined. The level of 20:5w3 (ca 17%), a biologically important fatty acid, was found to be considerably high. Other major component fatty acids were 16:0, 16:1, 18:1 and 22:4w6. High levels of 22:5w6 (8%), 22:5w3 (8%) and 22:6w3 (ca 15%) were found in flesh lipid. Nonsaponifiables were also high (28–30%). Alkyl ether acyl glycerols were found in flesh (1.3%) and hepatopancreas (3.8%).     

Cisapride reduces neonatal postoperative ileus: randomised placebo controlled trial

AIM: To assess the efficacy of cisapride in reducing ileus persisting to the tenth postoperative day after neonatal abdominal surgery. METHODS: A prospective, randomised, double blind trial comparing rectal cisapride (1.4-2.3 mg/kg/day) with placebo over seven days was undertaken in 33 neonates. RESULTS: Seven of 12 (58%) patients receiving placebo and eight of 11 (73%) receiving cisapride achieved a first sustained feed during treatment. Of those receiving cisapride, the first sustained feed occurred at 2.3 days (SEM 0.6) compared with 4.7 days (SEM 0.8) with placebo. By the seventh day the mean daily net enteral balance was 69 (SEM 18) ml/kg in the cisapride subgroup and 17 (SEM 8) ml/kg for those receiving placebo. Stool was passed on 6.3 (SEM 0.4) treatment days in the cisapride subgroup compared with 4.1 (SEM 1.0) treatment days in the placebo subgroup. CONCLUSION: Cisapride is effective in neonates with a prolonged ileus after abdominal surgery.     

Comparative hall measurements on wet- and dry-oxidized 4H-SiC MOSFETs

Hall measurements have been used to compare the properties of 4H-SiC inversion-mode MOSFETs with “wet” and “dry” gate oxides. While the field-effect mobilities were approximately 3–5 cm²/Vs, the Hall mobilities in 4H-SiC MOSFETs in the wet and dry oxide samples were approximately 70–80 cm²/Vs. The dry-oxidized metal oxide semiconductor field effect transistors (MOSFETs) had a higher transconductance, improved threshold voltage, improved subthreshold slope, and a higher inversion carrier concentration compared to the wet-oxidized MOSFETs. The difference in characteristics between the wet- and the dry-oxidized MOSFETs is attributed to the larger fixed oxide charge in the dry oxide sample and a higher interface trap density in the wet oxide sample.     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Network and device-level impacts: performance and reliability of active I/O storage systems

Distributed active storage architectures are designed to offload user-level processing to the peripheral from the host servers. In this paper, we report preliminary investigation on performance and fault recovery designs, as impacted by emerging storage interconnect protocols and state-of-the-art storage devices. Empirical results obtained using validated device-level and interconnect data demonstrate the significance of the said parameters on the overall system performance and reliability.     

Microarchitectures for Managing Chip Revenues under Process Variations

As transistor feature sizes continue to shrink intothe sub-90nm range and beyond, the effects of process variationson critical path delay and chip yields have amplified. A commonconcept to remedy the effects of variation is speed-binning, bywhich chips from a single batch are rated by a discrete range offrequencies and sold at different prices. In this paper, we discussstrategies to modify the number of chips in different bins andhence enhance the profits obtained from them. Particularly, wepropose a scheme that introduces a small Substitute Cacheassociated with each cache way to replicate the data elementsthat will be stored in the high latency lines. Assuming a fixedpricing model, this method increases the revenue by as much as13.8% without any impact on the performance of the chips.     

A unique method for reducing losses of bends in dielectric optical wave guide

The dielectric optical wave guide is finding growing attention at millimeter wave frequencies. However the dielectric optical waveguide radiates at bends and thus transmission loss increases. These radiations are in the outword direction of bends. This output radiation at output bends arises due to change in phase velocities of the propagating wave at the centre of the dielectric guide and the phase velocity at the outer surface of the dielectric guide. A unique methiod is suggested to avoid these radiation losses.Experimental results are also shown at microwave frequencies.