Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

CFD Prediction of Flow and Homogenization in a Stirred Vessel: Part I Vessel with One and Two Impellers

A simulation of flow field and tracer homogenization was performed using the commercial CFD software FLUENT 6.1. The aim is to investigate the potential of CFD software to predict concentration distribution of added tracer in cylindrical vessels. The calculated results – dimensionless velocity profiles, power and pumping numbers, dimensionless concentration curves, and mixing times – were compared with experiments in stirred vessels. In Part I, the study was performed for vessels agitated by one or two impellers on a centric shaft. Two different impellers were used – a 6‐bladed 45° pitched blade turbine and a standard Rushton turbine. The standard k‐? turbulence model and multiple reference frames method were used for the simulations. The influence of the grid type was also investigated; three types of grid – a structured, unstructured and a special user‐defined grid – were studied.     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Regional chemotherapy of liver tumors

In the absence of adequate autogenous vein for tibial artery bypass in limb salvage surgery, the use of prosthetic grafts with a distal anastomotic vein cuff or patch has shown promising results. Here, we describe how the Florester Internal Vessel Occluder (Meadox UK, Bedfordshire, UK) can facilitate the construction of a distal anastomotic vein cuff.     

A VERSATILE CORRELATION OF LIQUID HOLD-UP IN TWO-PHASE COUNTER-CURRENT TRICKLE BED COLUMN

A new definition of the flooding point in a two-phase counter-current trickle bed column has been proposed. Based on this point a versatile correlation of liquid hold-up has been formulated. The coefficients of this correlation are invariant to the change of physical properties of liquid, type and size of the packing forming the bed and gas velocity. This conclusion has been reached from the analysis of experiments with four different liquids irrigating the bed and three types of packing of various size. The versatile correlation can be used also re-currently to calculate flooding hold-up and flooding liquid rate from two known values of liquid hold-up for a given gas rate.     

Two Isomers of C60F48: Computed Inter-isomeric Equilibrium

C₆₀F₄₈ has been known to exist in two isomeric forms of D₃ and S₆ symmetries. However, the quantum-chemical calculations have not agreed on their stability order though a near-isoenergetic picture is otherwise always encountered. In order to clarify the situation, the entropy effects are evaluated for synthetic temperatures of about 500K. The entropy evaluations suggest that the D₃ isomer should be more stable in the potential energy by 2.05-2.55 kcal/mol (to which term the ab initio data are closer than the semiempirical ones).     

Minimal inhibition concentrations of selected antibiotics for strains of Staphylococcus aureus

Minimal inhibition concentrations (MIC) of gentamycin (Ge), neomycin (Neo), rifampicin (Rif), ampicillin (Amp), lincomycin (Lin), erythromycin (Ery), and streptomycin (STM) were determined by the agar dilution technique using 46, 130, 131, 125, 140, 139 and 142 strains of Staphylococcus aureus, respectively. The strains, selected from the collection of the authors' laboratory, were isolated from mammary gland secretions of cows affected with clinical or subclinical mastitis. The following ranges of MIC (micrograms/ml) were assessed for the antibiotics under study: Ge 0.125-0.50, Neo 0.06-0.50, Rif 0.0039-0.030, Amp 0.015-1.00, Lin 0.25-1.00, Ery 0.06-0.25, STM 0.50-64.0. Modal MIC (micrograms/ml) were as follows; Ery 0.125 (86%), Lin 0.5 (71.4%), Rif 0.007 (68.7%), Ge 0.25 (56.5%), STM 1.00 (54.2%), Neo 0.25 (53.8%), Amp 0.06 (41.6%). The order of efficiency expressed in MIC 90 (micrograms/ml) was as follows: Rif (0.015), Ery (0.125), Ge (0.25), Neo (0.25), Amp (0.5), STM (4.0).     

Detection and identification of mycobacteria in formalin-fixed, paraffin-embedded tissues by nested PCR and restriction enzyme analysis

A novel assay based on a nested PCR and restriction enzyme analysis of the PCR products was developed for the rapid detection and identification of Mycobacterium bovis and M. avium-M. intracellulare species in formalin-fixed, paraffin-embedded tissue (PET) specimens. On the basis of the nucleotide sequence data obtained in the present study, general nested primers were constructed to amplify a 424-bp segment of the gene encoding the 65-kDa surface antigen of mycobacteria. The nested PCR assay proved to be highly sensitive, since as little as 5 to 10 fg of extracted mycobacterial DNA was detected. The safety of the assay as a routine method for the diagnosis of M. bovis and M. avium-M. intracellulare in PET specimens was provided by taking various precautions. In order to prevent false positivity, specific tools and procedures were applied. To detect false-negative results and assess the efficiency of the PCR, an internal standard molecule of amplification was constructed. The digestion of the amplicons with the restriction endonuclease Sau96-I allowed the identification of M. bovis and M. avium-M. intracellulare in a large number of clinical specimens. The present results indicate that PCR combined with an internal control of amplification and restriction enzyme analysis of the amplicons provides a rapid, sensitive, and reliable method for routine diagnostic laboratories to detect and identify M. bovis and M. avium-M. intracellulare in PET specimens.