Evidence for the Microwave Effect During the Annealing of Zinc Oxide

A microwave/conventional hybrid furnace has been used to anneal virtually fully dense zinc oxide ceramics under pure conventional and a microwave/conventional hybrid heating regime with a view to obtaining evidence for the "microwave effect" during the resulting grain growth. In each case it was ensured that each sample within a series had an identical thermal history in terms of its temperature/time profile. The results showed that grain growth was enhanced during hybrid heating compared with pure conventional heating; the greatest enhancement, a factor of ∼3 increase in average grain size, was observed in the range 1100°–1150°C. The grain growth exponent decreased from 3 during conventional heating to 1.4 during hybrid heating in this temperature range, suggesting an acceleration of the diffusional processes involved. Temperature gradients within the samples were found to be too small to explain the results. This suggests that clear evidence has been found to support the existence of a genuine "microwave effect."     

Processing of hydroxyapatite ceramic foams

A novel method of producing highly porous hydroxyapatite ceramics via the foaming of ceramic slips is discussed. Foams with densities 15% and an open cell structure have been produced.     

Mechanical properties and grain orientation evolution of zirconium diboride-zirconium carbide ceramics

The effect of ZrC on the mechanical response of ZrB₂ ceramics has been evaluated from room temperature to 2000 °C. Zirconium diboride ceramics containing 10 vol% ZrC had higher strengths at all temperatures compared to previous reports for nominally pure ZrB₂. The addition of ZrC also increased fracture toughness from $～3\text{.5}\text{MPa}\sqrt{\text{m}}$ for nominally pure ZrB₂ to $～4\text{.3}\text{MPa}\sqrt{\text{m}}$ due to residual thermal stresses. The toughness was comparable with ZrB₂ up to 1600 °C, but increased to $4\text{.6}\text{MPa}\sqrt{\text{m}}$ at 1800 °C and 2000 °C. The increased toughness above 1600 °C was attributed to plasticity in the ZrC at elevated temperatures. Electron back-scattered diffraction analysis showed strong orientation of the ZrC grains along the [001] direction in the tensile region of specimens tested at 2000 °C, a phenomenon that has not been observed previously for fast fracture (crosshead displacement rate = 4.0 mm min^?1) in four point bending. It is believed that microstructural changes and plasticity at elevated temperature were the mechanisms behind the ultrafast reorientation of ZrC.     

Primary hemangiosarcoma of the heart

A 50-year-old woman ASA 2 underwent carbon dioxide hysteroscopy under general anaesthesia. Monitoring showed a sudden and rapid fall in end-tidal carbon dioxide followed by oxygen desaturation. She became pulseless and cyanosed. Resuscitation with oxygen, intravenous adrenaline and head-down tilt restored her to haemodynamic stability. Hyperbaric therapy was also administered as air embolism could not be excluded.     

Readmission discount factors in program evaluation. An output value analysis of an adult psychiatry program

The application of output value analysis, a type of benefit/cost analysis, to a psychiatric patient population is reported. A method for discounting the value of the program if a patient was readmitted within a year after discharge was introduced. The application of this discount factor reduces the value produced by the program and thereby reduces both productivity and effectiveness indices. When applied to groups known to differ in readmission rates, such as first admissions and readmissions or voluntary and involuntary admissions, the discount factor can accentuate group differences markedly. When selected diagnostic groups were compared, the discount factor could even reverse the relative standing of the groups.     

Microwave Initiated Self-Propagating High-Temperature Synthesis of SiC

The use of microwave energy to initiate self-propagating, high-temperature synthesis (SHS) of Si + graphite mixtures has been investigated. The results indicate that, unlike with conventional ignition techniques, green densities in excess of 80% of theoretical can be ignited and the combustion wavefront can be crudely controlled. It was found that the induction time for ignition increased with increasing green density and that a higher microwave power level was required with the denser green pellets to achieve the same ignition time. Combustion front velocity increased with green density. The degree of densification was found to decrease with increasing green density. For a given green density, the degree of densification increased with increasing microwave power. The product contained a significant proportion of ultrafine (36–72 nm diameter) SiC whiskers; despite this, final densities as high as 83.6% of theoretical could be obtained without the use of applied pressure. This compares with the 50% densities obtained via conventional ignition techniques.     

UHTC–carbon fibre composites: Preparation,oxyacetylene torch testing and characterisation

Current generation carbon–carbon (C–C) and carbon–silicon carbide (C–SiC) materials are limited to service temperatures below 1800 °C and materials are sought that can withstand higher temperatures and ablative conditions for aerospace applications. One potential materials solution is carbon fibre-based composites with matrices composed of one or more ultra-high temperature ceramics (UHTCs); the latter are intended to protect the carbon fibres at high temperatures whilst the former provides increased toughness and thermal shock resistance to the system as a whole. Carbon fibre–UHTC powder composites have been prepared via a slurry impregnation and pyrolysis route. Five different UHTC compositions have been used for impregnation, viz. ZrB₂, ZrB₂–20 vol% SiC, ZrB₂–20 vol% SiC–10 vol% LaB₆, HfB₂ and HfC. Their high-temperature oxidation resistance has been studied using a purpose built oxyacetylene torch test facility at temperatures above 2500 °C and the results are compared with that of a C–C benchmark composite.     

Price dynamics in European petroleum markets

This paper analyses horizontal and vertical price dynamics in the EU petroleum markets. The results indicate that the cross-country price differentials have significant impact on the local price adjustments. We investigate the cross-national price spill-overs and find that the extent of the welfare transfer due to asymmetric price transmission, when analysed in a cross-country setting, is less pronounced than claimed in previous contributions in this area. We also find empirical evidence, although indirect, for the politically charged concept of “fuel tourism”, using a pan-European cross-product time series dataset.     

Evidence for the Microwave Effect During Hybrid Sintering

A microwave/conventional hybrid furnace has been used to sinter three ceramics with different microwave absorption characteristics under pure conventional and a range of microwave/conventional hybrid heating regimes. The precursor powder particle size was also varied for each material. In each case it was ensured that every sample within a series had an identical thermal history in terms of its temperature/time profile. An increase in both the onset of densification and the final density achieved was observed with an increasing fraction of microwave energy used during sintering, the effect being greatest for the materials that absorbed microwaves most readily. Twenty-three percent greater densification was observed for submicron zinc oxide powder, the material with the largest microwave absorption capability, when sintered using hybrid heating involving 1 kW of microwave power compared with pure conventional power under otherwise identical conditions. For the ceramic with the lowest microwave absorption characteristic, alumina, the increase in densification was extremely small; partially stabilized zirconia, a moderate microwave absorber, was intermediate between the two. Temperature gradients within the samples, a potential cause of the effect, were assessed using two different approaches and found to be too small to explain the results. Hence, it is believed that clear evidence has been found to support the existence of a genuine "microwave effect."