Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...     

铝合金ADC12Z高压铸造过程中铸件与铸型间界面热交换系数的研究

通过采集高压铸造过程中铸型内部温度的变化曲线,采用热传导反算法,求解了以铝合金ADC12Z为铸件材料的铸件-铸型界面换热系数,分析了该界面换热系数随铸件厚度的变化规律.计算及分析结果表明:在压铸过程中,铸件-铸型界面换热系数迅速升至最大值,随后下降,凝固结束后趋于稳定.铸件厚度增大不仅提高了换热系数,而且对换热系数的变化趋势也有很大影响.同时,不同厚度的铸件,其固相率和冷却速率的变化规律也有较大区别.     

Expansion microscopy

Super‐resolution optical microscopy techniques have revolutionized how we see and understand biology. In recent past, a new super‐resolution optical microscopy technique called expansion microscopy (ExM) was developed. Unlike other pre‐existing super‐resolution imaging techniques, this technique achieves super‐resolution by physically expanding biological specimens via a swellable hydrogel. After the development of ExM, various techniques based on ExM but with improved performance in various aspects, have been developed. In this review, we introduce the basic principles of ExM and its variants. and compare the advantages and disadvantages of these techniques. In addition, we present the applications of ExM techniques in various fields.     

Silicone-coated polyimide films deposited by surface dielectric barrier discharges

Hybrid dielectric barrier discharges are investigated for plasma generated on the surface of a dielectric layer, where two conducting electrodes of high voltage and ground are formulated on the upper and bottom surfaces. Using a flexible thin polyimide-film of a thickness ranging from 25 to 125 μm, a plasma is generated with a voltage of about 1 kV and a frequency of 40 kHz.However, the surface of the dielectric layer was etched through a chemical reaction involving plasma oxygen radical species, and thus the polyimide films failed readily, resulting in dielectric breakdown within short operating time ranging from a few minutes to several tens of minutes,based on the film thicknesses of 25 μm and 125 μm, respectively. These plasma erosions were prevented by coating the polyimide surface with a 25 μm thick silicone paste. The siliconecoated film surface was then reinforced remarkably against plasma erosion as the organic polymer was vulnerable to chemical reaction of the plasma species, while the inorganic silicone exhibited a high chemical resistance against plasma erosion.     

SSI体系阻尼比实测及其分布规律研究

 阻尼比是结构动力分析的重要动力特性参数,目前规范采用的阻尼比是基于刚性地基或近似刚性地基的试验结果,未能考虑土与结构相互作用(SSI)效应。针对SSI效应问题,体系阻尼比的准确评估是其动力分析的重要前提。为了实现实际SSI体系阻尼比值较准确的识别,提出环境激励下SSI体系阻尼比测试与识别方法,并应用这一识别方法,给出西安及其周围地区82幢各类SSI体系基本等效黏滞阻尼比的实测识别结果。同时在实测阻尼比数据的基础上,初步研究实际SSI体系阻尼比的总体分布规律、影响因素和取值范围。     

Effects of honing treatment on AIP-TiN and TiAlN coated end-mill for high speed machining

The objective of this work is to compare the tool performance of TiN and TiAlN coated carbides end-mills deposited by an arc ion plating (AIP) method, using honing treatment to polish the cutting edge surface sleekly. The curve of surface roughness versus honing time showed a rapid improvement initially and thereafter became steady, manifesting a saturation effect. The optimal honing time related to surface roughness was determined to be approximately 20 s. As the surface roughness increased, the critical loads reduced. At an average surface roughness (Ra) of 0.028 μm, the highest critical loads of TiN and TiAlN coating layers were 98 and 114 N, respectively. Tool performances of uncoated and coated tools were conducted under high speed machining (HSM) of AISI D2 cold-worked die steel (62 HRC). Consequently, the TiAlN coated end-mill using honing treatment showed excellent tool life under HSM conditions.     

铝合金压铸过程铸件/铸型界面换热行为的研究Ⅱ.工艺参数对界面换热的影响

基于本文第1部分的数学模型,求解了各种工艺参数下铸件/铸型间的界面热流和换热系数,重点研究不同工艺参数对于界面热流和换热系数的影响.在现有的"阶梯"块铸件的条件下,计算结果表明:压铸过程各种工艺参数对于铸件/铸型界面热流和换热系数有着不同的影响规律.铸型初始模腔表面温度对于界面热流的峰值有着很大的影响,随着铸型初始模腔表面温度的上升,热流峰值不断下降.对于较厚的"阶梯"面,铸型初始模腔表面温度对于界面换热系数的影响较大,随着该温度的上升,界面换热系数的峰值不断下降;对于较薄的"阶梯"面,各种工艺参数对于界面换热系数的影响不大.     

Optical diffraction gratings embedded in BK-7 glass by low-density plasma formation using femtosecond laser

The optical embedded diffraction gratings with the internal refractive index modification in BK-7 glass plates were demonstrated using low-density plasma formation excited by a high-intensity femtosecond (130 fs) Ti: sapphire laser (λp=790 nm). The refractive index modifications with diameters ranging from 400 nm to 4 μm were photoinduced after plasma formation occurred upon irradiation with peak intensities of more than 1×1013 W/cm2. The graded refractive index profile was fabricated to be a symmetric around the center of the point at which low-density plasma occurred. The maximum refractive index change (Δn) was estimated to be 1.5×10-2. Several optical embedded gratings in BK-7 glass plate were demonstrated with refractive index modification induced by the scanning of low-density plasma formation.     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.