Heat propagation in thermally conductive polymers of PA6 and hexagonal boron nitride

Thermally conductive polymers offer new possibilities for the heat dissipation in electric and electronic components, for example, by a three‐dimensional shaping of the heat sinks. To face safety regulations, improved fire performance of those components is required. In contrast to unfilled polymers, those materials exhibit an entirely different thermal behavior. To investigate the flammability, a phosphorus flame retardant was incorporated into thermally conductive composites of polyamide 6 and hexagonal boron nitride. The flame retardant decreased the thermal conductivity only slightly. However, the burning behavior changed significantly, due to a different heat propagation, which was investigated using a thermographic camera. An optimum content of hexagonal boron nitride for a sufficient thermal conductivity and fire performance was found between 20 and 30 vol%. The improvement of the fire performance was due to a faster heat release out of the pyrolysis zone and an earlier decomposition of the flame retardant. For higher contents of hexagonal boron nitride, the heat was spread faster within the part, promoting an earlier ignition and increasing the decomposition rate of the flame retardant.     

Light-induced electron spin polarization in the ground state of water-soluble copper porphyrins

Light-induced spin-polarized transient EPR spectra are reported for several water-soluble copper porphyrins. The spectra are assigned to the doublet ground state, with emissive spin polarization resulting from photoexcitation and subsequent electronic relaxation. In contrast to other systems for which polarization of a doublet ground state has been observed, the exchange interactions in the copper porphyrins are strong and the geometry is fixed. It is proposed that intersystem crossing from the photoexcited trip-doublet to the trip-quartet state can lead to net polarization of the spin system and that this polarization is maintained during electronic decay, possibly via charge-transfer and exciplex states. The intensity of the observed spin polarization is essentially independent of the molecular orientation in the external field, but is strongly dependent on the nature of the charged peripheral groups. Possible reasons for this behavior are discussed.     

Triggering of cellulase biosynthesis by cellulose in Trichoderma reesei. Involvement of a constitutive, sophorose-inducible, glucose-inhibited beta-diglucoside permease

We prepared [U-14C]cellobiose by cultivating Acetobacter pasteurianus in the presence of [U-14C]glucose and hydrolyzing the [U-14C]cellulose formed with beta-glucosidase-free cellulase from Trichoderma reesei. This 14C-labeled cellobiose was used to investigate the presence of an uptake system for cellobiose in T. reesei. Evidence was obtained for the presence of a high affinity (Km for cellobiose 0.3 microM) but low activity (2.5 milliunits/mg fungal dry weight) cellobiose permease. The permease is formed constitutively, but higher levels are formed after addition of sophorose (glucosyl-beta-1,2-diglucoside), a reputed cellulase inducer. The permease appears to be specific for beta-diglucosides, as the uptake of [U-14C]cellobiose is inhibited by sophorose, gentiobiose (glucosyl-beta-1,3-glucoside), and cellobiose. Under these conditions, cellooligodextrines (n, 4-7; final concentration, 1 mM) are not inhibitors. Glucose, but no other monosaccharides, inhibits the permease. The hypersecretory mutant T. reesei RUT C-30 exhibits elevated permease activities, whereas in T. reesei QM 9979, a mutant strain defective in the induction of cellulases by cellulose or sophorose, strongly reduced permease activities were demonstrated. The results stress a hitherto not recognized point of control in the induction of cellulases by T. reesei at the level of uptake of cellulose oligosaccharides.     

Zur Fließfähigkeit von Schüttgütern – Definition und Meßverfahren

Flowability of Bulk Solids – Definition and Measuring Principles . The flowability of bulk solids has to be known for many practical applications. The present paper describes how the flowability is defined and on which physical properties it depends. Experimental determination of the flowability using a shear test is demonstrated. Conditions influencing measuremed results are described. Finally an overview of various methods used for characterization of the flowability of bulk solids is given.     

Cortisone-induced osteoporosis: effects on bone adenylate cyclase

The majority of patients with soft tissue or bone sarcomas of the upper extremity can be treated today with limb-saving procedures using combined modality therapies. For patients with a tumor in the shoulder area, sometimes an interscapulothoracic amputation is the only radical surgical treatment. However, in selected cases, in which the tumor does not involve the neurovascular bundle, a limb-sparing alternative might be the Tikhoff-Linberg resection. Normal function of the hand and forearm, with reasonable function of the elbow, can be maintained by this procedure. Four case histories are reported.     

Vital-Fluorochromization of Microorganisms Using 3′,6′-Diacetylfluorescein to Determine Damages of Cell Membranes and Loss of Metabolic Activity by Ozonation

Cell suspensions of Escherichia coli as a model for bacterial populations in wastewaters were treated with ozone as a disinfectant in a continuously operated pilot plant with a plug flow reactor. Suspensions with an initial number of CFU (colony forming units) of 10⁸ mL^?1 were ozonized with ozone concentrations up to 12 mg/L. Metabolic activities and membrane functions break down with increasing ozone concentrations. The fluorochromization using 3′,6′-diacetylfluorescein (FDA) proved to be a suitable method for the detection of an alteration in permeability of the cell membranes and an inactivation of metabolic activity. By fluorescence microscopic and photometric investigations it could be clearly demonstrated that, in the case of disinfection with ozone, inactivation of the cells includes first of all a damage of the cell membranes. In contrast to the determination of the number of CFU, fluorochromization allows the detection of alteration in metabolic activities.     

Large specimen bone embedment and cement line staining

Undecalcified embedment of large bone specimens is often challenging. A method is presented here that is suitable for methacrylate embedment of sections of canine vertebrae while retaining the ability to localize tartrate-resistant acid phosphatase and alkaline phosphatase activity. Specimens also retained tetracycline labelling, and sectioned preparations were readily stained with routine bone procedures. A modification of the Bodian silver stain, used for examining the nerves and spinal cord in these specimens, provided a useful stain for canaliculi and cement lines in trabecular and cortical bone. This stain is advantageous when both bone and nerve tissue are of interest, as in spinal fusion studies.     

High quality LTCC resonator for voltage-controlled oscillator

Design and technology of microwave conductor lines embedded in low-temperature cofired ceramic (LTCC) multilayer substrates are summarized with a focus on achieving the highest possible quality (Q) factor for a given line inductance. The work was initiated to test the integrability of base station voltage-controlled oscillators (VCOs) in ceramic multilayer substrates. This approach leads to a miniaturization of current versions by a factor of 2 to 4. However, base station specifications for phase noise and hence resonator Q are extremely demanding. Therefore, both the design and the processing technology were optimized. By choosing a twin-line design with two parallel lines vertically separated by a single LTCC layer, Q factors of 90 and 180 have been achieved for integrated 5.5 nH inductors at frequencies of 640 MHz and 1650 MHz, respectively. Application of this result to VCO modules in standard LTCC technology already yields low phase noise levels, e.g., -136 dBc/Hz at 100 kHz offset, which is suitable for base station applications. However, further noise reduction is expected from a dedicated high Q fabrication process that uses conventional via punching and filling steps to replace the ceramic material between the two lines by conductive silver paste. This raises the Q to 120 and 200, respectively, at the two frequencies and adds extra degrees of freedom to LTCC design for low-loss wireless solutions.