Cavitation Damage of the single-crystal nickel-base superalloy SRR99 during creep at 850°C

Various heat treatments of the single-crystal nickel-base superalloy SRR99 have been carried out to produce a wide range of initial γ′ phase morphology. The cavitation damage has been studied after creep fracture at 850°C and stresses between 400MPa and 650 Mpa. The crep fracture surfaces and longitudinal sections of crept specimens have been examined by image analysing system in order to determine the size distribution and the area fraction of (001)-planes cracks on fracture surface characterise the creep crack damage level. The cracking morphology in fractured material as a function of stress and γ′-phase size has also been investigated. The results show, that crack propagation occurred anisotropically on (001) crystallographic planes perpendicular to the aplied stress along the γ/γ′ interfaces. It was found, that creep cracks dependent on the shape and size of γ′-phases developing at the temperature and stress level.     

On the Electromagnetic Interference Fringes Method in Geophysical Prospecting Applications

The method of electromagnetic interference fringes for the prospecting of conductive subsurfaces inside the earth is reviewed. The fields radiated by an electrically small horizontal loop situated on the earth's surface are derived and expressed in terms of different interfering wave components. The variable distance interference fringes (VDIF) method and the variable frequency interference (VFIF) method of prospecting are considered, and an interpretation procedure using the data obtained from both methods is suggested.     

Improvement of the cell performance in the ZnS/Cu(In,Ga)Se2 solar cells by the sputter deposition of a bilayer ZnO : Al film

ZnS is a candidate to replace CdS as the buffer layer in Cu(In,Ga)Se₂ (CIGS) solar cells for Cd‐free commercial product. However, the resistance of ZnS is too large, and the photoconductivity is too small. Therefore, the thickness of the ZnS should be as thin as possible. However, a CIGS solar cell with a very thin ZnS buffer layer is vulnerable to the sputtering power of the ZnO : Al window layer deposition because of plasma damage. To improve the efficiency of CIGS solar cells with a chemical‐bath‐deposited ZnS buffer layer, the effect of the plasma damage by the sputter deposition of the ZnO : Al window layer should be understood. We have found that the efficiency of a CIGS solar cell consistently decreases with an increase in the sputtering power for the ZnO : Al window layer deposition onto the ZnS buffer layer because of plasma damage. To protect the ZnS/CIGS interface, a bilayer ZnO : Al film was developed. It consists of a 50‐nm‐thick ZnO : Al plasma protection layer deposited at a sputtering power of 50 W and a 100‐nm‐thick ZnO : Al conducting layer deposited at a sputtering power of 200 W. The introduction of a 50‐nm‐thick ZnO : Al layer deposited at 50 W prevented plasma damage by sputtering, resulting in a high open‐circuit voltage, a large fill factor, and shunt resistance. The ZnS/CIGS solar cell with the bilayer ZnO : Al film yielded a cell efficiency of 14.68%. Therefore, the application of bilayer ZnO : Al film to the window layer is suitable for CIGS solar cells with a ZnS buffer layer. Copyright © 2012 John Wiley & Sons, Ltd.     

Survey of ICIC techniques in LTE networks under various mobile environment parameters

LTE networks’ main challenge is to efficiently use the available spectrum, and to provide satisfying quality of service for mobile users. However, using the same bandwidth among adjacent cells leads to occurrence of Inter-cell Interference especially at the cell-edge. Basic interference mitigation approaches consider bandwidth partitioning techniques between adjacent cells, such as frequency reuse of factor m schemes, to minimize cell-edge interference. Although SINR values are improved, such techniques lead to significant reduction in the maximum achievable data rate. Several improvements have been proposed to enhance the performance of frequency reuse schemes, where restrictions are made on resource blocks usage, power allocation, or both. Nevertheless, bandwidth partitioning methods still affect the maximum achievable throughput. In this proposal, we intend to perform a comprehensive survey on Inter-Cell Interference Coordination (ICIC) techniques, and we study their performance while putting into consideration various design parameters. This study is implemented throughout intensive system level simulations under several parameters such as different network loads, radio conditions, and user distributions. Simulation results show the advantages and the limitations of each technique compared to frequency reuse-1 model. Thus, we are able to identify the most suitable ICIC technique for each network scenario.     

Evaluation of a proper controller performance for maximum-power point tracking of a stand-alone PV system

In this paper the implementation of a suggested stand-alone PV system, for maximum-power point tracking (MPPT), is carried out. Also, this paper presents a comparative study, through experimental work, between the conventional PI controller and the fuzzy logic controller (FLC) under different atmospheric conditions. The implemented system with both the PI controller and the FLC gives a good maximum-power operation of the PV array, but the tracking capability for different optimum operating points is better and faster for the case of using the FLC compared to the case of using the PI controller.     

A new iris localization method based on the competitive chords

This study introduces a novel iris localization method based on the competitive chords. The new method can be used to detect pupil?Ciris and iris?Csclera boundaries. The basic idea is to construct a set of chords from the left edges and the right edges of the pupil (or iris), and then find the winner chords with aligned centers. The winner chords can be used to vote to the correct pupil??s (or iris??s) center and radius. To verify the effectiveness of the proposed method, it is compared with two efficient techniques and applied to five datasets. The experimental results show that the new method is faster, more accurate and more robust than the state-of-the-art iris localization methods.     

Influences of Mn doping on the microstructural,semiconducting, and optoelectronic properties of HgO nanostructure films

Mn-doped HgO nanostructured thin films (Hg_1-xMn_xO) have been prepared using electron beam evaporation technique on Corning glass (1022) substrate at room temperature with different concentrations x = 0, 0.015, 0.05, 0.1, 0.15, and 0.2. The microstructural, morphological, semiconducting, and optoelectronic properties of the films have been investigated. The X-ray diffraction spectra suggest a hexagonal wurtzite type structure with lattice parameters decreased with increasing Mn content. It was found that the average particle size of the films decreases with increasing Mn doping which is confirmed by FE-SEM and AFM micrographs. The optical band gap of the investigated Mn-doped HgO nanocrystalline films is determined from the absorption coefficient and found to increase with the increase of Mn concentration which is attributed to the sp-d exchange interaction and/or the quantum confinement effect. The refractive index and extinction coefficient of the Mn-doped HgO films are also reported. The refractive index dispersion n(λ) is analyzed by single-effective-oscillator dispersion model proposed by the Wemple–DiDomenico (WDD). The oscillator parameters were estimated. The obtained dispersion values are suitable for the design of optoelectronic devices.