运动饮料配方设计概论

运动中，人体生理发生一系列的变化，包括水分损失、血糖／糖原消耗、电解质损失等，导致运动中／后的疲劳和运动能力下降。以运动中人体生理特点为基础，通过讨论运动前／中／后补充水、碳水化合物及电解质的问题，论证了运动饮料配方设计的原理依据。     

Microstrip stepped impedance resonator bandpass filter with an extended optimal rejection bandwidth

Bandpass filters with an optimal rejection bandwidth are designed using parallel-coupled stepped impedance resonators (SIRs). The fundamental (f/sub o/) and higher order resonant harmonics of an SIR are analyzed against the length ratio of the high-Z and low-Z segments. It is found that an optimal length ratio can be obtained for each high-Z to low-Z impedance ratio to maximize the upper rejection bandwidth. A tapped-line input/output structure is exploited to create two extra transmission zeros in the stopband. The singly loaded Q(Q/sub si/) of a tapped SIR is derived. With the aid of Q/sub si/, the two zeros can be independently tuned over a wide frequency range. When the positions of the two zeros are purposely located at the two leading higher order harmonics, the upper rejection band can be greatly extended. Chebyshev bandpass filters with spurious resonances up to 4.4f/sub o/, 6.5f/sub o/, and 8.2f/sub o/ are fabricated and measured to demonstrate the idea.     

The mechanics of compressive kinking in unidirectional fiber reinforced ductile matrix composites

Three distinct stages of kink band formation and propagation exist in ductile matrix composites subjected to compressive loading. These stages are called incipient kinking, transient kinking and kink band broadening. Each stage involves a different deformation mode. The mechanics governing each stage are discussed. Incipient kinking, where the peak load is attained, and kink band broadening, where the load attains a steady-state, are important in structural design. Two design philosophies are presented. References to pertinent literature are made throughout.     

The geometry effects for stress intensity factor of sandwich specimen for measuring interfacial fracture toughness

The interfacial stress intensity factors for three types of sandwich specimens: the single edge crack tensile specimen, the three point bend specimen and the four point shear specimen were obtained by the finite element analysis and compared with the asymptotic solutions. The results show that the geometric effect for mode II specimen is larger than mode I specimen. The limit curves for geometry factor equal to 1.05 were obtained to indicate the usable range of validity of the asymptotic solution.     

Delayed delivery of surviving triplet after fetal reduction and spontaneous abortion

In multiple pregnancies, survival of remaining fetuses after premature death and delivery of one fetus is uncommon. We report a case of a triplet pregnancy that was reduced to twins at the 14th gestational week and then had preterm premature rupture of membranes and intrauterine fetal death of one twin at the 17th gestational week. To save the surviving fetus, delivery of the dead fetus and ligation of the umbilical cord at the cervical level were performed. We also performed McDonald cervical cerclage to keep the placenta of the dead fetus as well as that of the surviving one in the uterine cavity. After a series of aggressive procedures, including immediate administration of tocolytic agents, and antibiotic prophylaxis to prevent infection and preterm labor, the surviving fetus was delivered vaginally 73 days later due to intractable uterine contractions. After a 10-week hospital stay, the infant boy, weighing 2,500 g, was discharged without any sequelae. To our knowledge, this was the longest interval between deliveries in a triplet pregnancy reported in Taiwan. With adequate intensive management, a satisfactory outcome of the fetus and mother in such cases is possible.     

2-D dopant profiling in VLSI devices using dopant-selectiveetching: an atomic force microscopy study

We report a detailed mapping of a 2-D dopant profile on a fully processed industrial sample with large dynamic range and high spatial resolution by utilizing a dopant-selective etching process and Atomic Force Microscopy. The experimental results show excellent agreement with those obtained from SRP and SIMS as corroborative methods. We also discuss the most critical factors which influence the applicability, reproducibility, and reliability of this method