Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Fabrication of lotus-type porous carbon steel by the continuous zone melting method and its mechanical properties

A lotus-type porous carbon steel with cylindrical pores was fabricated by the continuous zone melting method in a pressurized mixture of hydrogen and helium gases. The porosity increases with increasing partial pressure of the hydrogen gas, while the pore diameter remains almost constant, independent of the pressure. The ultimate tensile strength of the specimen with cylindrical pores parallel to the tensile direction is lower than the estimated value, assuming that the strength is decreased in proportion to the decrease of the cross-sectional area of the specimen, while the yield strength is higher than the estimated value. The compressive yield strength is also higher than the estimated value. The increase in yield strength is considered to be due to precipitation strengthening. The tensile strength is increased by quenching and tempering, while the elongation decreases. Such mechanical properties are discussed in terms of the microstructural analysis.     

Design for Consecutive Testability of System-on-a-Chip with Built-In Self Testable Cores

This paper introduces a new concept of testability called consecutive testability and proposes a design-for-testability method for making a given SoC consecutively testable based on integer linear programming problem. For a consecutively testable SoC, testing can be performed as follows. Test patterns of a core are propagated to the core inputs from test pattern sources (implemented either off-chip or on-chip) consecutively at the speed of system clock. Similarly the test responses are propagated to test response sinks (implemented either off-chip or on-chip) from the core outputs consecutively at the speed of system clock. The propagation of test patterns and responses is achieved by using interconnects and consecutive transparency properties of surrounding cores. All interconnects can be tested in a similar fashion. Therefore, it is possible to test not only logic faults but also timing faults that require consecutive application of test patterns at the speed of system clock since the consecutively testable SoC can achieve consecutive application of any test sequence at the speed of system clock.     

Preparation and antibacterial activity of novel fluoroalkyl end-capped oligomers/silica nanocomposites-encapsulated low molecular biocides

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA) _n -R_F] reacted with tetraethoxysilane (TEOS) and silica nanoparticles in the presence of low-molecular weight biocides such as hibitane, hinokitiol, and hinokioil under alkaline conditions to afford R_F-(DOBAA) _n -R_F/silica nanocomposites-encapsulated these biocides in excellent to moderate isolated yields. Fluoroalkyl end-capped N,N-dimethylacrylamide oligomer [R_F-(DMAA) _n -R_F] and acrylic acid oligomer [R_F-(ACA) _n -R_F]/silica nanocomposites-encapsulated hibitane were obtained under similar conditions. Dynamic light scattering measurements showed that the size of these fluorinated nanocomposites-encapsulated biocides thus obtained is nanometer size-controlled. Additionally, these fluorinated nanocomposites were shown to have a good dispersibility and stability in methanol and water. Of particular interest, these fluorinated nanocomposites-encapsulated biocides were found to have a good antibacterial activity against Staphylococcus aureus, and these nanocomposites were applied to the surface modification of traditional organic polymers such as poly(methyl methacrylate).     

Crack opening displacement of a through-wall crack in a plate subjected to bending load

This study was performed in order to clarify crack opening displacement (COD) of through-wall cracks in a plate subjected to bending load. The former COD evaluation methods were mainly developed corresponding to tensile load, but there has been nothing that has been developed corresponding to bending load. Therefore, the authors evaluated CODs of the through-wall cracks in plates which were subjected to a bending load using finite element method (FEM) analyses, and proposed a simplified COD evaluation method accounting for both tensile and bending loads. The proposed method is useful for leakage evaluation at a crack opening of an elbow crown or in the vicinity of the coolant surface of a vessel in which the bending stress is relatively large.     

Operant conditioning of hippocampal theta: Dissociating reward from performance deficits.

Dopaminergic blocking agents have been known to suppress intracranial self-stimulation, but whether the suppression results from a reduction in the rewarding value of stimulation or from motor deficits has remained controversial. We have resolved this controversy by developing an operant technique minimally dependent on motor activity; rats were trained to perform a bar-holding response for 3s or to produce hippocampal theta waves for 3s when the bar was retracted. Decamethonium bromide (a muscle relaxant) reduced bar holding without affecting theta production for brain stimulation. Pimozide (a dopaminergic blocking-agent) reduced both bar holding and theta production for stimulation, though rats were still capable of making the theta response at a rate comparable to the preinjection rate. Dopaminergic blocking at low doses reduces the rewarding value of brain stimulation at the level of the lateral hypothalamus. The method described in this report has wide applicability. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Establishment time of liquid flow in a bath agitated by bottom gas injection

The establishment time of gas-liquid two-phase flows in a cylindrical bath agitated by bottom gas injection through a central single-hole bottom nozzle was investigated. Because the turbulence intensity in the bath was comparable to or larger than the unity, the conventional definition of the flow establishment time based on the history of mean velocity was not suitable for the present case. In fact, it was difficult to determine the flow establishment time based on the well-known 90 or 99 pct criterion for the mean velocity. Accordingly, two methods of determining the flow establishment time by focusing on the turbulence components instead of the mean velocity components were proposed. Velocity measurements were made with a two-channel laser Doppler velocimeter. The flow establishment time was correlated as a function of gas flow rate. Close agreement was obtained by the two methods.     

A 0.1-μm delta-doped MOSFET fabricated with post-low-energyimplanting selective epitaxy

A simple fabrication technology for delta-doped MOSFETs, named post-low-energy implanting selective epitaxy (PLISE) is presented. The PLISE technology needs no additional photo-lithography mask, deposition step or etching step even for CMOS devices. The only additional step is growing undoped epitaxial channel layers by UHV-CVD after the channel implantation. With this technology, delta-doped NMOSFETs with 0.1-μm gate length were successfully fabricated. By optimizing the epi-layer thickness and the channel doping level, short-channel effects are suppressed enough to achieve 0.1-μm gate length. Moreover, the junction capacitance at zero bias is reduced by 50%     

Intestinal metaplasia with adherent Helicobacter pylori: a hybrid epithelium with both gastric and intestinal features

Helicobacter pylori seem to avoid areas of intestinal metaplasia in the gastric mucosa, but attachment of these bacteria to epithelium with the appearance of incomplete intestinal metaplasia has been documented. To characterize the nature of the epithelium to which H pylori was attached, we carried out an immunohistochemical study using monoclonal antibodies against gastric surface mucous cell mucins (M1), blood group-related carbohydrates antigens (Le(a), sialyl Le(a), Le(b), type 1H, and type 2H) and sialyl Tn antigen. The results of this study suggest that these areas of H pylori attachment represent a hybrid epithelium whose cells share characteristics of both gastric surface mucous cells and intestinal metaplastic cells. Whether all areas of incomplete intestinal metaplasia represent an intermediate stage between the normal gastric epithelium and the fully developed complete type of metaplasia remains to be determined.     

Subsurface structures in initial stage of FeSi2 growth studied by high-resolution Rutherford backscattering spectroscopy

The initial stage of iron silicide formation is investigated by high-resolution Rutherford backscattering spectroscopy. During the Fe deposition on Si(001) at 470 °C, the formation of FeSi₂ is confirmed by the surface peak analysis. Initially, FeSi₂ grows epitaxially so that one of the major crystallographic axes is parallel to the <111> axis of the Si substrate. With increasing Fe deposition, the deviation between the major crystallographic axis of the silicide region and Si<111> increases although the electron diffraction pattern is independent of the amount of Fe deposition. Therefore, the subsurface crystallographic structure of iron silicide is transformed from a cubic-like to a low-symmetry structure.