单壁纳米碳管/纳米铝基复合材料的增强效果

用半连续氢电弧法和活性氢等离子蒸发法分别制备出单壁纳米碳管(SWNTs)和纳米A1粉体，然后用提纯后的SWNTs和纳米A1粉体制备出SWNTs含量(质量分数)分别为0、2．5％、5．0％、7．5％和10.0％的单壁纳米碳管／纳米铝基块体复合材料．SWNTs对高强度纳米A1基体具有显著的增强作用，当SWNTs含量小于5．0％时，材料的硬度随着SWNTs含量的提高线性上升．其中5％SWNTs和纳米A1的复合增强效果最好，其硬度可达2.89GPa，大约是粗晶A1(0．15GPa)的20倍．当SWNTs含量超过5．0％时，增强效果开始缓慢的下降．讨论了单壁纳米碳管增强纳米铝基复合材料的强化机制．     

超低膨胀陶瓷K_（2x）Ba_（1－x）Zr_4（PO_4）_6系统的X射线衍射

用高温Ｘ射线衍射方法对磷酸锆钡钾系统陶瓷材料的各向异性热膨胀作了研究．对七个组份试样的７７套高温Ｘ射线衍射图作了仔细的指标化和精密点阵常数测定．点阵常数随温度作非线性变化·对Ｋ_２ｘＢａ_１－ｘＺｒ_４（ＰＯ_４）_６的不同组份不同温度（３００～１３００Ｋ）的热膨胀系数。α_ａ、α_ｃ、　作了测定·该系统零膨胀陶瓷的组份为Ｋ_１．１６Ｂａ_０．４２Ｚｒ_４（ＰＯ_４）_６（ｘ＝０．５８）     

甲状腺素T4免疫传感器的研究

报道以甲基丙烯酸羟乙酯与甲基丙烯酸甲酯的共聚物为载体膜材料，研制成非酶标记的Ｔ４免疫传感器，并对载体膜材料的共聚方法及共聚物共聚比与传感器灵敏度的关系进行了探讨。     

Gr（C）纤维增强镁基复合材料的界面结构

采用真空—压力浸渗工艺制备Ｇｒ（Ｃ）／Ｍｇ复合材料，Ｇｒ／Ｍｇ材料界面上无化学反应迹象，有析出物γ相（Ｍｇ１７Ａｌ１２），该析出物形状、大小与制备工艺条件，主要是纤维预制件温度有关。Ｃ／Ｍｇ复合材料界面Ａｌ含量较基体高出２倍多，文中分析了可能的原因     

Artificial neural network approaches on composition-property relationships of jet fuels based on GC-MS

The relationships of composition-properties of 80 jet fuels concerning chemical compositions and several specification properties including density, flashpoint, freezing point, aniline point and net heat of combustion were studied. The chemical compositions of the jet fuels were determined by GC-MS, and grouped into eight classes of hydrocarbon compounds, including n-paraffins, isoparaffins, monocyclopraffins, dicyclopraffins, alkylbenzens, naphthalenes, tetralins, hydroaromatics. Several quantitative composition-property relationships were developed with three artificial neural network (ANN) approaches, including single-layer feedforward neural network (SLFNN), multiple layer feedforward neural network (MLFNN) and general regressed neural network (GRNN). It was found that SLFNNs are adequate to predict density, freezing point and net heat of combustion, while MLFNNs produce better results as far as the flash point and aniline point prediction are concerned. Comparisons with the multiple linear regression (MLR) correlations reported and the standard ASTM methods showed that ANN approaches of composition-property relationships are significant improvement on MLR correlations, and are comparable to the standard ASTM methods.     

TDE-85环氧树脂丙烯酸酯的合成及其UV固化特性的研究

本文研究了TDE-85环氧树脂丙烯酸酯的合成方法，讨论了合成条件（催化剂的种类与用量，反应温度及时间，投料比，反应类型及不饱和酸种类的选择等）对合成反应及合成产物性状的影响。另外，还考察了该合成产物的UV固化特性。     

α—溴代异丁酸叔丁酯合成的研究

研究了α－溴代异丁酸叔丁酯的合成方法以及几种溶剂和有机碱对反应的影响。结果表明，在三种酰卤中，羧酸酰氯的酯化收率最高；有机碱采用三乙胺，以苯作溶剂效果最佳。     

Sealing of Ejection Hole at the Bottom of Projectile for Wired Transmission System of Penetration Data

It is difficult to find the projectile when people want to get the penetration data in a hard recovery method, so a recovery system of penetration data is designed based on an ejection mode from the projectile base and a method of wired transmission, at the same time, the system was sealed with a designed sealing device, the working principle of which was introduced. Using Fluent as the simulation platform, the transient pressure of seal cavity was simulated based on the change of chamber pressure, and steady-state pressure of seal clearance and seal cavity were simulated based on the maximum chamber pressure. The sealing performance was tested by a pressure test system. The results of simulation and experiment show that the maximum pressure of seal cavity is 139.4.kPa when the maximum chamber pressure is 242.9.MPa and the maximum temperature of gunpowder explosive gas is 2.166.5.K, so the sealing performance can be assured. The sealing device can be taken as a reference in sealing research on gunpowder gas at the bottom of projection.     

基于GIS的云龙示范区土地利用转移分析

土地利用变化的空间特征和变化规律分析是区域规划的重要依据。在RS/GIS技术支持下,以云龙示范区2005和2010年2期遥感数据为主要数据源,结合相关软件进行图像及数据的处理;运用土地利用转移矩阵和土地利用动态度、土地变化强度等指标对研究区土地利用的空间变化进行了研究。结果表明:5年间云龙示范区土地利用变化总量为48.61 hm2,增长3.26%;土地利用动态度差异明显,林地和水域面积维持稳定,但建设用地和耕地变化较大,土地利用变化强度为0.65。该结果可为区域土地利用动态监测提供数据支撑,也可为云龙示范区规划及建设提供参考依据。     

新型非离子型水性环氧固化剂的合成及性能研究

为提高水性环氧涂料的固化性能和适用期,以自制聚酰胺和生物基戊二胺为起始原料,聚乙二醇二缩水甘油醚（ PEGGE）为亲水链段,双酚 A型环氧树脂（ E-51）为疏水链段,邻甲苯缩水甘油醚（ CGE）为封端剂制备了非离子型低温水性环氧固化剂,并与自制水性环氧乳液复配制得双组分水性环氧涂料。考察了环氧固化剂合成工艺参数及涂膜各项性能。结果表明：该固化剂含有较长的柔性脂肪烃碳链和聚醚链段能够提高涂膜的柔韧性;双酚 A型环氧树脂参与扩链反应能够解决与乳液不兼容等问题;苯环结构增加了涂膜的硬度;涂膜室温固化后性能优异,具有良好的物理机械性能、耐水性、耐酸碱性和耐盐雾性。