Power spectral density of CMI-coded TV signal transmitted through fibre-optic heterodyne system

An expression is derived for the power spectral density of a coded mark inversion (CMI) TV signal transmitted through a fibre-optic heterodyne system. An illustrative example is given, and its power spectral density has been computed numerically.     

在双镶嵌铜互联中O.13微米器件生成用的基于PVD和ALD阻挡层的先进技术

1. Introduction The requirement of minimal bottom coverageand thick sidewall coverage for PVD-based films forlow via resistance and improved stress migration isnot easy to achieve with traditional depositionmethods. Modern I-PVD techniques give high bot-tom coverage, due to the ionized component of thedeposition flux. Sidewall coverage tends to be low,which is mainly due to off-normal deposition fluxand a less than unity sticking coefficient.     

Postnatal survival and growth of mouse irradiated in utero with low dose

In order to investigate radiation risks associated with low dose and low dose-rates, pregnant Swiss albino mice were exposed to gamma rays, 0.80 Gy from a cobalt-60 source at two different dose-rates (0.0795 and 0.0012 Gy/min) on 18 day post conception. In females exposed to lower dose-rate (0.0012 Gy/min), litter size was found to be decreased, while those exposed to higher dose-rate (0.0795 Gy/min), it remained unaltered. In both groups, appearance of fur and development of complete fur were delayed, whereas gait was delayed only in higher dose-rate group. Male offspring exhibited a biphasic mode of weight loss, while female offspring after an initial weight loss at 1 week, displayed a continuous recovery, but could not attain the normal weight till 12 weeks of age. It appears that higher dose-rate is more effective in delaying the appearance of physiological markers and weight loss, while in terms of litter size lower dose-rate (0.0012 Gy/min) is more effective.     

A renewable approach toward the development of mahua oil‐based wood protective polyurethane coatings: Synthesis and performance evaluation

In the current scenario, the demand for renewable resources is increasing day by day due to numerous factors. In view of this, current work represents the preparation of wood protective polyurethane (PU) coatings from mahua oil. Mahua oil was used as a starting material for the synthesis of fatty amide by base catalyzed aminolysis reaction. The synthesized fatty amide was converted into the polyetheramide polyols by a condensation reaction with bisphenol C. The structure of the synthesized products was confirmed by the attenuated total reflection‐Fourier transform infrared and ¹H‐NMR spectroscopy. The synthesized polyetheramide polyols were used as precursors for the preparation of PUs and the prepared PUs were applied on the wood surface as a protective coating. The coating performance of the PUs was evaluated by the measurement of mechanical, thermal, and microbial properties as well as water, solvent, and chemical resistance. The coating performance revealed that mahua oil can be used as a renewable resource for the preparation of wood protective PUs. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46722.     

Application of DKMQ24 shell element for twist of thin-walled beams: Comparison with Vlassov theory

This article presents the application of DKMQ24 shell element for twist of thin-walled beams. This element passed the patch tests for membrane, bending and shear problems and gave fine results for plate and shell problems analysis without shear locking. Thin-walled cantilever beams are analyzed using this element. DKMQ24 gives good results for cantilever beams with open cross-section for a very few number of element. Moreover, the comparison of the results obtained with Vlassov analytical solution enables to evaluate the accuracy of the twist rigidity, J_d, which depends on an empirical coefficient in Vlassov theory.     

Carburizing of Duplex Stainless Steel (DSS) Under Compression Superplastic Deformation

A new surface carburizing technique which combines superplastic deformation with superplastic carburizing (SPC) is introduced. SPC was conducted on duplex stainless steel under compression mode at a fixed 0.5?height reduction strain rates ranging from 6.25?×?10^?5?to 1?×?10^?3?s^?1?and temperature ranging from 1173?K to 1248?K (900?°C to 975?°C). The results are compared with those from conventional and non-superplastic carburizing. The results show that thick hard carburized layers are formed at a much faster rate compared with the other two processes. A more gradual hardness transition from the surface to the substrate is also obtained. The highest carburized layer thickness and surface hardness are attained under SPC process at 1248?K (975?°C) and 6.25?×?10^?5?s^?1?with a value of (218.3?±?0.5)???m and (1581.0?±?5.0) HV respectively. Other than that, SPC also has the highest scratch resistance.     

Development of Cutting Tool Through Superplastic Boronizing of Duplex Stainless Steel

In this study, a cutting tool is developed from duplex stainless steel (DSS) using the superplastic boronizing technique. The feasibility of the development process is studied, and the cutting performances of the cutting tool are evaluated and compared with commercially available carbide and high-speed steel (HSS) tools. The superplastically boronized (SPB) cutting tool yielded a dense boronized layer of 50.5 µm with a surface hardness of 3956 HV. A coefficient of friction value of 0.62 is obtained, which is lower than 1.02 and 0.8 of the carbide and HSS tools. When tested on an aluminum 6061 surface under dry condition, the SPB cutting tool is also able to produce turning finishing below 0.4 µm, beyond the travel distance of 3000 m, which is comparable to the carbide tool, but produces much better results than HSS tool. Through superplastic boronizing of DSS, it is possible to produce a high-quality metal-based cutting tool that is comparable to the conventional carbide tool.     

Growth of Rhizobium leguminosarum on peat in rotating bioreactors

The legume inoculant Rhizobium leguminosarum was grown on peat in roller bottles and a rotating drum bioreactor. Growth conditions were first determined using experiments in roller bottles. The best growth rate and cell count were obtained with peat containing 40% moisture (wet basis) and a volume fraction of moist peat of 0.3 in the roller bottle bioreactors. A cell count of 1.3 to 1.9 × 10⁹ CFU/g was achieved in 4 d or less, from an initial inoculum of 10⁶ CFU/g. In a rotating drum bioreactor, the growth of R.leguminosarum on peat with sucrose as the main carbon source was completed after 4 d. The majority of growth was in the first 2 d, based on carbon dioxide evolution. These results showed that growth of R. leguminosarum was more rapid in the rotating drum than in bags of peat, due to enhanced oxygen transfer.