Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

Enhancement mode InP MISFET's with sulfide passivation andphoto-CVD grown P3N5 gate insulators

High performance enhancement mode InP MISFET's have been successfully fabricated by using the sulfide passivation for lower interface states and with photo-CVD grown P₃N₅ film used as gate insulator. The MISFET's thus fabricated exhibited exhibited pinch-off behavior with essentially no hysteresis. Furthermore the device showed a superior stability of drain current. Specifically under the gate bias of 2 V for 10⁴ seconds the room temperature drain current was shown to reduce from the initial value merely by 2.9% at the drain voltage of 4 V. The effective electron mobility and extrinsic transconductance are found to be about 2300 cm ²/V·s and 2.7 mS/mm, respectively. The capacitance-voltage characteristics of the sulfide passivated InP MIS diodes show little hysteresis and the minimum density of interface trap states as low as 2.6×10¹⁴/cm² eV has been attained     

Pressure effects on flow and fracture of Be-Al alloys

The flow and fracture behavior of Be-Al alloys were determined in tension with different levels of superimposed pressure. The Be-Al alloys were prepared by Brush Wellman, Inc. (Cleveland, OH) from prealloyed powders processed to either a hot isostatically pressed (“hipped”) or cold isostatically pressed and extruded condition. Significant effects of pressure on both the flow and ductility have been observed at room temperature, with implications on the formability of these materials. The effects of changes in processing conditions and stress state on the flow and fracture behavior are summarized in addition to both optical and scanning electron microscopy (SEM) examination of the fracture surfaces. Separate other studies on the alloy constituents (e.g., Al and Be) are also reported. The results are also compared to previous works on monolithic materials and composites tested with high pressure.     

A note on computing environments and network reliability

Interest has increased during recent years in using microcomputers for implementation of network reliability algorithms. There are indications that some implementations suffer severe restrictions imposed by such a computing environment, whereas some other results indicate otherwise. This brief note attempts to clarify the apparently contradictory conclusions that would be naturally drawn from recent papers that treat this subject.     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Dependence of properties of liquid crystalline aromatic copolyesters on monomer sequence-copolyesters derived from terephthalic acid, 2,7-naphthalenediol and p-hydroxybenzoic acid

Summary An aromatic copolyester with the ordered sequence of terephthalic acid (TA)-p-hydroxybenzoic acid (HB)-2,7-naphthalenediol (ND)-p-hydroxybenzoic acid (HB) was prepared and its properties were compared with those of the corresponding random copolyester having the same overall monomer composition. Thermal and crystallizing properties of the two polymers are quite different. The former exhibits significantly higher glass transition and melting temperatures than the latter. The former's degree of crystallinity also is much higher than the latter's. Both polymers are thermotropic and form nematic melts.     

Polyunsaturated fatty acids in tissues of rats fed trielaidin and high or low levels of linolenic acid

Male and female weanling rats that were born to dams fed a diet low in linolenic acid received diets of 15% lipids by weight containing 45% elaidic acid (as trielaidin) and 8.5% or 0.1% linolenic acid for 10 weeks. Four other groups, in which palmitic or oleic acid replaced elaidic acid in the diet, served as controls. The fatty acid profiles of several lipid classes were determined in adipose tissue, adrenals, testes, heart and brain. Elaidic acid was incorporated into tissue lipids in varying degrees, depending on the organ and on the lipid class. Feeding elaidic acid induced no changes in the polyunsaturated fatty acid (PUFA) profiles of testes lipids but resulted in definite modifications of the PUFA patterns of heart phosphatidylcholine (PC) and phosphatidylethanolamine (PE). In linolenic acid-deprived rats, arachidonic acid was decreased in PC and linoleic acid was increased in both PC and PE; 22∶5n−6 was strongly depressed in both PC and PE. In linolenic acid-fed rats, 22∶6n−3 was decreased in PC and PE. These changes, on the whole, were more evident in females, and some also were observed in adrenal cholesteryl esters but only slightly in brain phospholipids. the apparent inhibition of the biosynthesis of PUFA induced by dietary elaidic acid appeared to be complex and of greater intensity in the n−6 fatty acid series than in their n−3 homologues.     

Interest of molecular functionalization for electrochemical storage

Despite great interests in electrochemical energy storage systems for numerous applications, considerable challenges remain to be overcome. Among the various approaches to improving the stability, safety, performance, and cost of these systems, molecular functionalization has recently been proved an attractive method that allows the tuning of material surface reactivity while retaining the properties of the bulk material. For this purpose, the reduction of aryldiazonium salt, which is a versatile method, is considered suitable; it forms robust covalent bonds with the material surface, however, with the formation of multilayer structures and sp³ defects (for carbon substrate) that can be detrimental to the electronic conductivity. Alternatively, non-covalent molecular functionalization based on π–π interactions using aromatic ring units has been proposed. In this review, the various advances in molecular functionalization concerning the current limitations in lithium-ion batteries and electrochemical capacitors are discussed. According to the targeted applications and required properties, both covalent and non-covalent functionalization methods have proved to be very efficient and versatile. Fundamental aspects to achieve a better understanding of the functionalization reactions as well as molecular layer properties and their effects on the electrochemical performance are also discussed. Finally, perspectives are proposed for future implementation of molecular functionalization in the field of electrochemical storage.

Open image in new window