κ-Opioid Signaling in the Lateral Hypothalamic Area Modulates Nicotine-Induced Negative Energy Balance

Several studies have reported that nicotine, the main bioactive component of tobacco, exerts a marked negative energy balance. Apart from its anorectic action, nicotine also modulates energy expenditure, by regulating brown adipose tissue (BAT) thermogenesis and white adipose tissue (WAT) browning. These effects are mainly controlled at the central level by modulation of hypothalamic neuropeptide systems and energy sensors, such as AMP-activated protein kinase (AMPK). In this study, we aimed to investigate the kappa opioid receptor (κOR)/dynorphin signaling in the modulation of nicotine’s effects on energy balance. We found that body weight loss after nicotine treatment is associated with a down-regulation of the κOR endogenous ligand dynorphin precursor and with a marked reduction in κOR signaling and the p70 S6 kinase/ribosomal protein S6 (S6K/rpS6) pathway in the lateral hypothalamic area (LHA). The inhibition of these pathways by nicotine was completely blunted in κOR deficient mice, after central pharmacological blockade of κOR, and in rodents where κOR was genetically knocked down specifically in the LHA. Moreover, κOR-mediated nicotine effects on body weight do not depend on orexin. These data unravel a new central regulatory pathway modulating nicotine’s effects on energy balance.     

Localized corrosion of (lean) duplex stainless steels in immersion units of urban wastewater treatment plants

With lower alloying cost and higher mechanical properties, lean duplex stainless steels can be an alternative to the more commonly used austenitic stainless steels. However, these alloys are still not the preferred choice, probably due to a lack of field experience. A study was thus initiated in view of defining the limits of use of selected (lean) duplexes for urban wastewater treatment units. The present paper shows the localized corrosion performance of selected lean duplexes in chloride contaminated solutions. The results are compared with austenitic S30403 and S31603 and with the more standard duplexes S82441 and S32205. The effect of welding was also investigated. Exposures in field municipal wastewater plants were conducted for 1 year in low and high chloride content units. The results show that lean duplexes S32101 and S32202 can be used as alternatives to S30403 and S31603 in low chloride electrolytes. At 500 ppm of chloride content, duplex stainless steel S32304 showed better corrosion resistance than S30403 and S31603. For higher chloride contents (1000 ppm and above) the standard duplexes S82441 and S32205 shall be preferred.     

用于便携无线设备的Wireless TrenchTM技术

射频电路设计人员常用的一条经验法则是:有源器件的fT至少应为工作频率的十倍时,现代无线设备中的射频电路才会具有良好的性能.     

Manufacturing method for monolithic dye-sensitised solar cells permitting long-term stable low-power modules

A manufacturing technique for monolithic dye-sensitised solar cells is presented. Encapsulated modules designed for indoor low-power applications have been prepared using industrial methods and equipment. Under certain conditions (light intensity <5000 lx, temperature between –10°C and 50°C, and relative humidity of appr. 50%), the modules have performed well and shown excellent long-term stability. Moreover, modules withstand illumination in combination with storage at 100% relative humidity. However, a certain degradation of the module performance takes place at illuminations exceeding 5000 lx and temperatures exceeding 50°C.     

Integrated Smart Sensor Calibration

In many applications electronic sensors are used toimprove performance and reliability of measurement systems. Suchsensors should provide a correct transfer from the physical signalto be measured to the electrical output signal. One importantstep to achieve this, is to calibrate each sensor by applyingdifferent reference input signals and adjusting the sensor transferaccordingly. Besides expensive reference equipment the calibrationprocess takes much time and attention per individual sensor,which means a considerable increase in sensor production costs.By including at the sensor or sensor interface chip a programmablecalibration facility the calibration of such smart sensors caneasily be automated and can be executed for a batch of sensorsat a time, thus minimizing the calibration time and costs. Thispaper presents a calibration method and options for integrationin the smart sensor concept, in hardware as well as in software.An advantage of the proposed method is that it does not needa large matrix of calibration data, which needs to be storedin a look-up table or converted into a correction formula, butinstead it uses a step-by-step approach to correct the sensortransfer at each calibration measurement until the error is sufficientlysmall.     

Photonic Demodulator With Sensitivity Control

A current assisted photonic demodulator for use as a pixel in a 3-D time-of-flight imager shows nearly 100% static demodulator contrast and is operable beyond 30 MHz. An integrated tunable sensitivity control is also presented for increasing the distance measurement range and avoiding unwanted saturation during integration periods. This is achieved by application of a voltage on a dedicated drain tap showing a quenching of sensor sensitivity to below 1%     

High optical power electroabsorption waveguide modulator

A sampled grating distributed Bragg reflector-laser integrated with a waveguide Franz-Keldysh modulator is investigated for high optical power applications. The EAM modulation efficiency is demonstrated to asymptotically approach a limit determined by the internal differential photodetector efficiency. Linear photocurrent and 1 dB small signal AC compression point both exceed 70 mA, indicating high saturation power.