Multimedia content recommendation in social networks using mood tags and synonyms

Multimedia Systems - The preferences of Web information purchasers are changing. Cost-effectiveness (i.e., an emphasis on performance with respect to price) is becoming less regarded than...     

Multiply Charged Conjugated Polyelectrolytes as a Multifunctional Interlayer for Efficient and Scalable Perovskite Solar Cells

A series of anionic conjugated polyelectrolytes (CPEs) is synthesized based on poly(fluorene-co-phenylene) by varying the side-chain ionic density from two to six per repeat units (MPS2-TMA, MPS4-TMA, and MPS6-TMA). The effect of MPS2, 4, 6-TMA as interlayers on top of a hole-extraction layer of poly(bis(4-phenyl)-2,4,6-trimethylphenylamine (PTAA) is investigated in inverted perovskite solar cells (PeSCs). Owing to the improved wettability of perovskites on hydrophobic PTAA with the CPEs, the PeSCs with CPE interlayers demonstrate a significantly enhanced device performance, with negligible device-to-device dependence relative to the reference PeSC without CPEs. By increasing the ionic density in the MPS-TMA interlayers, the wetting, interfacial defect passivation, and crystal growth of the perovskites are significantly improved without increasing the series resistance of the PeSCs. In particular, the open-circuit voltage increases from 1.06 V for the PeSC with MPS2-TMA to 1.11 V for the PeSC with MPS6-TMA. The trap densities of the PeSCs with MPS2,4,6-TMA are further analyzed using frequency-dependent capacitance measurements. Finally, a large-area (1 cm²) PeSC is successfully fabricated with MPS6-TMA, showing a power conversion efficiency of 18.38% with negligible hysteresis and a stable power output under light soaking for 60 s.     

Bioactive compounds and antioxidant activities of the Korean lotus leaf (Nelumbo nucifera) condiment: volatile and nonvolatile metabolite profiling during fermentation

Recent studies have shown that lotus (Nelumbo nucifera) leaf has various pharmacological effects. However, there have been no scientific investigations into these leaves as a fermented crude liquid. This study compared the in vitro antioxidant capacity of lotus leaf‐fermented broth (LLFB) with that of 57° Brix sugar broth (SB) as a control over a period of 6 months based on 1,1‐diphenyl‐2‐picrylhydrazyl radical scavenging activity, ferric ion reducing power, superoxide dismutase‐like activity, tyrosinase inhibition and nitrite scavenging activity. The dominant species during fermentation process were Leuconostoc lactis and Saccharomyces cerevisiae for LLFB. A total of thirty‐six metabolites such as alkaloids, fatty acids, organic acids, phenolics, sugar and sugar derivatives, ethyl esters and monoterpenoids differed between SB and LLFB using gas chromatography–mass spectrometry. Meanwhile, nine volatile compounds in LLFB contributed pleasant, slightly sweetish and fruity odour of condiment and sensory evaluation score of 4.06 ± 1.52 in the proportion of 1:9 LLFB/water.     

Small‐Sized High‐Power PIN Diode Switch with Defected Ground Structure for Wireless Broadband Internet

This letter presents a small‐sized, high‐power single‐pole double‐throw (SPDT) switch with defected ground structure (DGS) for wireless broadband Internet application. To reduce the circuit size by using a slow‐wave characteristic, the DGS is used for the quarter‐wave (°/4) transmission line of the switch. To secure a high degree of isolation, the switch with DGS is composed of shunt‐connected PIN diodes. It shows an insertion loss of 0.8 dB, an isolation of 50 dB or more, and power capability of at least 50 W at 2.3 GHz. The switch shows very similar performance to the conventional shunt‐type switch, but the circuit size is reduced by about 50% simply with the use of DGS patterns.     

Pyrolysis of Miscanthus Giganteus and wood pellets: TG-FTIR analysis and reaction kinetics

Characterisation of two biomass fuels (pelletised Miscanthus Giganteus and wood) was performed using thermogravimetric analysis with measurement of products by means of Fourier transform infrared spectroscopy (TG-FTIR). Three heating rate profiles were applied (10, 30 and 100 °C/min), with a final temperature of 900 °C. HCN and HNCO were found to be the major N-products, while the NH₃ fraction was detected to a minor extent. Kinetic parameters were obtained from the TG-FTIR results using a model based on parallel first-order reactions with a Gaussian distribution of activation energies. On the basis of the above kinetic analysis and product yields, input files for the functional group-devolatilisation, vaporisation, cross-linking biomass-pyrolysis model were prepared. The fit of model parameters to TG-FTIR product-evolution data was found to be generally good, but the model-predicted yields for some species did not fit experimental data at all heating rates. Further improvements in the model are needed to resolve above difficulty.     

台北101层国际金融中心之结构施工技术与其设计考量概述

本文旨在简要说明目前正在施工中之超高层大楼—台北国际金融中心之结构系统、钢结构工程、钢筋混凝土工程基础与深开挖工程等特殊施工技术,并佐以相关之设计考量与施工规划概要,以供工程界做参考。     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

Study on the c-axis preferred orientation of ZnO film on various metal electrodes

ZnO thin film was deposited on various metal electrodes by reactive sputtering, and c-axis preferred orientation of the film has been studied. ZnO, which has high piezoelectricity, is promising for oscillators or filter devices such as surface acoustic wave (SAW) device, gas sensor, and film bulk acoustic resonator (FBAR). But, for the application of ZnO film for these devices, the film should be grown with c-axis normal to the electrode. In this study, Pt, Al, and Au were deposited on Si wafer, and the surface roughness and crystal structure of the ZnO film on the electrode were investigated using AFM, scanning electron microscopy (SEM), and X-ray diffraction (XRD). Columnar structures of ZnO films were grown with c-axis normal to all electrodes, and among them Pt electrode showed the highest preferred orientation of ZnO film.     

Model development for multicomponent mass transfer with rapid chemical reactions in a small drop

Multicomponent mass transfer accompanied by instantaneous chemical reactions in a small drop has been modeled and simulated for the case where two different solutes diffuse from a continuous phase into the drop and react rapidly with a third reactant in the drop. The computational results obtained by Galerkin’s finite element method are reported in terms of concentration profiles, the locations of reaction front, the cumulative mass flux, and the enhancement factor. The effects of physical parameters, such as diffusivities of the solutes and the reactant, the interfacial concentration of solutes, and the relative amount of the reactant, on the calculated quantities are discussed.