Time reversibility of the discrete element method

An algorithm is presented for discrete element method simulations of energy-conserving systems of frictionless, spherical particles in a reversed-time frame. This algorithm is verified, within the limits of round-off error, through implementation in the LAMMPS code. Mechanisms for energy dissipation such as interparticle friction, damping, rotational resistance, particle crushing, or bond breakage cannot be incorporated into this algorithm without causing time irreversibility. This theoretical development is applied to critical-state soil mechanics as an exemplar. It is shown that the convergence of soil samples, which differ only in terms of their initial void ratio, to the same critical state requires the presence of shear forces and frictional dissipation within the soil system.     

Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

Evaluating the Use of Daily Care Notes Software for Older People with Dementia

There has been little research to investigate the impact of software to support the care for older people with dementia care. This article reports the evaluation of software adapted to support one key person-centered task for the care of older residents with dementia – recording and sharing daily care notes. The evaluation on the dementia wing of 1 residential home for over 6 months revealed that use of the software on mobile devices carried by the carers increased the number and volume of daily care notes recorded, but only for the types of content that were already being recorded by carers. Carers reported more advantages that resulted from daily care notes once in digital form than from the documenting task, as well as barriers to the use of mobile digital software to record daily care notes.     

Differences between oculomotor and perceptual artifacts for temporally limited head mounted displays

We used perceptual and oculomotor measures to understand the negative impacts of low (phantom array) and high (motion blur) duty cycles with a high‐speed, AR‐likehead‐mounted display prototype. We observed large intersubject variability for the detection of phantom array artifacts but a highly consistent and systematic effect on saccadic eye movement targeting during low duty cycle presentations. This adverse effect on saccade endpoints was also related to an increased error rate in a perceptual discrimination task, showing a direct effect of display duty cycle on the perceptual quality. For high duty cycles, the probability of detecting motion blur increased during head movements, and this effect was elevated at lower refresh rates. We did not find an impact of the temporal display characteristics on compensatory eye movements during head motion (e.g., VOR). Together, our results allow us to quantify the tradeoff of different negative spatiotemporal impacts of user movements and make subsequent recommendations for optimized temporal HMD parameters.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

A concept for the generation of out-of-plane distortion from tailored FRP laminates

The phenomenon of thermally induced distortions in unsymmetrical laminates is well understood, and it may be shown that a square, unsymmetrical 0.90 laminate will tend to form two stable geometries with a snap-through phenomenon between them. This paper discusses laminates in which at each point the lay-up is symmetrical across the laminate mid-plane, but which still exhibit multiple stable geometries. The number of stable geometries can be controlled by the details of the lay-up from the minimum of two to, in principle, an unlimited number. In addition it will be shown how a similar process can be used to generate multiple stable stress states and geometries in unidirectional laminates. This paper represents a very preliminary experimental investigation of the design space available for such composite laminates. Possible applications of composites with multiple stable geometries are noted.     

A Built-in Self-Test Scheme with Diagnostics Support for Embedded SRAM

In this paper we propose a novel built-in self-test (BIST) design for embedded SRAM cores. Our contribution includes a compact and efficient BIST circuit with diagnosis support and an automatic diagnostic system. The diagnosis module of our BIST circuit can capture the error syndromes as well as fault locations for the purposes of repair and fault/failure analysis. In addition, our design provides programmability for custom March algorithms with lower hardware cost. The combination of the on-line programming mode and diagnostic system dramatically reduces the effort in design debugging and yield enhancement. We have designed and implemented test chips with our BIST design. Experimental results show that the area overhead of the proposed BIST design is only 2.4% for a 128 KB SRAM, and 0.65% for a 2 MB one.     

Adaptive motion control using neural network approximations

In this paper, we present a new adaptive technique for tracking control of mechanical systems in the presence of friction and periodic disturbances. Radial Basis Functions (RBFs) are used to compensate for the effects of nonlinearly occurring parameters in the friction and periodic disturbance model. Theoretical analysis, such as stability and transient performance, is provided. Furthermore, the performance of the adaptive RBF controller and its non-adaptive counterpart are compared.     

Topology preservation of template-based 6-subiteration reduction operations

Generally, a reduction operation (e.g., thinning and shrinking) on 3D binary images can be represented as a set of reduction templates where every object voxel of the image satisfying any template is turned to a background voxel. Generally, it is rather difficult, error-prone and time-consuming for verifying the topological soundness of a 3D parallel reduction operation. This paper proposes sufficient conditions of time complexity O(n) for verifying the topological soundness of 3D parallel 6-subiteration reduction operations of n templates where such a kind of 3D reduction operations is performed alternatively from the six orthogonal directions to turn object voxels to background voxels. By such sufficient conditions, the topology soundness of a 3D 6-subiteration parallel reduction operation can be verified by checking each and every of its templates.