Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Early patterning of prelimbic cortical axons to the striatal patch compartment in the neonatal mouse

The striatum receives excitatory input from virtually the entire cerebral cortex. In the adult, this input is segregated into two functionally distinct compartments of the striatum, the patch (striosome) and matrix regions. This study determined whether the patterning of corticostriatal afferents from the prelimbic cortex to the striatal patch compartment develops during the early period of collateral formation or instead at the time of peak synaptogenesis. Initial formation of corticostriatal axon collaterals was observed by embryonic day (E) 19. Quantification of corticostriatal collaterals revealed a significant increase in the number and complexity of collateral branches at postnatal day 6 as compared to E19. Concomitant with the increase in collateral branching, a heterogeneous pattern of collateralization consisting of parallel rows of corticostriatal collaterals was observed in the medial striatum. In addition to the rows, clusters of corticostriatal axons occurred more laterally. These clusters colocalized with patches of dense tyrosine hydroxylase-positive fibers, a marker for the striatal patch compartment in the neonatal mouse. Together, these data indicate that corticostriatal patterning occurs during the period of early axon collateralization resulting in a segregation of corticostriatal axon collaterals from the prelimbic cortex to the striatal patch compartment.     

Thermomechanical behaviour of composites

This paper derives the governing equations for the thermomechanical behaviour of composites. When the basic equations for the thermoelastic behaviour of solids were first derived in the nineteenth century several approximations were made. The effect of these assumptions are discussed and illustrated by the results of a simple laboratory test. The implications of this work on the analysis of impact damaged laminates are then discussed.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.     

Simplified method for the measurement of segmental colonic transit time

Segmental colonic transit has been measured in 101 patients. Two MBq of 111Indium absorbed on resin pellets and encapsulated in an enteric coated capsule was given at 7 00 am. Hourly images during the first day, and three images during each subsequent day were acquired for up to three days. Using all scan and patient data the scans were categorised in one of the five patterns of colonic transit: normal, rapid, right delay, left delay, or generalised delay. The geometric centres and per cent activity at each time point was compared between the five groups of colonic transit patients to find the best time for imaging and so to distinguish the five groups. During the first day, early images did not help in diagnosis of patterns of transit, however, in the later images (six hours onwards after the ingestion of the activity) the rapid transit groups could be identified. Images at 27 and 51 hours were both required to distinguish all five groups of patients from each other. Only in the 'normal' transit patients was there some excretion of the activity during the course of the second day, otherwise there was no difference in the images taken in the course of a day (second or third day). A simplified protocol requires a minimum of three images to distinguish all five patterns of colonic transit. The activity should be ingested in the morning (7 00 am) and the first image taken at the end of the working day (8-10 hours after ingestion), the second image on the morning of the second day, and the third image during the course of the third day. This simple protocol would provide all the clinically relevant information necessary for correct classification of the colonic transit.     

Analysis of composite laminates with transverse cracks

The analysis of the behaviour of composite laminates with general balanced lay-up sequences and containing distributed transverse cracks is discussed and demonstrated in this paper. It is shown that a constitutive model of damage for composites, which has been successfully used to analyse the effects of uniformly distributed transverse cracks in cross-ply laminates, can be readily extended to the analysis of uniformly distributed transverse cracks in more general symmetric laminates. The further extension of the theory to non-uniformly distributed damage can be achieved by finite element analysis. It is shown that the finite element implementation of the theory is particularly simple since the contribution of the damage to the overall behaviour can be incorporated into the force vectors.