Antitubercular activity of lomefloxacin in an experiment

The effect of lomefloxacin was studied on mice with experimental infection due to Mycobacterium tuberculosis. The antibiotic was administered in doses of 100 and 200 mg/kg. It was shown that the use of lomefloxacin for a month provided a lower death rate of the animals with progressing acute generalized tuberculosis, a lower level of the lesions in the internal organs and a lower number of the Mycobacterium isolates from them. The efficacy of the treatment depended on the drug dose. When lomefloxacin was used in a dose of 200 mg/kg, the survival rate was much higher and the number of the epithelial unicellular granulomas in the tissue of the lung and spleen was markedly decreased while with the lower dose the indices did not differ from those in the control.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

In situ bypass and diabetes

From 1986 through to 1990 a total of 483 in situ bypass procedures were performed in 444 patients. Preoperative risk-factors were equally distributed among diabetic (DM) and non-diabetic (NDM) patients, except for smoking habits (DM:48%, NDM:64%, p = 0.002) and cardiac disease (DM:45%, NDM:29%, p = 0.005). Critical limb-ischaemia was more often present in diabetic than non-diabetic patients (DM:57%, NDM:36%, p = 0.0002). Diabetic patients had a significantly lower distal anastomosis than non-diabetic patients (p = 0.00001). There were no differences among diabetic and non-diabetic patients regarding three years primary and secondary patency (58% and 64% respectively), and regarding major amputations. However, the rate of minor amputations was higher in insulin-dependent compared with non-insulin-dependent diabetics, who in turn had a higher rate than non-diabetics (p < 0.00001). A markedly decreased survival rate was found in diabetics (p < 0.00005). We found the in situ bypass technique very useful in the treatment of critical ischaemia of the lower limb in diabetic patients. The overall results in diabetic patients, whether insulin-dependent or not, were equal to those in non-diabetic patients.     

Detection of anti-HIV-1 IgG antibodies in whole saliva by GACELISA and Western blot assays

The present study, based on 158 HIV seropositives and 167 HIV seronegatives, demonstrates that saliva collected with the Omni-SAL device and tested with GACELISA (an IgG antibody capture ELISA) is an effective non-invasive alternative to serum for anti-HIV IgG antibody screening. The study also shows that a conventional serum Western blot kit can be used, with slight modifications, for confirmatory testing of saliva specimens. Collecting saliva with the Omni-SAL device had a very good acceptance rate among Tanzanian subjects, and although this diagnostic method is not yet known by the general public, 65% of the study participants preferred to give saliva instead of blood for HIV testing.     

GaAs/AlGaAs grating surface-emitting diode lasers on Si substrates

A monolithic grating surface-emitting, GaAs/AlGaAs, separate-confinement-heterostructure, single-quantum-well diode laser has been fabricated on a Si substrate using a single-step metalorganic chemical vapour deposition process. An output power of 30 mW has been obtained under pulsed operation with a peak emission wavelength of 885 nm.<>     

Micromechanical modelling of ductile crack growth in the binder phase of WC–Co

This study focuses on numerical simulation of ductile failure in the Co binder phase of WC–Co hardmetal. The growth of edge cracks under mode I loading is considered. A computational micromechanics approach is taken where the Co binder ligaments are explicitly represented in finite element models. An embedding technique is employed. Crystal plasticity theory is used to represent plastic deformation in the Co ligaments. Crack propagation in the binder is simulated using an element removal technique based on a modified Rice and Tracey model for ductile void growth, and fracture resistance curves are generated. Parameter studies are performed for variations in microstructrual parameters such as numbers of Co ligaments ahead of the crack tip and local Co volume fraction. The importance of thermal residual stresses and finite element mesh density are also investigated.