Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Arterial oxygen desaturation during non-sedated diagnostic upper gastrointestinal endoscopy

We studied oxygen saturation (SaO2) using a pulse oximeter in 120 patients undergoing non-sedated diagnostic upper gastrointestinal endoscopy. The baseline SaO2 was 98.3 +/- 1.0%. During the procedure, absence of oxygen desaturation (SaO2 > or = 95%) was found in 56%, mild oxygen desaturation (95% > SaO2 > or = 90%) in 35%, and severe oxygen desaturation (SaO2 < 90%) in 9%. Age (p = 0.56), gender (p = 0.47), smoking (p = 0.35), hemoglobin level (p = 0.52), body mass index (p = 0.27), or total endoscopy time (p = 0.72) was not related to the degree of oxygen desaturation. These results suggest that oxygen desaturation is frequently observed during non-sedated diagnostic upper gastrointestinal endoscopy although severe oxygen desaturation, which may induce rare but serious cardiopulmonary events, is not common. Furthermore, we cannot predict in which patients desaturation will occur. We therefore recommend continuous monitoring of arterial oxygenation in all patients during the procedure.     

Growth of Al2O3 whiskers by vapour-phase reactions

Needle-like or wool-like Al₂O₃ whiskers can be grown on a substrate by the hydrolysis of aluminium fluoride vapour. Effects of the growth conditions on the morphology of the crystals and growth processes of the whisker were investigated, and the optimum growth condition of whiskers was examined. Adequate vapour pressure conditions of the reactant gases for the growth of the wool-like whisker were found to be . Aluminium oxyfluoride was assumed to be the most probable intermediate species for the growth of Al₂O₃ whiskers. A variety of crystal morphologies are also shown and described with respect to the experimental conditions.     

Activity measurement of gallium in the B2 phase of the CoGa–Sb system by the EMF method with zirconia-based solid electrolyte

Gallium activity in the B2 phase regions of both binary Co–Ga and ternary Co–Ga–Sb systems was measured by EMF method with stabilized zirconia solid electrolyte The temperature range was 1073–1273 K and Sb concentrations were 1, 2 and 3 mol fractions. Ga activity at 1173 and 1273 K increases sharply in Ga rich region and the addition of Sb to the CoGa phase increases Ga activity. Activity change corresponds to the lattice parameter change with Sb addition to the CoGa phase.     

Quantitative structural analysis of twin boundary in alpha-Zn7Sb2O12 using HAADF STEM method

The structure and composition of the 1/4{110} twin boundary in alpha-Zn7Sb2O12 have been determined by using quantitative high-angle annular dark field scanning transmission electron microscopy (HAADF STEM) analysis. The noise in the experimental HAADF STEM images is reduced by using the maximum entropy method and average processing, and the parameters used in dynamical simulations are experimentally determined. From the analysis, it has been found that octahedral sites in the twin boundary slightly shift parallel to the [110] direction, and a reduction of the Sb concentration at the octahedral sites on the plane adjacent to the twin boundary was detected. The reduction was measured from three regions in the same twin boundary, and the Sb concentrations were 4 +/- 3, 8 +/- 3 and 19 +/-2 at% from 33 at%.     

Antireflection coating formed by plasma-enhanced chemical-vapor deposition for terahertz-frequency germanium optics

A method of manufacturing optical coatings for germanium optics used at terahertz frequencies has been developed. The various optical coatings used at terahertz frequencies are difficult to manufacture conventionally because these coatings must be as thick as several tens of micrometers, which is far thicker than those used in the optical region. One way to overcome this problem is to form a silicon oxide layer through plasma-enhanced chemical-vapor deposition, with silane (SiH4) as a source gas. Using this method, I formed 21-microm-thick silicon oxide films as antireflection (AR) layers for germanium optics and obtained low reflection at 1.7 THz (wavelength, lambda = 175 microm). This method is easily applied to large-aperture optics and micro-optics as well as to optics with a complex surface form. The AR coatings can also be formed for photoconductive detectors made from germanium doped with gallium at a low temperature (160 degrees C); this low temperature ensures that the doped impurities in the germanium do not diffuse. Fabrication of optical coatings upon substrates that have refractive indices of 3.84-11.7 may also be possible by control of the refractive indices of the deposited layers.     

Ion-beam processing of single crystal diamond using SOG mask

Various ion-beam etching characteristics of diamond and selectivity between diamond and spin-on-glass (SOG) were examined. The maximum selectivity of diamond and SOG was 12.7 in oxygen reactive ion-beam etching process at 100 V acceleration voltage. Using this etching condition and dot-shaped SOG mask, conical diamond field electron emitter arrays with 30 nm curvature radius, 2.58 μm base radius and 5.86 μm height were fabricated.