Channel estimation based on learning automata for OFDM systems

The abundant benefits of Orthogonal Frequency‐Division Multiplexing and its high flexibility have resulted in its widespread applications in many telecommunication standards. One important parameter for improving wireless system's efficiency is the accurate estimation of channel state information. In the literatures, many techniques have been studied in order to estimate the channel state information. Nowadays, the techniques based on intelligent algorithms such as genetic algorithm and particle swarm optimization (PSO) have attracted attention of researchers. With a very low pilot overhead, these techniques are able to estimate the channel frequency response properly only using the received signals. Unfortunately, each of these techniques suffers a common weakness: they have a slow convergence rate. In this paper, a new intelligent and different method has been presented for channel estimation using learning automata, entitled LA estimator, where the learning automata are search agents, and each pair is responsible for searching 1 complex coefficient of the channel frequency response. This method can achieve an accurate channel estimation with a moderate computational complexity in comparison with GA and PSO estimators. Furthermore, with higher convergence rate, our proposed method is capable of providing the same performance as GA and PSO. For a 2‐path fast fading channel, simulation results demonstrate the robustness of our proposed scheme according to the bit error rate and the mean square error.     

Accurate analysis of spectral regrowth of nonlinear power amplifier driven by cyclostationary modulated signals

In this paper we present an exact analytical expression to calculate the spectral regrowth at the output of a nonlinear power amplifier (PA) using the higher order cumulants and Poisson summation formula. This PA is driven by the filtered digitally modulated signals. To improve the accuracy of the calculations, the cyclosationarity of the input signal is considered. Moreover, closed-form expressions for the 1-dB compression and saturation points are extracted as a function of the PA model parameters, higher order statistics of the input signal, and the transfer function of the pulse shaping filter. In addition, an analytical expression for the adjacent channel power (ACP) and a closed-form expression of the ACP ratio are derived. This is followed by investigation of the effect of the PA nonlinearity on the performance of receiver. Simulation studies are carried out to verify the accuracy of the derived expressions. Excellent agreement between the analytical and simulation results is achieved.     

Sliding-induced adhesion of stiff polymer microfibre arrays. I. Macroscale behaviour.

Gecko-inspired microfibre arrays with 42 million polypropylene fibres cm(-2) (each fibre with elastic modulus 1 GPa, length 20 microm and diameter 0.6 microm) were fabricated and tested under pure shear loading conditions, after removing a preload of less than 0.1 N cm(-2). After sliding to engage fibres, 2 cm2 patches developed up to 4N of shear force with an estimated contact region of 0.44 cm2. The control unfibrillated surface had no measurable shear force. For comparison, a natural setal patch tested under the same conditions on smooth glass showed approximately seven times greater shear per unit estimated contact region. Similar to gecko fibre arrays, the synthetic patch maintains contact and increases shear force with sliding. The high shear force observed (approx. 210 nN per fibre) suggests that fibres are in side contact, providing a larger true contact area than would be obtained by tip contact. Shear force increased over the course of repeated tests for synthetic patches, suggesting deformation of fibres into more favourable conformations.     

Development of electrically conductive hybrid nanofibers based on CNT‐polyurethane nanocomposite for cardiac tissue engineering

Conductive nanofibers have been considered as one of the most interesting and promising candidate scaffolds for cardiac patch applications with capability to improve cell–cell communication. Here, we successfully fabricated electroconductive nanofibrous patches by simultaneous electrospray of multiwalled carbon nanotubes (MWCNTs) on polyurethane nanofibers. A series of CNT/PU nanocomposites with different weight ratios (2:10, 3:10, and 6:10wt%) were obtained. Scanning electron microscopy, conductivity analysis, water contact angle measurements, and tensile tests were used to characterize the scaffolds. FESEM showed that CNTs were adhered on PU nanofibers and created an interconnected web‐like structures. The SEM images also revealed that the diameters of nanofibers were decreased by increasing CNTs. The electrical conductivity, tensile strength, Young's modulus, and hydrophilicity of CNT/PU nanocomposites also enhanced after adding CNTs. The scaffolds revealed suitable cytocompatibility for H9c2 cells and human umbilical vein endothelial cells (HUVECs). This study indicated that simultaneous electrospinning and electrospray can be used to fabricate conductive CNT/PUnanofibers, resulting in better cytocompatibility and improved interactions between the scaffold and cardiomyoblasts.     

An accurate analysis of the nonlinear power amplifier effects on SC-FDMA signals

Wireless Networks - Single carrier-frequency division multiple access (SC-FDMA) is a multiple access technique in broadband wireless networks which has been adapted by 3GPP for uplink transmission...     

Effect of the Wet Outlet Geometry on the Shockwave Position in Supersonic Separators

Supersonic separators (3Ss) are applied in gas separation processes. Two-dimensional simulation is employed to investigate the effect of operational and thermophysical parameters on the shockwave position. In addition, the impact of the cyclonic part and wet outlet geometry is evaluated by proposing four cases. Increasing the length of the cyclonic part exerts positive and negative influences on the performance of the 3S and the pressure recovery coefficient, respectively. The optimum length is determined between 10 and 15 cm. To demonstrate negative effects of wasted air from the wet outlet, its flow has been increased from 3.6 to 8.1 % of the inlet flow. Improved performance of the 3S is obtained by reducing the flow disturbances around the wet outlet and moving the shockwave towards the outlet.