Hopping and optical absorption of electrons in nano-porous crystal 12CaO·7Al2O3

Recently it has been discovered that a nano-porous main group oxide 12CaO·7Al₂O₃ (C12A7) can be converted from a wide-gap insulator to a good transparent conductor. Using ab initio modelling we explain good conductivity of this material by very small barriers for hopping of localised electrons between neighbouring positive cages. We show that optical absorption of C12A7 in infrared region and at energies higher than 2.7 eV is due to inter-cage and intra-cage electron transitions, respectively. The proposed mechanisms can be useful in further search for conducting transparent media.     

Electron transport in InGaO3(ZnO)m (m=integer) studied using single-crystalline thin films and transparent MISFETs

We have investigated the characteristics of transparent metal-insulator-semiconductor field-effect transistors (MISFETs) fabricated using InGaO₃(ZnO)_m (m=integer) single-crystalline thin films as n-channel layers and amorphous alumina as gate insulator films. The MISFETs exhibit good characteristics such as insensitivity to visible light illumination, off-current as low as ∼1 nA with a positive threshold voltage of ∼3 V and on/off current ratio of 10⁵. The field-effect mobility increased from ∼1 to ∼10 cm² (V s)⁻¹ as the m-value increased. Room temperature Hall mobility also increased. However, unexpectedly these values were lower than the field-effect mobility. It is explained by existence of shallow localized state in the homologous compounds.     

An expert system for XPLE cable deterioration diagnosis and life forecasting

The recent increase in the demand for power in urban areas has caused changes in the way power is supplied. Underground distribution systems have been introduced for convenience in urban areas and to prevent injuries in case of a crisis. As a result, many new types of power cables are being used. One type, XPLE cables (also called CV cables) have been rapidly taking the place of conventional cables such as OF or SL cables since the 1960s because of their relatively easy installation and maintainability. However, distribution cables used under severe environmental conditions deteriorate rapidly (due mainly to water treeing), and some cables experience insulation breakdown. Therefore, many diagnostic methods have been developed, though they have not been very effective. By combining methods, a high reliability can be achieved in comparison to the use of a single method. However, processing the data is difficult for on-site personnel, so many experts are required. But there is a lack of qualified experts, hence we have turned to the development of expert systems.     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Dissolution of Ti wires in sulphuric acid and hydrochloric acid solutions

Ti wire electrodes were immersed in acidic solutions containing H₂SO₄ and HCl of various concentrations at 353 K to evaluate corrosion rate by measurement of electric resistance change (resistometry). Addition of hydrochloric acid to sulphuric acid solution promoted depassivation of Ti. After depassivation, the immersion potential dropped to the hydrogen evolution potential and a hydride layer was formed on the surface. The hydride layer dissolved continuously in the acidic solution. SEM observation showed that Ti wires dissolved almost uniformly in the early stage and that the dissolution then trace became irregular due to nonuniform growth of the hydride layer. Dissolution rate of a Ti wire was estimated almost accurately by resistometry.     

Design of nonlinear controllers for active vehicle suspension with state constraints

Design of active vehicle suspension has tradeoffs between three main performance metrics (passenger comfort, suspension deflection and road holding ability). It has been known that each performance can be achieved by H _∞ controller and they can be gathered by LPV (Linear Parameter Varying) method. However, because the suspension deflection limit was not explicitly considered, this limit may be exceeded. In this paper, the authors propose a “reference shaping“ based method in order to improve the control performance. In this approach, a “virtual reference” signal is imposed to the system such that the suspension deflection is kept small. The effectiveness of the approach is examined by numerical simulations. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Suppression of photo-induced dilation in cyanide treated hydrogenated amorphous silicon films

Effects of cyanide (CN) treatment with hydrogenated amorphous silicon (a-Si:H) films have been investigated. The decrease of ΔV/V was observed in cyanide treated a-Si:H films and the successive thermal annealing at 200°C after CN treatment induced the further reduction of the ΔV/V. XPS spectra show the indirect evidence that the cyanide species is present within 10 nm from the hydrogenated amorphous silicon surface. The results of CN treatment with a-Si:H solar cells are demonstrated.     

Software‐processed edge‐ and level‐adaptive overdrive (SELAO) method for high‐quality motion pictures

Abstract— In this paper, a software‐processed edge‐ and level‐adaptive overdrive (SELAO) method, which is a novel overdrive technique that utilizes not only a temporal change of gray levels but also a spatial edge intensity of motion pictures, is proposed. The SELAO method is a software video‐processing technology to improve motion‐picture quality rendered on LCDs more than is possible with a conventional SLAO method without edge‐adaptive overdrive, and it works in real time on commonly used personal computers (PCs).     

Wide gamut LCD using locally dimmable four‐primary‐color LED backlight

This paper proposes a wide gamut LCD using locally dimmable four‐primary‐color (4PC) LED backlight. Although the color gamut of LCDs has been improved in recent years, it is insufficient to reproduce all the colors in the real world. The objective of this paper is to propose a wide gamut LCD that reproduces all the colors in the real world while keeping the cost increases to a minimum. We evaluated the color gamut reproduced by LEDs of multiple primary colors and selected cyan as the optimal color to be added to the three primary colors to reproduce all the colors in the real world. Therefore, we designed an LED backlight consisting of an additional only‐cyan LED with three‐primary‐color LEDs and developed a prototype LCD with 4PC LED backlight. Furthermore, we developed a local dimming algorithm for the 4PC LED backlight. As a result, we confirmed that the prototype LCD with the 4PC LED backlight is able to cover almost all the colors in the real world and also able to display natural images with highly saturated colors by local dimming.