The significance of urinary N-acetyl-beta-D-glucosaminidase for predicting early stage diabetic nephropathy

We studied urinary N-acetyl-beta-D-glucosaminidase (NAG) in the early stage of diabetic nephropathy in 27 non-insulin-dependent diabetes mellitus (NIDDM) patients with a microalbumin level below 20 mg on 24-hour urine sample. Microalbumin and NAG excretion were measured in 24-hour urine samples collected on three separate occasions within seven days of admission. Creatinine clearance was determined simultaneously. There was a significant negative correlation between the creatinine clearance and 24-hour urinary NAG (r = -0.38, p < 0.05). Elevation of urinary NAG may indicate decreased renal function during early stage NIDDM nephropathy.     

BONDING OF CERAMICS TO METALS WITH ACTIVATED COATING LAYERS MADE BY PLASMA SPRAYING

Bonding of ceramics to metals was carried out by using thermal sprayed coatings as interlayer materials. This bonding method is referred as the thermal spray bonding. In the present study, Si₃N₄ and Al₂O₃ ceramics were bonded to SS41 mild steel using activated Ti-Cu multilayer coatings plasma-sprayed on the steel in a low pressure atmosphere. The bondability was estimated by SEM/EDX analysis and shear tests of the joints. The results were compared to those obtained using Ti-Cu multilayer foils as interlayers. When using Ti-Cu foils as interlayers, brittle Fe-Ti compound layers were formed in the joint area after long time heating at a bonding temperature of 900°C, which deteriorated the joint strength. In contrast with the activated interlayers made by plasma spraying, the Ti-Cu eutectic reaction took place uniformly at the joint immediately after heating to the bonding temperature. This improved the bondabilrty, and the resultant joints exhibited shear strengths of about 180 MPa.     

Comparative clinical study of adjuvant postoperative chemotherapy (5-FU, Tegafur, 5-FU + MMC) in curatively resected cases of gastric cancer. Study Group on 5-FU Oral Adjuvant Chemotherapy in Gastric Cancer

A multi-center collaborative study was conducted in curatively resected gastric cancer patients at Stages II and III to compare oral 5-FU (Group A), oral Tegafur (Group B) and i.v. MMC + oral 5-FU (Group C). From May 1982 to April 1985, 1,012 cases were enrolled at 55 institutions. Some 138 (13.8%) were excluded, and 874 were analyzable. In the analysis of background factors, Group B had more cases with tumor of large diameter and advanced Stage. Adverse effects were relatively mild in all groups, and there was no problem in drug tolerance. Five-year survival rate was 67.6%, 62.4% and 68.6% in Groups A, B and C, respectively, reflecting no significant difference among them. It was 85.0%, 83.0% and 81.1% in Stage II and 52.5%, 51.0% and 59.0% in Stage III of Groups A, B and C, respectively. No significant difference was found, but Stage III of Group C showed a slightly higher survival rate. Supportive clinical study will be required to assess the usefulness of MMC as an introduction therapy. We found no difference in efficacy between 5-FU and Tegafur as maintenance therapy. The life-prolongation effect of fluoropyrimidines in comparison with surgery alone should be studied separately.     

Eight-channel flat spectral response arrayed-waveguide multiplexer with asymmetrical Mach-Zehnder filters

An eight-channel flat spectral response arrayed-waveguide grating (AWG) multiplexer with asymmetrical Mach-Zehnder filters has been fabricated on the planar lightwave circuit (PLC). The monotonic spectral loss characteristics of AWG have been canceled by the opposite spectral response in the asymmetric MZ filter. The 1.5 dB bandwidth of 141 GHz and 3 dB bandwidth of 159 GHz are obtained for the 200 GHz channel spacing. The 1.5 dB bandwidth becomes 1.8 times wider than that of the conventional AWG. Crosstalks to neighboring and all other channels are less than -24 dB and the on-chip insertion losses range from 7.0 to 7.4 dB, respectively.     

Formation of an amorphous phase in thermally sprayed WC-Co

A WC-Co coating was sprayed by the high-velocity oxyfuel process using a feedstock of tungsten carbide clad with cobalt. The structure of the sprayed coating was characterized by x-ray diffraction (XRD), differential scanning calorimetry (DSC), and differential thermal analysis (DTA). It was found that an amorphous phase of Co-W-C ternary alloy observed as a large, broad peak in the XRD pattern can be formed in the as-sprayed WC-Co coating. The DSC, DTA, and XRD analyses revealed that the amorphous phase crystallized at a temperature of around 873 K to metallic cobalt, Co₆W₆C, and tungsten with appreciable precipitation of free carbon. The heat treatment of as-sprayed WC-Co coating at a high temperature of 1173 K suggests that annealing at a temperature higher than about 1104 K will promote the reaction of tungsten and cobalt with carbon to form the complex carbide C₀₆W₆C.     

Microstructural Analysis and Photocatalytic Activity of Plasma-Sprayed Titania-Hydroxyapatite Coatings

Hydroxyapatite (HAp Ca₁₀(PO₄)₆(OH)₂) is known to be a biomaterial and an adsorbent for chromatography. In this study, HAp was agglomerated with anatase TiO₂ to manufacture thermal-spray powders to improve the adsorption activity of TiO₂, and then to improve its photocatalytic activity. The microstructures, compositions and photocatalytic activity of plasma-sprayed TiO₂, TiO₂-10%HAp, TiO₂-30%HAp, and HAp coatings were investigated. Due to the low thermal conductivity of HAp compound, not all HAp particles fully melted even under the arc current of 800 A. The addition of HAp inhibited the phase transformation of anatase TiO₂ to rutile. Under the arc current of 600 A, the anatase content in the TiO₂, TiO₂-10%HAp and TiO₂-30%HAp coatings was 11, 20 and 42%, respectively. With the increasing of the spraying distance from 70 to 110 mm, the anatase content in the TiO₂-30%HAp coatings decreased from 34 to 17% under arc current of 700 A. Furthermore, a slight decomposition of HAp to α-Ca₃(PO₄)₂ was found in the TiO₂-30%HAp coatings, it did not decompose to CaO and P₂O₅ according to the XRD and EDAX analysis. The addition of the secondary gas of helium had no significant influence on the melting state of the TiO₂-HAp feedstock powders. Moreover, the HAp in the TiO₂-10%HAp and TiO₂-30%HAp coatings had adsorption characteristic to acetaldehyde. The photocatalytic activity of TiO₂-10%HAp coating was highest among TiO₂, TiO₂-10%HAp, and TiO₂-30%HAp coatings sprayed under the arc current of 600 A for the optimum adsorption property and anatase content. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Penetration treatment of plasma-sprayed ZrO2 coating by liquid Mn alloys

The penetration phenomena of liquid manganese (Mn) alloy into porous ZrO₂ (8 vvt % Y₂O₃) coating plasma sprayed on SS400 steel substrate was studied by heating in a vacuum atmosphere. The improvement in mechanical properties of the coating by heat treatment with liquid Mn alloys was examined. Liquid Mn alloys, such as Mn-Cu, Mn-Sn, and Mn-In, rapidly penetrated the coating and formed a chemical bond between the coating and the substrate. The densification of the ZrO₂ coating occurred when ZrO₂ particles were sintered with liquid Mn alloys that penetrated the porous coating. The dense coating was free of porosity, and its hardness increased after heat treatment with Mn alloys, compared with assprayed ZrO₂ coating. Moreover, the fracture toughness of the coating reached the same levels as those of sintered yttria-stabilized PSZ.     

低气压等离子喷涂TiO2涂层结构的研究

本研究分析了在低气压等离子喷涂条件下,TiO_2涂层的结构受等离子弧喷涂过程中氧分解量所影响。氧分解量很大程度上依赖于离子气中氢流量的大小,此外喷涂室压力也有一定影响。而等离子弧功率和喷涂距离对TiO_2涂层的氧分解量没有多大影响。在离子气中氢流量不变的条件下,涂层中Ti_3O_5量随喷涂室压力(从100×133.322Pa至400×133.322Pa)增加而增加。     

Output intersampling approach to direct closed-loop identification

A new direct closed-loop identification method, which uses the output intersampling technique, is proposed in this note. By using the intersampled plant input-output data, the proposed method removes the traditional restrictive identifiability condition, and does not require an external persistently exciting (PE) test signal     

Relationship between particle erosion and lamellar microstructure for plasma-sprayed alumina coatings

The lamellar structure determines mechanical properties of a thermal spray coating. A model for the erosion of thermally sprayed ceramic coatings resulting from the debonding of flattened ceramic particles is proposed based on the examination of the erosion mechanism. The relationship between erosion rate and microstructural parameters is established both experimentally and theoretically to reveal main lamellar structural parameters controlling erosion of thermally sprayed ceramic coating. The microstructural parameters include the mean bonding ratio between lamellae and thickness of the lamellae. The erosion rate of plasma-sprayed Al₂O₃ coatings was measured at impact angle of 90° under the fixed erosion test conditions. The correlation of theoretical model with the observed structural parameters and erosion data of alumina coatings was examined. It is revealed that the theoretical relationship agreed well with the observed relation. The results clearly revealed that the erosion of plasma-sprayed ceramic coating was inversely proportional to the mean lamellar bonding ratio. The influences of spray parameters on erosion effected mainly through their influences on the lamellar bonding. The erosion resistance of a thermally sprayed ceramic coating was controlled by coating fracture toughness.