EC Analysis of Multi-Antenna System over 5G and Beyond Networks and its Application to IRS-Assisted Wireless Systems

Wireless Personal Communications - Recently, the theory of effective rate has attracted much attention, since it can take the delay aspect into account when performing channel capacity analysis. In...     

Domain Adaptation for POS Tagging with Contrastive Monotonic Chunk-wise Attention

Neural Processing Letters - Part of Speech (POS) tagging is a sequential labelling task and one of the core applications of Natural Language Processing. It has been a challenging problem for the...     

Effect of 100 KeV Ar+ ion beam irradiation on ZnO thin films – Influence of morphology vis-a-vis electrode/electrolyte interface and its impact on photoelectrochemical water splitting

The present study attempts quantitative determination of changes in the morphological surface features viz. fractal dimension, lower and upper cut off length scale through Power Spectral Density analysis prior to and after irradiation of 100 KeV Ar⁺ ion beam at incidence angles of 0°, 40° and 60° on ZnO thin films. All the unirradiated and irradiated samples are subjected to photoelectrochemical characterization and a correlation between photoelectrochemical performance and morphological parameters is established. Sample irradiated at 40° angle at the fluence of 5 × 10¹⁶ ions/cm² is found to possess maximum fractal dimension of 2.72, lower and upper cut off length scale of 3.16 nm and 63.00 nm respectively. This sample exhibits maximum photocurrent density of 3.19 mA/cm² and applied bias photon-to-current efficiency of 1.12% at 1.23 V/RHE. Hydrogen gas collected for duration of 1 h for the same sample was ~4.83 mLcm^?2.     

Impact of Mole Fractions due to Work Function Variability (WFV) of Metal Gate on Electrical Parameters in Strained SOI-FinFET

In the recent sub-20 nm technology node, the process variability issues have become a major problem for scaling of MOS devices. We present a design for a strained Si/SiGe FinFET on an insulator using a 3D TCAD simulator. The impact of metal gate work function variability (WFV) on electrical parameters is studied. Such impact of WFV for different mole fractions (x) of the SiGe layer in a strained SOI-FinFET with varying grain size is presented. The results show that as the mole fraction is increased, the variability in threshold voltage (σVT) and off current (σIoff) is decreased; while, the variability of on-current (σIon) is increased. A notable observation is the distribution of electrical parameters approaches a normal distribution for smaller grain sizes.     

A prospective study of closure techniques of abdominal incisions in infants and children

In a prospective study of layered versus mass closure of abdominal incisions in infants and children, 34 cases underwent wound closure by layered and mass closure technique on an alternate basis. All the patients were assessed for their nutritional status and haemoglobin level pre-operatively, and wound complications were compared with respect to closure technique, nutritional status and normal haemoglobin level. Presence of protein energy malnutrition and anaemia did not increase the risk of wound complications with either of the technique.     

Cut off frequency and transit time analysis of lightly doped drain (LDD) MOSFETs

Analytical model for the transconductance, cut off frequency, transit time and fringing capacitance of LDD MOSFETs is presented with a simple approach. The analysis is carried out considering the LDD device as a conventional MOSFET with a series resistance [Z.-H. Liu et al., Threshold voltage model for submicrometer MOSFETs. IEEE Trans Electron Devices 1993; ED-40: 86–94] and a simple closed form expressions for cut off frequency and transit time is obtained. The total gate capacitance, i.e. the geometric and fringing capacitance, is calculated for both LDD and non-LDD devices and lower fringing capacitance is reported in LDD devices. Lower cut-off frequencies and higher transit time are reported in LDD devices for the same channel length.     

Microstructural Investigation on Failure of Internal Drive Shaft

17-4 PH stainless steel is used as internal drive shaft material in liquid engine pumps. One of the drive shafts failed during operation. The shaft pieces were in contact for short duration after failure, which has resulted in abrasion of fractured surfaces. Samples from the location of failure were taken, and investigation of the failure was carried out using optical and scanning electron microscopy. The microstructural analysis of the material and fractographic analysis of the fractured surface show that the failure was caused by excessive torsion.     

Corrosion characteristics of aluminium alloy graphite particulate composite in various environments

The present study was aimed at understanding the response of 2014 Al alloy dispersed with graphite particles in various corrosive environments. Marine (sodium chloride) as well as acidic media were selected for the purpose with a view to widen the range of utility of the composite for applications where such environments may be encountered. Studies were also extended to characterize the corrosion resistance of the composite in fresh as well as used lubricating oils to explore the possibilities of using it in bearing, bushing and such other applications. The corrosion behaviour of the base alloy processed under identical conditions was also examined in the above media to see the influence of graphite addition in the alloy. In order to assess the role of the matrix microstructure, the composite as well as the base alloy was subjected to corrosion in heat-treated as well as-cast conditions. It was observed that the specimens suffered from the maximum rate of corrosion in acid, while sodium chloride produced the minimum corrosion rate. Oil in both used and fresh conditions revealed a negligibly small extent of corrosion. The composite was found to show a higher rate of corrosion than the base alloy under identical test conditions. This was attributed to the dispersoid/matrix interfacial corrosion in the case of the graphitic aluminium alloy. Heat treatment of the composite and the base alloy was found to lower the rate of corrosion in the environments tested. Microstructural modifications of the matrix and possible relief of residual stresses were thought to be responsible for the lower rate of corrosion in the heat-treated condition.