Inferring kinetic dissolution of NaCl in aqueous glycol solution using a low-cost apparatus and population balance model

An experimental methodology for inferring brine dissolution rate in monoethylene glycol (MEG) solutions at different temperatures using a webcam combined with a mathematical model is presented. The measurement system is designed to track the RGB (red, green, and blue) colour variations during the dissolution process. A dynamic model augmented with the population balance equation is applied to describe the dissolution process. Moreover, the dissolution rate is consistently related to the temperature and MEG concentration through the driving force based on the Gibbs energy and chemical affinity. The applied low-cost measurement apparatus proved to be a useful resource for tracking the dissolution dynamics in a wide range of undersaturation.     

Influence of the second phase on the room-temperature tensile and creep deformation mechanisms of α-β titanium alloys: Part I. Tensile deformation

The effects of α and β phase interactions on the room-temperature tensile and creep deformation behavior of α + β titanium alloys with Widmanst?tten microstructures were studied using Ti-6.0 wt pct Mn and Ti-8.1 wt pct V as the model two-phase alloy systems. This article, Part I, deals with tensile deformation. It was found that when the α phase is present as thin (<10-μm) plates in the α + β alloys, significant twinning occurs. No significant twinning was observed in single-phase alloys with the same chemistry and similar grain size. Additionally, the β phase of Ti-8.1 V deforms by stress-induced hexagonal martensite (α′), while only twinning occurs in the single-phase β alloy with the same chemistry. Twinning in the α phase in association with stress-induced martensite (SIM) in the β phase was observed for the first time in a two-phase titanium alloy. This behavior is explained in terms of a number of factors including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability.     

Measurements of small-scale fading and path loss for long range RF tags

RF modulated backscatter (RFMB), also known as modulated radar cross section or sigma modulation, is a RF transmission technique useful for short-range, low-data-rate applications, such as nonstop toll collection, electronic shelf tags, freight container identification and chassis identification in automobile manufacturing, that are constrained to have extremely low power requirements. The small-scale fading observed on the backscattered signal has deeper fades than the signal from a traditional one-way link of the same range in the same environment because the fading on the backscattered signal is the product of the fading on the off-board-generated carrier times the fading on the reflected signal. This paper considers the continuous wave (CW) type of RFMB, in which the interrogator transmitter and receiver antennas are different. This two-way link also doubles the path loss exponent of the one-way link. This paper presents the cumulative distribution functions for the measured small-scale fading and the measured path loss for short ranges in an indoor environment at 2.4 GHz over this type of link.     

The influence of oxygen partial pressure on growth of the (Hg,Re)-1223 intergrain junction

Hg/sub 0.82/Re/sub 0.18/Ba/sub 2/Ca/sub 2/Cu/sub 3/O/sub 8+/spl delta// polycrystalline samples were successfully obtained by using different oxygen partial pressure in the annealing treatment of the precursor ceramic. The doping state was confirmed by X-ray powder diffraction pattern analysis and by observing distinct thermopower values at room temperature. Also, the intergrain regions have shown an improvement in the critical current density when using the precursor preparation with 10% O/sub 2/ and 90% Ar (optimal doped). The optimal doped sample has presented the highest /spl alpha/ exponent of the J/sub c//spl prop/[1-(T/T/sub c/)/sup 2/]/sup /spl alpha// dependence. For the case of (Hg,Re)-1223 polycrystalline superconductor applications, the /spl alpha/ exponent can be used as a junction quality parameter.     

Towards implementation of a nickel silicide process for CMOS technologies

In this paper, we review some of the advantages and disadvantages of nickel silicide as a material for the electrical contacts to the source, drain and gate of current and future CMOS devices. We first present some of the limitations imposed on the current cobalt silicide process because of the constant scaling, of the introduction of new substrate geometries (i.e. thin silicon on insulator) and of the modifications to the substrate material (i.e. SiGe). We then discuss the advantages of NiSi and for each of the CoSi₂ limitations, we point out why Ni is believed to be superior from the point of view of material properties, miscibility of phases and formation mechanisms. Discussion follows on the expected limitations of NiSi and some of the possible solutions to palliate these limitations.     

Probabilistic Weibull behavior and mechanical properties of MEMS brittle materials

The objective of this work is to present a brief overview of a probabilistic design methodology for brittle structures, review the literature for evidence of probabilistic behavior in the mechanical properties of MEMS (especially strength), and to investigate whether evidence exists that a probabilistic Weibull effect exists at the structural microscale. Since many MEMS devices are fabricated from brittle materials, that raises the question whether these miniature structures behave similar to bulk ceramics. For bulk ceramics, the term Weibull effect is used to indicate that significant scatter in fracture strength exists, hence requiring probabilistic rather than deterministic treatment. In addition, the material's strength behavior can be described in terms of the Weakest Link Theory (WLT) leading to strength dependence on the component's size (average strength decreases as size increases), and geometry/loading configuration (stress distribution). Test methods used to assess the mechanical properties of MEMS, especially strength, are reviewed. Four materials commonly used to fabricate MEMS devices are reviewed in this report. These materials are polysilicon, single crystal silicon (SCS), silicon nitride, and silicon carbide.     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results