Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Prolonged tamoxifen exposure selects a breast cancer cell clone that is stable in vitro and in vivo

The effects of long-term tamoxifen exposure on cell growth and cell cycle kinetics were compared between oestrogen receptor (ER)-positive (MCF-7) and ER-negative (MDA-MB-231) cell lines. In the MCF-7 cell line, prolonged tamoxifen exposure (0.5 mumol/l for > 100 days) blocked cells in G0-G1 of the cell cycle, and slowed the doubling time of cells from 30 to 59 h. These effects corresponded to an increase in the cellular accumulation of tamoxifen over time [mean area under concentration curve (AUC) = 77.92 mumoles/10(6)/cells/day]. In contrast, in the MDA-MB-231 cell line, long-term tamoxifen exposure had no obvious effect on the doubling time, and reduced cellular tamoxifen accumulation (mean AUC = 50.50 mumoles/10(6)/cells/day) compared to the MCF-7 cells. Flow cytometric analysis of MDA-MB-231 cells demonstrated that a new tetraploid clone emerged following 56 days of tamoxifen exposure. Inoculation of the MDA-MB-231 tetraploid clone and MDA-MB-231 wildtype cells into the opposite flanks of athymic nude mice resulted in the rapid growth of tetraploid tumours. The tetraploid tumours maintained their ploidy following tamoxifen treatment for nine consecutive serial transplantations. Histological examination of the fifth transplant generation xenografts revealed that the tetraploid tumour had a 25-30 times greater mass, area of haemorrhage and necrosis, a slightly higher mitotic index and was more anaplastic than the control neoplasm. The control wildtype MDA-MB-231 tumours maintained a stable ploidy following tamoxifen treatment until the eighth and ninth transplantation, when a tetraploid population appeared, suggesting that tamoxifen treatment may select for this clone in vivo. These studies suggest that prolonged tamoxifen exposure may select for new, stable, fast growing cell clones in vitro as well as in vivo.     

Thermomechanical behaviour of composites

This paper derives the governing equations for the thermomechanical behaviour of composites. When the basic equations for the thermoelastic behaviour of solids were first derived in the nineteenth century several approximations were made. The effect of these assumptions are discussed and illustrated by the results of a simple laboratory test. The implications of this work on the analysis of impact damaged laminates are then discussed.     

Development of Stretch Solder Interconnections for Wafer Level Packaging

A wafer level packaging technique has been developed with an inherent advantage of good solder joint co-planarity suitable for wafer level testing. A suitable weak metallization scheme has also been established for the detachment process. During the fabrication process, the compliancy of the solder joint is enhanced through stretching to achieve a small shape factor. Thermal cycling reliability of these hourglass-shaped, stretch solder interconnections has been found to be considerably better than that of the conventional spherical-shaped solder bumps.